Vendlet STANDARD User manual
VALUE IN CARING
MANUAL
S TA N DA R D
Vendlet ApS hereby declare that the devices menoned below comply with the Medical Device
Regulaon (EU) 2017/745.
Legal manufacturer: Vendlet ApS, Egelund 33, 6200 Aabenraa, DK
Device: Product no. and name
6300000 VENDLET Standard
UDI-DI:
05714038001094
Basic UDI-DI: 05714038001049EU
Descripon: Electromechanical turning aid for handling and turning paents
in bed.
Classicaon, rule: Class I acc. to rule 1 and 13 of annex VIII in (EU) 2017/745.
The product complies with
the following standards:
EN 60601-2-52:2010 Medical electrical equipment – Part 2-52:
Parcular requirements for basic safety and essenal perfor-
mance of medical beds
60601-1-2:2015 Medical electrical equipment. General require-
ments for basic safety and essenal performance - Collateral
Standard: Electromagnec disturbances - Requirements and test
This declaraon of conformity is valid from the date of signature.
Aabenraa, 02.11.2021
Peter Maindal
Director
Congratulaons on your new VENDLET.
The VENDLET is used for handling bedridden clients,
for example:
• turning the client to lateral, prone or supine posions
• moving the client from one side of the bed to the other
• reposioning the client up in the bed
• mobilizing the client in and out of bed
This manual covers VENDLET Standard.
Max. user weight is 250 kg
The instrucons in this manual must be followed. Vendlet
ApS shall not be liable should VENDLET Standard be used,
modied, or assembled in a way that is not described in this
manual.
This manual is divided into three parts:
Part 1 contains general informaon that is useful to everyone
responsible for the purchasing, examinaon, use, assembly,
and maintenance of VENDLET Standard.
Part 2 is a user manual containing informaon about the oper-
aon and daily maintenance of VENDLET Standard.
Part 3 is a technical manual containing informaon about the
assembly, maintenance, and service of VENDLET Standard.
Independent living 7
Sta7
Environment 7
Turning 12
Moving from one side of the bed to the other 13
Reposioningtheclientupinthebed 14
Applying a sling 15
Proneposion 16
Side rail 17
Tools26
Overviewofbolts 26
Dimensionalrequirements,siderails 26
Maximum loads 27
Aachingaside 27
Height adjustment 29
Mounngthecontrolunit 30
Connecngthecontrolunit 31
Connecngthepowercables 32
Aachingtheturningsheetbeforeuse 19
What should I do if the turning sheet is rolled askew on the bars? 19
Changingtheturningsheetonanoccupiedbed 20
Cleaningofelectricalandmechanicalparts 23
Washinginstrucons,slidesheet 23
Washinginstrucons,turningsheet 23
Electricalparts 35
Mechanicalparts 35
Sheets 35
Funconaltests 35
Rechargingduringstorage 37
LEDfunconality 37
Buzzerfunconality 37
PART 1 - General information
7
VENDLET Standard may be used for moving clients to a lateral,
prone, or supine posion, from one side of the bed to the oth-
er, or, to reposion them further up in bed. VENDLET Standard
may also be used in connecon with mobilizaon in and out of
bed.
VENDLET Standard protects the caregiver from physical strain
and heavy liing in connecon with the handling of immobile
clients. Clients are turned/handled by pressing a hand control
whereby the caregiver may support the client and ensure their
correct and comfortable posioning. This provides room for
increased awareness in the care, which boosts employee job
sasfacon and client well-being.
To the client, the turning process becomes uniform and steady
as the sheet supports the body over its full length.
The target group is adult clients who are being cared for,
dressed, washed etc. in bed. This will oen be clients who are
lied in and out of bed or clients who are mobilized using a
standing aid. Hence, the user will typically be clients with few
physical and/or cognive resources and palliave clients.
VENDLET Standard is also suitable for clients at risk of devel-
oping pressure ulcers. The uniform and steady transfer with
the sheet minimizes fricon and the associated shear that can
damage the ssue and cause pressure ulcers. Furthermore,
VENDLET Standard is oen seen to have a posive eect on
clients suering from spaal awareness.
