Vendlet BASIC User manual
VALUE IN CARING
MANUAL
BASIC
Vendlet ApS hereby declare that the devices menoned below comply with the Medical Device
Regulaon (EU) 2017/745.
Legal manufacturer: Vendlet ApS, Egelund 33, 6200 Aabenraa, DK
Device: Product no. and name
6200000 VENDLET Basic
UDI-DI:
05714038001056
Basic UDI-DI: 05714038001049EU
Descripon: Electromechanical turning aid for handling and turning paents
in bed.
Classicaon, rule: Class I acc. to rule 1 and 13 of annex VIII in (EU) 2017/745.
The product complies with the
following standards:
EN 60601-2-52:2010 Medical electrical equipment – Part 2-52:
Parcular requirements for basic safety and essenal perfor-
mance of medical beds
60601-1-2:2015 Medical electrical equipment. General require-
ments for basic safety and essenal performance - Collateral
Standard: Electromagnec disturbances - Requirements and test
EN 60529+A1:2002 Degree of protecon provided by enclosures
(IP Code) - Washability
This declaraon of conformity is valid from the date of signature.
Aabenraa, 29.10.2020
Peter Maindal
Director
Congratulaons on your new VENDLET.
The VENDLET is used for handling bedridden clients, for exam-
ple:
• turning the client to lateral, prone or supine posions
• moving the client from one side of the bed to the other
• reposioning the client up in the bed
This manual covers the VENDLET Basic.
Max. user weight is 150 kg
The instrucons in this manual must be followed. Vendlet
ApS shall not be liable should the VENDLET Basic be used,
modied, or assembled in a way that is not described in this
manual.
This manual is divided into three parts:
Part 1 contains general informaon that is useful to everyone
responsible for the purchasing, examinaon, use, assembly,
and maintenance of the VENDLET Basic.
Part 2 is a user manual containing informaon about the oper-
aon and daily maintenance of the VENDLET Basic.
Part 3 is a technical manual containing informaon about the
assembly, maintenance, and service of the VENDLET Basic.
Independent living 7
Sta7
Environment 7
Turning 12
Moving from one side of the bed to the other 13
Reposioningtheclientupinthebed 14
Applying a sling 15
Proneposion 16
Side rail 17
Toolsandbolts 26
Dimensionalrequirements,siderails 26
Maximum loads 27
Aachingaside 27
Height adjustment 29
Mounngthecontrolunit 30
Connecngthecontrolunit 31
Connecngthepowercables 32
Aachingtheturningsheetbeforeuse 19
WhatshouldIdoiftheturningsheetisrolledaskewonthebars? 19
Changingtheturningsheetonanoccupiedbed 20
Cleaningofelectricalandmechanicalparts 23
Washinginstrucons,slidesheet 23
Washinginstrucons,turningsheet 23
Electricalparts 35
Mechanicalparts 35
Sheets 35
Funconaltests 35
Rechargingduringstorage 37
LEDfunconality 37
Buzzerfunconality 37
PART 1 - General information
7
VENDLET Basic may be used for moving clients to a lateral,
prone, or supine posion, from one side of the bed to the
other, or, to reposion them further up in bed.
VENDLET Basic protects the caregiver from physical strain
and heavy liing in connecon with the handling of immobile
clients. Clients are turned/handled by pressing a hand control
whereby the caregiver may support the client and ensure their
correct and comfortable posioning. This provides room for
increased awareness in the care, which boosts employee job
sasfacon and client well-being.
To the client, the turning process becomes uniform and steady
as the sheet supports the body over its full length.
The target group is adult clients who are being cared for,
dressed, washed etc. in bed. This will oen be clients who are
lied in and out of bed or clients who are mobilized using a
standing aid. Hence, the user will typically be clients with few
physical and/or cognive resources and palliave clients.
VENDLET Basic is also suitable for clients at risk of developing
pressure ulcers. The uniform and steady transfer with the
sheet minimizes fricon and the associated shear that can
damage the ssue and cause pressure ulcers. Furthermore,
VENDLET Basic is oen seen to have a posive eect on clients
suering from spaal awareness.
The VENDLET Basic is intended for adult clients weighing
between 0 and 150 kg, with a height above 146 cm and a body
mass index (BMI) above 17.
Prior to the rst use of the VENDLET, it is important to assess
whether VENDLET Basic is suitable for the client in queson. It
may be necessary to take special precauons, for example if a
client is very restless in bed or has an untypical anatomy.
