Vents TwinFresh R-50 User manual

USER'S MANUAL
TwinFresh R-50
TwinFresh RA-50
TwinFresh R-50-2
TwinFresh RA-50-2
TwinFresh S-60
TwinFresh SA-60
TwinFresh S-60-2
TwinFresh SA-60-2
TwinFresh S1-50
TwinFresh SA1-50
TwinFresh S1-50-2
TwinFresh SA1-50-2
Single-room reversible energy
regeneration ventilator

www.ventilation-system.com
2
Introduction 3
Purpose 5
Delivery set 6
Designation key 7
Main technical parameters 7
Safety requirements 11
Design and operating logic 13
Mounting and set-up 19
Unit connection and control 26
Maintenance 28
Storage and transportation regulations 28
Manufacturer's warranty 29
Acceptance certicate 30
Seller information 30
Installation certicate 30
Warranty card 31
CONTENT

3
• Read the user's manual carefully prior to installing and operating the unit.
• Full the user's manual requirements as well as the provisions of all the applicable local and national construction, electrical and
technical norms and standards.
• The warnings contained in the user's manual must be considered most seriously since they contain vital personal safety information.
• Failure to follow the rules and safety precautions noted in this user's manual may result in an injury or unit damage.
• After a careful reading of the manual, keep it for the entire service life of the unit.
• While transferring the unit control the User's manual must be turned over to the receiving operator.
Symbol legend:
WARNING!
DO NOT!
SAFETY REQUIREMENTS
The user's manual consisting of the technical details, operating instructions and technical specication applies to the installation and
mounting of the single-room energy regeneration reversible ventilator TwinFresh, (hereinafter "the unit" as mentioned in the "Safety
Requirements" and "Manufacturer's Warranty" sections as well as in warnings and information blocks).
UNIT MOUNTING AND OPERATION SAFETY PRECAUTIONS
• Disconnect the unit from power mains prior
to any installation operations. • The unit must be grounded!
• Do not lay the power cable of the unit in
close proximity to heating equipment.
• While installing the unit follow the safety
regulations specic to the use of electric
tools.
• Do not change the power cable length at
your own discretion.
• Do not bend the power cable.
• Avoid damaging the power cable.
• Do not put any foreign objects on the power
cable.
• Unpack the unit with care.
• Do not use damaged equipment or cables
when connecting the unit to power mains.
• Do not operate the unit outside the
temperature range stated in the user's
manual.
• Do not operate the unit in aggressive or
explosive environments.
• Do not touch the unit controls with wet
hands.
• Do not carry out the installation and
maintenance operations with wet hands.
• Do not wash the unit with water.
• Protect the electric parts of the unit against
ingress of water.

www.ventilation-system.com
4
UNIT MOUNTING AND OPERATION SAFETY PRECAUTIONS
• Do not allow children to operate the unit. • Disconnect the unit from power mains prior to
any technical maintenance.
• Do not store any explosive or highly ammable
substances in close proximity to the unit.
• When the unit generates unusual sounds,
odour or emits smoke disconnect it from
power supply and contact the Seller.
• Do not open the unit during operation. • Do not direct the air ow produced by the unit
towards open ame or ignition sources.
• Do not block the air duct when the unit is
switched on.
• In case of continuous operation of the unit
periodically check the security of mounting.
• Do not sit on the unit and avoid placing
foreign objects on it. • Use the unit only for its intended purpose.

5
The unit is designed to ensure continuous mechanical air exchange in houses, oces, hotels, cafes, conference halls and other utility and
public spaces as well as to recover the heat energy contained in the air extracted from the premises to warm up the ltered stream of supply air.
The ventilator is equipped with a ceramic regenerator that enables supply of fresh ltered air heated by means of extract air heat energy
regeneration.
The ventilator is designed for through-the-wall mounting. The telescopic ventilator design enables its installation in the walls with various
thickness, see the table below:
Wall thickness Ventilator model
from 250 mm (9 13/16’’) up to 470 mm (18
1/2”)
• TwinFresh R-50
• TwinFresh RA-50
• TwinFresh RA-50 (120V / 60Hz)
• TwinFresh R-50-1
• TwinFresh RA-50-1
• TwinFresh RA-50-1 (120V / 60Hz)
• TwinFresh R-50-3
• TwinFresh RA-50-3
• TwinFresh RA-50-3 (120V / 60Hz)
• TwinFresh R-50-4
• TwinFresh RA-50-4
• TwinFresh RA-50-4 (120V / 60Hz)
• TwinFresh R-50-5
• TwinFresh RA-50-5
• TwinFresh RA-50-5 (120V / 60Hz)
• TwinFresh S1-50
• TwinFresh SA1-50
• TwinFresh SA1-50 (120V / 60Hz)
from 255 mm (10 1/16’’) up to 475 mm (18
11/16”)
• TwinFresh S-60
• TwinFresh SA-60
• TwinFresh SA-60 (120V / 60Hz)
The unit is rated for continuous operation.
Transported air must not contain any ammable or explosive mixtures, evaporation of chemicals, sticky substances, brous materials,
coarse dust, soot and oil particles or environments favourable for the formation of hazardous substances (toxic substances, dust, pathogenic
germs).
PURPOSE
THE UNIT MAY NOT BE OPERATED BY CHILDREN OR PERSONSWITH REDUCED PHYSICAL,MENTAL OR SENSORY
CAPACITIES, OR LACKING THE APPROPRIATE TRAINING.
THE UNIT MUST BE INSTALLED AND CONNECTED ONLY BY PROPERLY QUALIFIED PERSONNEL AFTER THE
APPROPRIATE BRIEFING.
THE CHOICE OF UNIT INSTALLATION LOCATION MUST PREVENT UNAUTHORIZED ACCESS BY UNATTENDED
CHILDREN.