The VENDLET Standard is intended for adult clients weighing
between 30 and 250 kg, with a height above 146 cm and a
body mass index (BMI) above 17.
There are no contraindicaons for the use of VENDLET Stand-
ard . However, prior to the rst use of VENDLET Standard, it
is important to assess whether VENDLET Standard is suitable
for the client in queson. It may be necessary to take special
precauons, for example if a client is very restless in bed or has
an untypical anatomy.
Independent living
VENDLET Standard is not designed to be operated by the cli-
ents themselves. However, if a risk assessment made by the
responsible healthcare professional evaluate, that the client is
able to take part in the moving and handling procedures, e.g.
by operang the hand control, this can be a part of the rehabil-
itave eort.
The risk assessment should evaluate the clients physical,
cognive and palliave resources. The risk assessment must be
available by the bed and must be updated on a regular basis.
Vendlet ApS cannot be held responsible for the risk assessment
or conclusions based on this.
Sta
Before using VENDLET Standard, it must be ensured that the
caregivers/operators have read “Part 2 – User manual” and
that the manual and quick guide are available by the bed.
Environment
VENDLET Standard can be used in all applicaon environments
(1-5), e.g. hospitals, nursing homes and domesc / private
homes.
VENDLET Standard consist of two bars ed with motors. The
bar on the le side of the client has a blue color marking and
the bar on the right side of the client has a red color marking.
Each motorized bar has a groove which makes it possible to at-
tach the edge strip of the turning sheet to the bars. When the
bars are running, the turning sheet will be dragged between
the two bars, making it possible to move it from side to side.
A slide sheet is inserted under the turning sheet in order to
reduce the fricon of the turning sheet against the maress.
Four corner posts are ed with a build-in actuator in order to
raise and lower the bars with the press of a buon.
VENDLET Standard can be adjusted in height, which makes it
easy to adapt the system to the individual maress and bed.
Furthermore, VENDLET Standard consist of a control unit and
a hand control. The control unit is placed underneath the bed,
normally on the base frame.
When the bars are raised VENDLET Standard works as side
rails.
VENDLET Standard is telescopic in length and can be extended
from 200 to 220 cm.
PART 1 - General information
8
VENDLET Standard is switched on by double-clicking the
on the hand control. VENDLET Standard produce a “beep”
upon acvaon and the green diode over the power symbol
turns on.
When VENDLET Standard hasn’t been used for 90 seconds, the
system produces a “beep-beep” sound, the diode turns o,
and then VENDLET Standard is turned o.
When VENDLET Standard is turned on, the bars can be turned
in both direcons or raised or lowered. The colour coding on
the bars relates to the colours on the hand control buons.
The speed of the bars can be reduced to 75% or 50% of normal
speed.
Press and hold the individual buons long enough to obtain
the desired operaon; the motors will stop when the buon
is released. Likewise, you may stop an acvated funcon by
clicking the .
The emergency release nut must only be used in case of emer-
gency (see page 21) or malfuncon of the actuators.
VENDLET Standard hand control
Power with light /
stop buon
Tighten the sheet
on the red bar
Slacken the sheet
on the red bar
Raise the red bar
Lower the red bar
Speed Adjustment
Tighten the sheet
on the blue bar
Slacken the sheet
on the blue bar
Raise the blue bar
Lower the blue bar
Flash light
Red corner post
with build-in actuator
Head end
Red corner post
with build-in actuator
Foot end
Blue corner post
with build-in actuator
Head end
Blue corner post
with build-in actuator
Foot end
Turning sheet
Blue bar
Red bar
VENDLET Standard
Emergency
release nut Height
adjustment
Reset*
* If the hand control is ashing, reset the system by simultaneously press-
ing the two top buons on the hand control. You will hear 10 rhythmic
beeps. Press and hold the buons unl the beeping stops.