Independent living
VENDLET Basic is not designed to be operated by the clients
themselves. However, if a risk assessment made by the respon-
sible healthcare professional evaluate, that the client is able
to take part in the moving and handling procedures, e.g. by
operang the hand control, this can be a part of the rehabilita-
ve eort.
The risk assessment should evaluate the clients physical,
cognive and palliave resources. The risk assessment must be
available by the bed and must be updated on a regular basis.
Vendlet cannot be held responsible for the risk assessment or
conclusions based on this.
Sta
Before using VENDLET Basic, it must be ensured that the car-
egivers/operators have read “Part 2 – User manual” and that
the manual and quick guide are available by the bed.
Environment
VENDLET Basic can be used in all applicaon environment
(1-5), e.g. hospitals, nursing homes and domesc / private
homes.
VENDLET Basic consist of two bars ed with motors. The bar
on the le side of the client has a blue color marking and the
bar on the right side of the client has a red color marking.
Each motorized bar has a groove which makes it possible to at-
tach the edge strip of the turning sheet to the bars. When the
bars are running, the turning sheet will be dragged between
the two bars, making it possible to move it from side to side.
A slide sheet is inserted under the turning sheet in order to
reduce the fricon of the turning sheet against the maress.
The bars are raised manually by liing the bar unl the corner
post clicks leaving the bar locked in the upper posion. The bar
can be raised one end at the me or simultaneously by a grip
on the middle of the bar.
The bars are lowered manually by liing the end of the bar
while clicking the grey buon at the top of the corner post.
This releases the bar which can now be lowered.
To allow the individual adjustment of VENDLET Basic to
any bed and maress, the mounng brackets are height-
adjustable.
Furthermore, VENDLET Basic consist of a control unit and a
hand control. The control unit is placed underneath the bed,
normally on the base frame.
When the bars are raised VENDLET Basic works as side rails.
VENDLET Basic is telescopic in length and can be extended
from 200 to 220 cm.
PART 1 - General information
8
Red corner post
Head end
Red corner post
Foot end
Blue corner post
Head end
Blue corner post
Foot end
Turning sheet
Blue bar
Red bar
VENDLET Basic
The bars on the VENDLET Basic turn together. If the red bar
pulls, the blue bar starts slackening, and vice versa. If you don’t
want the sheet to be slackened at the opposite bar, press both
+ simultaneously or + simultaneously.
VENDLET Basic is switched on by double-clicking the on
the hand control. VENDLET Basic produce a “beep” upon ac-
vaon and the green diode over the power symbol turns on.
When VENDLET Basic hasn’t been used for 90 seconds, the
system produces a “beep-beep” sound, the diode turns o,
and then VENDLET Basic is turned o.
When VENDLET Basic is turned on, the bars can be turned in
both direcons. The colour coding on the bars relates to the
colours on the hand control buons.
Press and hold the individual buons long enough to obtain
the desired operaon; the motors will stop when the buon
is released. Likewise, you may stop an acvated funcon by
clicking the .
VENDLET Basic hand control
* If there is an acousc alarm, reset the system by simultaneously press-
ing the two top buons on the hand control. You will hear 10 rhythmic
beeps. Press and hold the buons unl the beeping stops.
Tighten the sheet
on the blue bar
Slacken the sheet
on the blue bar
Tighten the sheet
on the red bar
Slacken the sheet
on the red bar
Power with
light / stop buon
Roll the sheet on
the red bar without
slackening the sheet
on the blue bar by
pressing +
simultaneously
Roll the sheet on
the blue bar without
slackening the sheet
on the red bar by
pressing +
simultaneously
Reset*
Watch a vidoe on how the hand control works
on our webpage www.vendlet.com
or scan the QR-koden.
Height
adjustment
Grey release
buon
PART 1 - General information
9
When the bar is up on the side where the turning sheet is be-
ing ghtened, the client will be turned. If, on the other hand,
the bar is down on the side where the turning sheet is being
ghtened, the client will be moved towards the edge of the
bed. These fundamental principles provide you with a number
of ways to move and/or transfer clients. See the “How to Use
the VENDLET” secon in “Part 2 – User Manual” for further
details.
VENDLET Basic can be operated by only one caregiver.
As it is recommended that the client does not
operate VENDLET Basic themselves, the hand
control must be placed on the outside of the bed
before leaving the client.
The client must not operate VENDLET Basic on
their own unless a qualied risk assessment has
been carried out. Vendlet ApS cannot be held
responsible for the risk assesment or conclusions
based on this.
Always, keep focus on the client when using
VENDLET Basic.