www.ventilation-system.com
6
Model Control unit Ventilator
Cable, 3 m
long 5xAWG/7
(5x0.25)
User's manual Packing box Mounting kit
TwinFresh R-50

    
TwinFresh RA-50

TwinFresh RA-50 (120V / 60Hz)
TwinFresh R-50-1

TwinFresh RA-50-1

TwinFresh RA-50-1 (120V / 60Hz)
TwinFresh R-50-2
TwinFresh RA-50-2

TwinFresh RA-50-2 (120V / 60Hz)
TwinFresh R-50-3

TwinFresh RA-50-3

TwinFresh RA-50-3 (120V / 60Hz)
TwinFresh R-50-4

TwinFresh RA-50-4

TwinFresh RA-50-4 (120V / 60Hz)
TwinFresh R-50-5

TwinFresh RA-50-5

TwinFresh RA-50-5 (120V / 60Hz)
TwinFresh S1-50

TwinFresh SA1-50

TwinFresh SA1-50 (120V / 60Hz)
TwinFresh S1-50-2

TwinFresh SA1-50-2

TwinFresh SA1-50-2 (120V / 60Hz)
TwinFresh S-60

TwinFresh SA-60

TwinFresh SA-60 (120V / 60Hz)
TwinFresh S-60-2

TwinFresh SA-60-2

TwinFresh SA-60-2 (120V / 60Hz)
DELIVERY SET

7
TwinFresh R1 - 50 - 2 (120 V / 60 Hz)
Ventilation hood type
_ — tapered metal ventilation hood
1— round stainless steel ventilation hood
2— metal ventilation hood for thin walls
3— round plastic ventilation grille
4— rectangular plastic ventilation grille
5 — angular mounting kit
TwinFresh Standard Series
Telescopic air duct cross section
R— round
S— square
Controls availability
Front panel type
_ — ventilation grille
1- panel with a at front cover
Power voltage
_ — 230 V / 50 Hz
120 V / 60 Hz — power voltage 120 V / 60 Hz
Rated air capacity [m/h]
The ventilator is rated for indoor application with the ambient temperature ranging from -20°C (-4 °F) up to +50°C (+122 °F) and relative
humidity up to 80%.
The ventilator is rated as a class I electric appliance.
Ingress Protection (IP) rating from solid objects and liquids IP 24.
The ventilator design is regularly improved, so some models may slightly dier from those ones described in this manual.
TwinFresh R-50
TwinFresh RA-50
TwinFresh S1-50
TwinFresh SA1-50
TwinFresh S-60
TwinFresh SA-60
TwinFresh R-50
(120V / 60Hz)
TwinFresh RA-50
(120V / 60Hz)
TwinFresh S1-50
(120V / 60Hz)
TwinFresh SA1-50
(120V / 60Hz)
TwinFresh S-60
(120V / 60Hz)
TwinFresh SA-60
(120V / 60Hz)
Speed 1 2 1 2 1 2 1 2 1 2 1 2
Supply Voltage [V] 230 V / 50 Hz 120 V / 60 Hz
Power [W] 3,5 4,6 3,5 4,6 2,8 4,8 4,1 7,0 4,25 7,1 3,2 5,4
Current [A] 0,02 0,025 0,02 0,025 0,018 0,028 0,04 0,07 0,04 0,07 0,04 0,06
Air capacity [m3/h] (CFM) 25
(15)
50
(29)
25
(15)
50
(29)
35
(21)
58
(34)
22
(13)
58
(34)
15
(9)
46
(27)
30
(18)
51
(30)
RPM [min-1] 570 1100 570 1100 1150 2100 660 1410 660 1410 1500 2410
Noise level, 1 m [dB(A)] (Sones) 24
(0,5)
34
(1,2)
24
(0,5)
34
(1,2)
34
(1,2)
41
(2,0)
26
(0,6)
36
(1,5)
26
(0,6)
36
(1,5)
36
(1,5)
43
(3,5)
Noise level, 3 m [dB(A)] (Sones) 14
(0,3)
24
(0,5)
14
(0,3)
24
(0,5)
24
(0,5)
29
(0,7)
16
(0,3)
26
(0,5)
16
(0,3)
26
(0,5)
26
(0,5)
31
(0,8)
Noise level [dB(A)] (Sones)* 18
(0,4)
19
(0,4)
19
(0,4)
18
(0,4)
19
(0,4)
19
(0,4)
Max. transported medium temperature [°C (°F)] from -20 (-4 ) up to +50 (122)
Heat regeneration eciency [%] ≤90 ≤88 ≤90 ≤88
Regenerator type Ceramic
Air duct size [mm] (inches) Ø150
(6")
164x164
(6 7/16" x 6 7/16")
164x164
(6 7/16" x 6 7/16")
Ø150
(6")
164x164
(6 7/16" x 6 7/16")
164x164
(6 7/16" x 6 7/16")
* Outdoor sound pressure attenuation is measured by comparing the indoor sound pressure level in an open air duct inside the wall and the indoor sound
level with the ventilator built inside the wall.
DESIGNATION KEY
MAIN TECHNICAL PARAMETERS