Watch vidoes on how the hand control works
on our webpage www.vendlet.com
or scan the QR-koden.
PART 1 - General information
9
When the bar is up on the side where the turning sheet is be-
ing ghtened, the client will be turned. If, on the other hand,
the bar is down on the side where the turning sheet is being
ghtened, the client will be moved towards the edge of the
bed. These fundamental principles provide you with a num-
ber of ways to move and/or transfer clients. See the “How to
use VENDLET Standard” secon in “Part 2 – User Manual” for
further details.
VENDLET Standard can be operated by only one caregiver.
As it is recommended that the client does not
operate VENDLET Standard themselves, the hand
control must be placed on the outside of the bed
before leaving the client.
The client must not operate VENDLET Standard
on their own unless a qualied risk assessment
has been carried out. Vendlet ApS cannot be held
responsible for the risk assesment or conclusions
based on this.
Always, keep focus on the client when using
VENDLET Standard.
If the client has long and loose hanging hair, the
hair could in some situaons be rolled onto the
bar. Therefore, long loose hair should be collect-
ed before moving and handling the client.
Be aware, that the client does not get too close
to the edge of the bed, as there is a risk of falling
out of the bed.
Do not use VENDLET Standard if the bars can not
be elevated properly.
Lowering the bed to a very low posion may
leave the corner post close to the oor.
Consequently, you should not place your feet
under the corner posts.
The client must not hold on to the edge of the
turning sheet or bar during the transfer. If the
client is restless and needs something to hold on
to, we recommend they get a handle such as a
MANULET Mono Grip.
The power buon also funcons as a stop
buon.
If the hand control buon controlling the ght-
ening of the sheet fails, the operaon can be
stopped by pressing the buon.
Addional hand control:
An addional hand control can be connected if a hand control
is required on both sides of the bed.
Wider sheets:
Wider turning sheets and slide sheets are also available if
VENDLET Standard is to be used on wider beds, see page 18.
Baery backup:
Baery backup is available to operate VENDLET Standard
without a connecon to the supply network. See page 37 for
technical informaon on the baery backup.
PART 1 - General information
10
VENDLET Standard is intended for mounng on a wide range of
hospital and care beds and with a wide range of maresses.
The following bed and maress requirements must be met.
The bed must meet the EN 60601-2-52 standard or the expired
EN 1970 or EN 60601-2-38 standards.
The bed must have a square steel frame (dimensions H 45-78
mm, W min. 20 mm, L min. 1830 mm) without protrusions.
Inner distance between the head- and foot board must be at
least 200 cm. The bed width is not crucial as extra wide turning
sheets and slide sheets are available.
VENDLET Standard can be mounted on most beds with these
dimensions. But situaons where VENDLET Standard cannot be
mounted can occur.
The maximum user weight and safe working load
of the bed must not be exceeded following the
installaon of VENDLET Standard, see page 27.
The maress must meet the requirements of the
bed manufacturers and be suitable for the bed.
The maximum user weight specicaon of the maress must
not be exceeded.
Following the mounng of the VENDLET Stand-
ard, the distance between the maress sides and
side rails must be minimum 2.5 cm and maxi-
mum 4 cm, see page 26.
If the maress is so and easily compressible,
it must be ensured that there is no entrapment
hazard due to extra compression at the edge of
the maress.
When alternang air maresses are used, it should be possible
to inate the maress to a rm state before VENDLET Standard
is operated. So maresses will increase the fricon against
the maress and create an uneven base which will be uncom-
fortable for the client when VENDLET Standard is operated.
If the client changes maress, the VENDLET
installaon must be evaluated. A new maress
might change the condions and necessitate the
reinstallaon of VENDLET Standard to reduce the
risk of entrapment.
Vendlet ApS provides a 2-year factory warranty on VENDLET
Standard. The warranty is void if the product is not used,
handled and maintained in accordance with the guidelines in
this manual. Opening the control unit, the bar, the corner post,
or the hand control will also void the warranty.
The warranty does not include the sheets.