If the client has long and loose hanging hair, the
hair could in some situaons be rolled onto the
bar. Therefore, long loose hair should be collect-
ed before moving and handling the client.
Be aware, that the client does not get too close
to the edge of the bed, as there is a risk of falling
out of the bed.
Do not use VENDLET Basic if the bars can not be
elevated properly.
Lowering the bed to a very low posion may
leave the corner post close to the oor.
Consequently, you should not place your feet
under the corner posts.
The client must not hold on to the edge of the
turning sheet or bar during the transfer. If the
client is restless and needs something to hold on
to, we recommend they get a handle such as a
MANULET Mono Grip.
The power buon also funcons as a stop
buon.
If the hand control buon controlling the ght-
ening of the sheet fails, the operaon can be
stopped by pressing the buon.
Addional hand control:
An addional hand control can be connected if a hand control
is required on both sides of the bed.
Wider sheets:
Wider turning sheets and slide sheets are also available if
VENDLET Basic is to be used on wider beds.
Baery backup:
Baery backup is available to operate VENDLET Basic without
a connecon to the supply network. See page 37 for technical
informaon on the baery backup.
PART 1 - General information
10
VENDLET Basic is intended for mounng on a wide range of
hospital and care beds and with a wide range of maresses.
The following bed and maress requirements must be met.
The bed must meet the EN 60601-2-52 standard or the expired
EN 1970 or EN 60601-2-38 standards.
The bed must have a square steel frame (dimensions H 45-78
mm, W min. 20 mm, L min. 1840 mm) without protrusions.
Inner distance between the head- and foot board must be at
least 201 cm. The bed width is not crucial as extra wide turning
sheets and slide sheets are available.
VENDLET Basic can be mounted on most beds with these
dimensions. But situaons where VENDLET Basic cannot be
mounted can occur.
The maximum user weight and safe working load
of the bed must not be exceeded following the
installaon of VENDLET Basic, see page 27.
The maress must meet the requirements of the
bed manufacturer and be suitable for the bed.
The maximum user weight specicaon of the maress must
not be exceeded.
Following the mounng of the VENDLET Basic,
the distance between the maress sides and side
rails must be minimum 2.5 cm and maximum 4
cm, see page 26.
If the maress is so and easily compressible,
it must be ensured that there is no entrapment
hazard due to extra compression at the edge of
the maress.
When alternang air maresses are used, it should be possible
to inate the maress to a rm state before VENDLET Basic is
operated. So maresses will increase the fricon against the
maress and create an uneven base which will be uncomforta-
ble for the client when VENDLET Basic is operated.
If the client changes maress, the VENDLET
installaon must be evaluated. A new maress
might change the condions and necessitate the
reinstallaon of VENDLET Basic to reduce the risk
of entrapment.
Vendlet ApS provides a 2-year factory warranty on VENDLET
Basic. The warranty is void if the product is not used,
handled and maintained in accordance with the guidelines in
this manual. Opening the control unit, the bar, the corner post,
or the hand control will also void the warranty.
The warranty does not include the sheets.
The VENDLET Basic service life is 10 years. The service life may
be signicantly extended if the product is used and handled
with care and maintained in accordance with the guidelines in
this manual.
The VENDLET Basic must be serviced annually by a person with
relevant training, see page 35.
In case of an adverse event or a near-accident involving VEND-
LET Basic, the accident must be reported to the competent
authority in the country in which the accident happened and
to the Danish Health and Medicines Authority.
Likewise, Vendlet ApS must also be informed on phone
+45 9631 0050 or vendlet@vendlet.dk.
PART 1 - General information
11
The product complies with the
Medical Device Regulaon (EU) 2017/745
MD This product is a medical device
Legal manufacturer
Date of manufacture
Serial number
Item no. / Catalogue number: 7 digits
Consulng the manual is mandatory
Warning triangle indicates when special aenon is nec-
essary
For indoor use
This product is a class ll equipment (IEC 61140)
The product is a type B equipment according to EN 60601-1
Max. user weight
Electronic scrap. When disposing of the products,
sub-components should be recycled
IPX6w This product is washable
U In:100-
240VAC,
50/60Hz
The mains voltage must be 100-240 V AC.
200 W Max power consumpon is 200 W
(SMPS: Switch mode power supply).
I In:
max.3,9A The current used is max 3,9 A
Int.:10% -
2/18min on/o
The system should only be used 10% of the me. Aer 2
min of connuous use it requires 18 min rest.