The VENDLET Standard service life is 10 years. The service life
may be signicantly extended if the product is used and
handled with care and maintained in accordance with the
guidelines in this manual.
The VENDLET Standard must be serviced annually by a person
with relevant training, see page 35.
In case of an adverse event or a near-accident involving VEND-
LET Standard, the accident must be reported to the competent
authority in the country in which the accident happened and
to the Danish Health and Medicines Authority.
Likewise, Vendlet ApS must also be informed on phone
+45 9631 0050 or vendlet@vendlet.dk.
PART 1 - General information
11
CE marking: The product complies with the
Medical Device Regulaon (EU) 2017/745
MD This product is a medical device
Legal manufacturer
Date of manufacture
Serial number
Item no. / Catalogue number: 7 digits
Unique Device Idencaon
Consulng the manual is mandatory
Warning triangle indicates when special aenon is
necessary
For indoor use
This product is a class ll equipment (IEC 61140)
The product is a type B equipment according to EN
60601-1
Max. user weight
Electronic scrap. When disposing of the products,
sub-components should be recycled
Washable This product is washable acoording to EN 60101-2-52
U In:100-220
VAC @ 60 Hz or
100-230 VAC @
50 Hz
The mains voltage must be 100-220 Volt AC @ 60 Hz or
100-230 Volt AC @ 50 Hz
350 W Max power consumpon is 350 W
(SMPS: Switch mode power supply).
I In:
max.4,5A The current used is max 4,5 A
Int.:10% -
2/18min on/o
The system should only be used 10% of the me. Aer 2
min of connuous use it requires 18 min rest.
Max 350W/80
sec./
175W/40sec
@25˚C
In connuous use at 25˚C 350 W can be supplied for 80
sec - then the power consumpon will be reduced to 175
W for 40 sec.
0
50°C
This product must be stored between 0 and 50˚C
5
40°C
This product must be used between 5 and 40˚C
20
90% This product must be stored between 20 and 90 %
humidity at 30˚C
Keep dry (when stored)
Rev. Revision no. of the label
Power / stop buon
Speed Adjustment
Flash light on hand control
Tighten the sheet on the red or blue bar
Slacken the sheet on the red or blue bar
Raise the red or blue bar
Lower the red or blue bar
Connect control unit extension to control unit
Connect baery to control unit
The hand control and the control unit complies with the EMC
Direcve 2014/30/EU and the Low Voltage Direcve 2014/35/
EU
The component complies with the EMC regulaon of Australia
and New Zealand.
The component complies with China RoHS.
Type + item Product no/catalogue no
Date Date of producon
W/O Work order
The product / system label is placed on the corner posts at the foot end.
PART 2 - User manual
12
Turning
VENDLET Standard may be used to turn clients. Turning clients
with VENDLET Standard is ideally suited for dressing and
access to care tasks and hygiene, applying a sling, and reposi-
oning.
Follow this procedure to move a client from a supine posion
to lying on his/her right side.
1. Turn VENDLET Standard on by double clicking the
buon.
2. Press the buon to raise the blue bar.
3. If necessary, press once or twice on the buon to
reduce speed.
4. Press the buon to ghten the turning sheet on the
blue bar.
5. Place the le arm of the client on his/her stomach or
chest the moment before he/she starts turning.
6. Immediately aer this, guide the right arm of the client to
the side.
OPERATION
Handling clients with VENDLET Standard enables caregivers to
work on a one-to-one basis: one hand is used to operate the
hand control and the other hand is free to guide the arms and
legs of the client. In order to improve the safety and well-being
of the client, we recommend that you place the hand holding
the hand control on the shoulder of the client or similar.
You should always use the resources of the client. For example,
if the client can move his/her arm to the side, he or she should
do so. You should also consider leng the client operate the
hand control and thereby involve him/her in the process if
this is feasible. However, the client must not operate VENDLET
Standard on their own unless a qualied risk assessment has
been carried out. Vendlet ApS cannot be held responsible for
the risk assesment or conclusions based on this.
Always, keep focus on the client when using
VENDLET Standard.
Remember to leave the hand control on the
outside of the bed before leaving the client.
PART 2 - User manual
13
7. Then shi the le leg parallel above the right leg.
Moving from one side of the bed to the other
VENDLET Standard may also be used to move clients to the
side of the bed.
In many situaons, this will give the caregiver a beer work
posture, for example in connecon with examinaons, train-
ing, care tasks, dressing, etc.
Moving the client to the edge also improves the contact with
the client.
1. Turn VENDLET Standard on by double clicking the
buon.
2. Press the and buon to to lower the bars if they
have been raised.
3. If necessary, press once or twice on the buon to
reduce speed.
4. Press the or buon on the hand control to move
the client to the side towards you.
8. The client now lies on his/her right side.
9. Press the and buon to slacken the sheet before
the client is le unaended in the bed.
The red bar does not necessarily have to be raised. But if this
makes the client or the caregiver feel safer, the red bar could
be raised during the process.
5. When your work is done, press the or buon to
reposion the client to the middle of the bed.
6. Press the and buon to slacken the sheet before
the client is le unaended in the bed.
Watch a video on how to turn a client
on our webpage www.vendlet.com
or scan the QR-code.
Watch a video on how to transfer a client sideways
on our webpage www.vendlet.com
or scan the QR-code.
PART 2 - User manual
14
Reposioningtheclientupinthebed
It is a well-known problem that clients oen slide down to the
foot end, for example when the back support has been raised
– even if the knee break on the bed was acvated before the
back support.
Typically, when a client slides towards the foot end, the turning
sheet follows the body of the client. In such situaons, you
may use VENDLET Standard to move the client up in the bed
again.
Work in a zig zag paern moving the client diagonally from
side to side of the bed pulling the turning sheet on to the bar,
whilst guiding the sheet to the upper end of the bar.
1. Turn VENDLET Standard on by double clicking the
buon.
2. Press the and buon to to lower the bars if they
have been raised.
3. If necessary, press once or twice on the buon to
reduce speed.
4. Stand next to the headboard and press the buon to
slacken the turning sheet.
5. Gently guide the turning sheet to the upper end of the
blue bar while pressing the buon to pull the client to
the side of the bed.
6. Stop when the client reaches the side of the bed and
repeat the procedure on the opposite side.
7. Connue this process unl the client has been reposi-
oned up in the bed.
8. Press the and buon to slacken the sheet before
the client is le unaended in the bed.
Watch a video on how to reposion a
client higher up in bed
on our webpage www.vendlet.com
or scan the QR-code.
PART 2 - User manual
15
Applying a sling
It is easy to apply a sling on the client when VENDLET Standard
is used.
1. Turn VENDLET Standard on by double clicking the
buon.
2. If necessary, press once or twice on the buon to
reduce speed.
3. Use the turning funcon of VENDLET Standard to move
the client onto his/her side.
4. Place the sling along the back of the client and make sure
that the sling is centred and correctly placed in accordance
with the instrucons of the sling manufacturer.
5. Use the VENDLET Standard turning funcon to move the
client onto his/her back again.
7. Place all straps in such a way that they are ready to be
placed on the liing beam of the hoist.
6. Free the straps on the opposite side.
Watch a video on how to apply a sling
on our webpage www.vendlet.com
or scan the QR-code.
PART 2 - User manual
16
2. Turn VENDLET Standard on by double clicking the
buon.
3. Press the buon to raise the blue bar.
4. If necessary, press once or twice on the buon to
reduce speed.
5. Press the buon to wind the turning sheet onto the
blue bar. VENDLET Standard now turns the client. Hold
your hands on the client’s shoulder and hip to provide a
sense of safety during the procedure. Gently support the
client as he/she is being turned to prone posion.
6. Check that the clients head is comfortable and that there
is room for breathing.
7. To return to a supine posion, press the buon to
raise the red bar and press the buon to wind the tur-
ning sheet onto the red bar. VENDLET Standard now turns
the client to supine posion.