Max 200W/80
sec./
100W/40sec
@25˚C
In connuous use at 25˚C 200 W can be supplied for 80
sec - then the power consumpon will be reduced to 100
W for 40 sec.
0
+50
This product must be stored between 0 and 50°C
5
40°C
This product must be used between 5 and 40˚C
20
90%
This product must be stored between 20 and 90% humidity
at 30°C
Keep dry (when stored)
Rev. Revision no. of the label
Power / stop buon
Tighten the sheet on the red or blue bar
Slacken the sheet on the red or blue bar
The hand control and the control unit complies with the EMC
Direcve 2014/30/EU and the Low Voltage Direcve 2014/35/
EU
The component complies with the EMC regulaon of Australia
and New Zealand.
The component complies with China RoHS.
Type + item Product no/catalogue no
Date Date of producon
W/O Work order
The product / system label is placed on the corner posts at the foot end.
PART 2 - User manual
12
5. Immediately aer this, guide the right arm of the client to
the side.
7. The client now lies on his/her right side.
8. Press the and buon to slacken the sheet before
the client is le unaended in the bed.
The red bar does not necessarily have to be raised. But if this
makes the client or the caregiver feel safer, the red bar could
be raised during the process.
6. Then shi the le leg in parallel above the right leg.
OPERATION
The turning sheet on VENDLET Basic can only be operated with
the hand control. The turning motors lock in posion when not
used.
The bars are raised and lowered manually. During operaon,
the bars must always be horizontal in the highest or lowest
posion.
Remember to slacken the turning sheet by pressing the or
buon before raising the bar.
Should the turning sheet be too loose on one side, you can
ghten the sheet by pressing + simultaneously or
+ simultaneously.
Always, keep focus on the client when using
VENDLET.
Remember to leave the hand control on the
outside of the bed before leaving the client.
Turning
VENDLET Basic may be used to turn clients. Follow this proce-
dure to move a client from a supine posion to lying on his/her
right side.
1. Turn VENDLET Basic on by double clicking the buon.
Press the buon to slacken the turning sheet.
2. Raise the blue bar by liing unl it locks in both corner
posts.
3. Press the buon to ghten the turning sheet on the
blue bar.
4. Place the le arm of the client on his/her stomach or chest
the moment before he/she starts turning. Watch a video on how to turn a client
on our webpage www.vendlet.com
or scan the QR-code.
PART 2 - User manual
13
1. Lower the bars if they are raised: Li the bar and press the
grey buon on the corner post. When it is released you
can lower the foot end of the bar.
Moving from one side of the bed to the other
VENDLET Basic may also be used to move clients to the side of
the bed.
In many situaons, this will give the caregiver a beer work
posture, for example in connecon with examinaons, train-
ing, care tasks, dressing, etc.
Moving the client to the edge also improves the contact with
the client.
2. Do the same at the head end.
5. When your work is done, press the or buon to
reposion the client to the middle of the bed.
6. Press the and buon to slacken the sheet before
the client is le unaended in the bed.
3. Turn VENDLET Basic on by double clicking the buon.
4. Press the or buon on the hand control to move
the client to the side towards you.
PART 2 - User manual
14
Reposioningtheclientupinthebed
It is a well-known problem that clients oen slide down to the
foot end, for example when the back support has been raised
– even if the knee break on the bed was acvated before the
back support.
Typically, when a client slides towards the foot end, the turning
sheet follows the body of the client. In such situaons, you
may use VENDLET Basic to move the client up in the bed again.
Work in a zig zag paern moving the client diagonally from
side to side of the bed pulling the turning sheet on to the bar,
whilst guiding the sheet to the upper end of the bar.
1. Lower the bars if they are raised.
2. Turn VENDLET Basic on by double clicking the buon.
3. Stand next to the headboard and press the buon to
slacken the turning sheet on the blue bar.
4. Gently guide the turning sheet to the upper end of the
blue bar while pressing the buon to pull the client to
the side of the bed.
5. Stop when the client reaches the side of the bed and
repeat the procedure on the opposite side.
6. Connue this process unl the client has been reposi-
oned up in the bed.
7. Press the and buon to slacken the sheet before
the client is le unaended in the bed.
Watch a video on how to reposion a
client higher up in bed
on our webpage www.vendlet.com
or scan the QR-code.
PART 2 - User manual
15
Applying a sling
It is easy to apply a sling on the client when VENDLET Basic is
used.
1. Turn VENDLET Basic on by double clicking the buon.
2. Use the turning funcon of the VENDLET system to move
the client onto his/her side.
3. Place the sling along the back of the client and make sure
that the sling is centred and correctly placed in accordance
with the instrucons of the sling manufacturer.
4. Use the VENDLET turning funcon to move the client onto
his/her back again.
6. Place all straps in such a way that they are ready to be
placed on the liing beam of the hoist.
5. Free the straps on the opposite side.
Watch a video on how to apply a sling
on our webpage www.vendlet.com
or scan the QR-code.
PART 2 - User manual
16
2. Turn VENDLET Basic on by double clicking the buon.
Press the buon to slacken the turning sheet.
3. Raise the blue bar by liing unl it locks in both corner
posts.
4. Press the buon to wind the turning sheet onto the
blue bar. The VENDLET system now turns the client. Hold
your hands on the client’s shoulder and hip to provide a
sense of safety during the procedure. Gently support the
client as he/she is being turned to prone posion.
5. Check that the clients head is comfortable and that there
is room for breathing.
6. To return to a supine posion, raise the red bar and press
the buon to wind the turning sheet onto the red bar.
The VENDLET now turns the client to supine posion.
7. Press the and buons to slacken the sheet before
the client is le unaended in the bed.
Proneposion
VENDLET Basic can also be used to turn a client to a prone
posion.
1. Place the client’s right arm closely along his/her body
with the palm of the hand facing the hip. Move the pillow
and place it close to the right upper arm so that the client
comes to lie with his/her chest on top of the pillow.
Watch a video on how to prone a client on our
webpage www.vendlet.com
or scan the QR-code.
PART 2 - User manual
17
Side rail
If it is assessed that the client must use side rails, VENDLET
Basic has integrated side rails.
1. Press the and buons to slacken the turning sheet.
Raise the bars by liing unl it locks in both corner posts
2. Press the and buons to slacken the sheet before
the client is le unaended in the bed.
3. Should the turning sheet be too loose on one side, you can
ghten the sheet by pressing + simultaneously or
+ simultaneously.
See page 26 for further informaon on side rail dimensions.
VENDLET Basic can also be used for clients using inconnence
sheets. The inconnence sheet should have a minimum width
of 125 cm so that it can follow the client’s movements during
turning. You should not use two small inconnence sheets as
the client in this case will lie on a double edge, which increases
the risk of developing pressure ulcers.
The inconnence sheet must not be wrapped around the bars,
but instead must hang loosely out over the bars.
If the client has a catheter or a drainage tube, it may be neces-
sary to adjust the tubes, etc. individually.
Placing the urine bag or drainage tube at the foot end will of-
ten be an opmal soluon. Should this not be possible, howev-
er, you could use long tubes to hang the urine bag or drainage
bag on the outer surface of VENDLET Basic.
In such cases, the bag should be placed on the lowest support
bar on the side rail by the foot board. Route the tube out be-
tween the corner post and the side rail support bars. Be careful
to avoid squeezing the tube.
VENDLET Basic does not interfere with the funconality of the
bed. Slacken the turning sheet suciently before raising the
back, thigh, and/or foot part of the bed.
Under normal circumstances, the bed surface must be level
before you use VENDLET Basic.
In some situaons, however, it may be advantageous to use
the back or foot part of the bed when moving or turning cli-
ents. For example, if the client has wide hips and frail shoul-
ders, he/she will rest more comfortably on the bed if the head
and foot parts are raised a lile before the process.
VENDLET Basic does not reduce the eect of either pres-
sure-relieving maresses or alternang air maresses.
Pressure measurements have been performed which unam-
biguously show that VENDLET Basic does not have a negave
impact on the pressure-relieving properes of the maresses.
To prevent interference with the funcon of alternang air
maresses, the turning sheet must be suciently slackened
before a client is le unaended in the bed.
At the same me, the velcro strap on the slide sheet must not
be fastened too ghtly on to the maress support plaorm,
see page 18.
We recommend that alternang air maresses are rmly in-
ated before paent handling as this brings higher comfort to
the client during the process.
Watch a video on how VENDLET Basic works
as a side rail on our webpage www.vendlet.com
or scan the QR-code.
PART 2 - User manual
18
Place a slide sheet directly on top of the maress, followed by
the turning sheet which is then aached to the two bars.
Slide sheets and turning sheets are available for standard bed
sizes and oponally with increased width which makes VEND-
LET Basic suitable for wider beds as well.