8. Press the and buons to slacken the sheet before
the client is le unaended in the bed.
Proneposion
VENDLET Standard can also be used to turn a client to a prone
posion.
1. Place the client’s right arm closely along his/her body
with the palm of the hand facing the hip. Move the pillow
and place it close to the right upper arm so that the client
comes to lie with his chest on top of the pillow.
Watch a video on how to prone a client on our
webpage www.vendlet.com
or scan the QR-code.
PART 2 - User manual
17
Side rail
If it is assessed that the client must use side rails, VENDLET
Standard has integrated side rails.
1. Press the and buon to raise the bar to the
highest posion
2. Press the and buons to slacken the sheet before
the client is le unaended in the bed.
See page 26 for further informaon on side rail dimensions.
Watch a video on how VENDLET Standard works
as a side rail on our webpage www.vendlet.com
or scan the QR-code.
VENDLET Standard does not interfere with the funconality of
the bed. Slacken the turning sheet suciently before raising
the back, thigh, and/or foot part of the bed.
Under normal circumstances, the bed surface must be level
before you use VENDLET Standard.
In some situaons, however, it may be advantageous to use
the back or foot part of the bed when moving or turning cli-
ents. For example, if the client has wide hips and frail shoul-
ders, he/she will rest more comfortably on the bed if the head
and foot parts are raised a lile before the process.
VENDLET Standard does not reduce the eect of either
pressure-relieving maresses or alternang air maresses.
Pressure measurements have been performed which unambig-
uously show that VENDLET Standard does not have a negave
impact on the pressure-relieving properes of the maresses.
To prevent interference with the funcon of alternang air
maresses, the turning sheet must be suciently slackened
before a client is le unaended in the bed.
At the same me, the velcro strap on the slide sheet must not
be fastened too ghtly on to maress support plaorm, see
page 18.
We recommend that alternang air maresses are rmly in-
ated before paent handling as this brings higher comfort to
the client during the process.
VENDLET Standard can also be used for clients using incon-
nence sheets. The inconnence sheet should have a minimum
width of 125 cm so that it can follow the client’s movements
during turning. You should not use two small inconnence
sheets as the client in this case will lie on a double edge, which
increases the risk of developing pressure ulcers.
The inconnence sheet must not be wrapped around the bars,
but instead must hang loosely out over the bars.
If the client has a catheter or a drainage tube, it may be neces-
sary to adjust the tubes, etc. individually.
Placing the urine bag or drainage tube at the foot end will of-
ten be an opmal soluon. Should this not be possible, howev-
er, you could use long tubes to hang the urine bag or drainage
bag on the outer surface of VENDLET Standard.
In such cases, the bag should be placed on the lowest support
bar on the side rail by the foot board. Route the tube out be-
tween the corner post and the side rail support bars. Be careful
to avoid squeezing the tube.
PART 2 - User manual
18
Place a slide sheet directly on top of the maress, followed by
the turning sheet which is then aached to the two bars.
Slide sheets and turning sheets are available for standard bed
sizes and oponally with increased width which makes VEND-
LET Standard suitable for wider beds as well.
Slide sheet width Fits maress widths Fits maress lenght
95 cm (regular size) 80 - 90 cm 205 cm
95 cm - long 80 - 90 cm 220 cm
115 cm 95 - 110 cm 205 cm
115 cm - long 95 - 110 cm 220 cm
135 cm 110 - 130 cm 205 cm
Turning sheet width Fits maress widths
270 cm (regular size) 80 - 100 cm
320 cm 100 - 130 cm
1. Fold the slide sheet corner elasc straps around the mat-
tress. Check that the surface is smooth and even without
folds. Make sure that the slippery side is facing upwards.
2. Fasten the velcro straps around the edge of the maress
support plaorm. It is important that the straps are fas-
tened around the edge of the plaorm under the maress
and not around the bed frame as this will prevent the
back, thigh, and foot parts of the bed from being raised.
The straps are long enough for thick maresses.
The slide sheet is subject to extensive wear and must be
checked regularly. The fricon of the turning sheet against the
maress will increase if the bed is not ed with a slide sheet
or the slide sheet has been damaged. That will reduce the
comfort of the client during moving and handling.
When an alternang air maress is ed with a slide sheet, it
is important that the velcro straps are not fastened too ghtly
around the edge of the maress support plaorm as this could
interfere the funcon of the alternang air maress. Conse-
quently, the maress should be fully inated while ng the
slide sheet.
PART 2 - User manual
19
Aachingtheturningsheetbeforeuse
1. Place the turning sheet in the middle of the bed.
2. Press the edge strip of the turning sheet into the groove on
one of the bars; begin at the head end of the bed and work
your way down to the foot end.
3. The turning sheet must always be placed OVER the bars to
prevent ngers, hair etc. of the client from geng caught
under the sheet. If the sheet is placed under the bars, the
pulling power will be reduced and the motors will switch
o when the turning sheet is pulled in by the bar.
4. Press the or buon on the hand control and
allow approx. two-thirds of the sheet to be pulled in by
the bar.
5. Press the edge strip at the opposite edge of the turning
sheet into the groove on the other bar.
6. Use this bar to pull in the turning sheet by pressing the
or , buon unl the sheet covers the maress
evenly with the red line at the centre of the maress.
What should I do if the turning sheet is rolled askew on the
bars?
Occasionally, the turning sheet will roll askew on the bars. As
such, this is insignicant and VENDLET Standard will sll be
operable.
This could result in creases in the turning sheet under the cli-
ent which is undesirable. Hence, we recommend that you aim
to smooth the turning sheet if the sheet is askew by more than
a hand’s width on the bars.
In this situaon, you will have to slacken the sheet that has
been pulled askew and pull it in again while guiding / smooth-
ing it with your hand.
Watch a video on how to aach the sheets
on our webpage www.vendlet.com
or scan the QR-code.
PART 2 - User manual
20
Changingtheturningsheetonanoccupiedbed
1. Posion the client on his/her side and then move him/her
to the centre of the bed.
2. Remove the old turning sheet from the bar facing the back
of the client and fold the sheet in layers or roll it. Tuck it
underneath the client.
3. Aach the new turning sheet to the bar and press or
buon to roll the new turning sheet onto the bar.
5. Use the opposite bar to move the client to a supine posi-
on on top of the new and the old turning sheets.
4. Allow approx. half of the new turning sheet to roll onto
the bar and stop when the red line on the sheet is at the
centre of the maress. Fold the remaining part of the new
turning sheet in layers or roll it. Tuck it under the turning
sheet being replaced.
6. Remove the old turning sheet and aach the replacement
sheet to the bar.
Watch a video on how to change the sheet on an occupied bed
on our webpage www.vendlet.com
or scan the QR-code.
Other manuals for STANDARD
1
This manual suits for next models
1
Table of contents
Other Vendlet Medical Equipment manuals
Vendlet
Vendlet V5S Speed Adjust User manual
Vendlet
Vendlet BASIC User manual
Vendlet
Vendlet STANDARD User manual
Vendlet
Vendlet V5 User manual
Vendlet
Vendlet Lejrelet Oval User manual
Vendlet
Vendlet V5S Speed Adjust User manual
Vendlet
Vendlet BASIC User manual
Vendlet
Vendlet V5 User manual
Vendlet
Vendlet V5 Guide
Vendlet
Vendlet V5S Speed Adjust User manual
Popular Medical Equipment manuals by other brands
Novametrix Medical Systems
Novametrix Medical Systems OXYPLETH 520A Service manual
touch bionics
touch bionics i-limb digits user manual
Siemens
Siemens MOBILETT Plus Service instructions
Blatchford
Blatchford LINX22L1S Clinician manual
PerSys Medical
PerSys Medical Waismed BiG user manual
bort medical
bort medical 022 500 SP quick guide