Slide sheet width Fits maress widths Fits maress lenght
95 cm (regular size) 80 - 90 cm 205 cm
95 cm - long 80 - 90 cm 220 cm
115 cm 95 - 110 cm 205 cm
115 cm - long 95 - 110 cm 220 cm
135 cm 110 - 130 cm 205 cm
Turning sheet width Fits maress widths
270 cm (regular size) 80 - 100 cm
320 cm 100 - 130 cm
1. Fold the slide sheet corner elasc straps around the mat-
tress. Check that the surface is smooth and even without
creases and folds. Make sure that the slippery side is
facing upwards.
2. Fasten the velcro straps around the edge of the maress
support plaorm. It is important that the straps are fas-
tened around the edge of the plaorm under the maress
and not around the bed frame as this will prevent the
back, thigh, and foot parts of the bed from being raised.
The straps are long enough for thick maresses.
The slide sheet is subject to extensive wear and must be
checked regularly. The fricon of the turning sheet against the
maress will increase if the bed is not ed with a slide sheet
or the slide sheet has been damaged. That will reduce the
comfort of the client during moving and handling.
When an alternang air maress is ed with a slide sheet, it
is important that the velcro straps are not fastened too ghtly
around the edge of the maress support plaorm as this could
interfere the funcon of the alternang air maress. Conse-
quently, the maress should be fully inated while ng the
slide sheet.
PART 2 - User manual
19
Aachingtheturningsheetbeforeuse
1. Place the turning sheet in the middle of the bed
2. Press the edge strip of the turning sheet into the groove
on one of the bars; begin at the head end of the bed and
work your way down to the foot end.
WhatshouldIdoiftheturningsheetisrolledaskewonthe
bars?
Occasionally, the turning sheet will roll askew on the bars. As
such, this is insignicant and VENDLET Basic will sll be opera-
ble.
This could result in creases in the turning sheet under the cli-
ent which is undesirable. Hence, we recommend that you aim
to smooth the turning sheet if the sheet is askew by more than
a hand’s width on the bars.
In this situaon, you will have to slacken the sheet that has
been pulled askew and pull it in again while guiding / smooth-
ing it with your hand.
3. The turning sheet must always be placed OVER the bars to
prevent ngers, hair etc. of the client from geng caught
under the sheet. If the sheet is placed under the bars, the
pulling power will be reduced, and the motors will switch
o when the turning sheet is pulled in by the bar.
4. Press the or buon on the hand control and allow
approx. two-thirds of the sheet to be pulled in by the bar.
5. Press the edge strip at the opposite edge of the turning
sheet into the groove on the other bar.
6. Use this bar to pull in the turning sheet by pressing the
or , buon unl the sheet covers the maress even-
ly with the red line at the centre of the maress.
7. The bars on the VENDLET Basic turn together. If the red
bar pulls, the blue bar starts slackening, and vice versa. If
you don’t want the sheet to be slackened at the opposite
bar, press both + simultaneously or + simulta-
neously.
Watch a video on how to aach the sheets
on our webpage www.vendlet.com
or scan the QR-code.
PART 2 - User manual
20
Changingtheturningsheetonanoccupiedbed
1. Posion the client on his/her side and then move him/her
to the centre of the bed.
2. Remove the old turning sheet from the bar facing the back
of the client and fold the sheet in layers or roll it. Tuck it
underneath the client.
3. Aach the new turning sheet to the bar and press or
buon to roll the new turning sheet onto the bar.
5. Use the opposite bar to move the client to a supine posi-
on on top of the new and the old turning sheets.
4. Allow approx. half of the new turning sheet to roll onto
the bar and stop when the red line on the sheet is at the
centre of the maress. Fold the remaining part of the new
turning sheet in layers or roll it. Tuck it under the turning
sheet being replaced.
6. Remove the old turning sheet and aach the replacement
sheet to the bar.
Watch a video on how to change the sheet on an occupied bed
on our webpage www.vendlet.com
or scan the QR-code.
Other manuals for BASIC
1
This manual suits for next models
1
Table of contents
Other Vendlet Medical Equipment manuals
Vendlet
Vendlet V5 User manual
Vendlet
Vendlet V5 Guide
Vendlet
Vendlet V5 User manual
Vendlet
Vendlet BASIC User manual
Vendlet
Vendlet V5S Speed Adjust User manual
Vendlet
Vendlet V5S Speed Adjust User manual
Vendlet
Vendlet Lejrelet Oval User manual
Vendlet
Vendlet STANDARD User manual
Vendlet
Vendlet STANDARD User manual
Vendlet
Vendlet V5S Speed Adjust User manual