www.ventilation-system.com
8
VENTILATOR OVERALL DIMENSIONS MM INCHES
TwinFresh R-50 and TwinFresh RA-50
250 (9 ⁄’’) - 470 (18 ½”)133
(5 ¼")
57
(2 ¼")
300
(11 ⁄")
280
(11")
213
( 8 ⁄")
156
6 ⁄"
TwinFresh R-50-1 and TwinFresh RA-50-1
250 (9 ⁄’’) - 470 (18 ½”)90
(3 ⁄")
57
(2 ¼")
195
( 7 ⁄")
213
( 8 ⁄")
156
6 ⁄"
TwinFresh R-50-2 and TwinFresh RA-50-2
120 (4 ¾’’) - 430 (16 ⁄”)144
(5 ⁄")
57
(2 ¼")
213
( 8 ⁄")
300
(11 ⁄")
310
(12 ⁄")
260
(10 ¼")
156
6 ⁄"
TwinFresh R-50-3 and TwinFresh RA-50-3
250 (9 ⁄’’) - 470 (18 ½”) 57
(2 ¼")
185
( 7 ⁄")
213
( 8 ⁄")
156
6 ⁄"

9
VENTILATOR OVERALL DIMENSIONS MM INCHES
TwinFresh R-50-4 and TwinFresh RA-50-4
250
(9 ⁄")
180
(7 ⁄")
250 (9 ⁄’’) - 470 (18 ½”) 57
(2 ¼")
213
( 8 ⁄")
156
6 ⁄"
TwinFresh R-50-5 and TwinFresh RA-50-5
250 (9 ⁄’’) - 470 (18 ½”)
57
(2 ¼")
232
(9 ⁄")
93
(3 ⁄")
500
(19 ⁄")
60
(6 ⁄")
213
( 8 ⁄")
156
6 ⁄"
TwinFresh S-60 and TwinFresh SA-60
255 (10 ⁄”) - 475 (18 ⁄”)144
(5 ⁄")
34
(1 ⁄")
300
(11 ⁄")
280
(11")
274
( 10 ⁄")
170
( 6 ⁄")

www.ventilation-system.com
10
VENTILATOR OVERALL DIMENSIONS MM INCHES
TwinFresh S-60-2 and TwinFresh SA-60-2
120(4 ¾") - 430 (16 ⁄")144
(5 ⁄")
34
(1 ⁄")
260
(10 ¼")
300
(11 ⁄")
310
(12 ⁄")
274
( 10 ⁄")
170
( 6 ⁄")
TwinFresh S1-50 and TwinFresh SA1-50
250 (9 13/16’’) - 470 (18 1/2”)133
(5 ¼")
56
(2 ⁄")
300
(11 ⁄")
280
(11")
240
( 9 ⁄")
170
( 6 ⁄")
TwinFresh S1-50-2 and TwinFresh SA1-50-2
120(4 ¾") - 430 (16 ⁄")144
(5 ⁄")
56
(2 ⁄")
260
(10 ¼")
300
(11 ⁄")
310
(12 ⁄")
240
( 9 ⁄")
170
( 6 ⁄")
CONTROL UNIT OVERALL DIMENSIONS MM INCHES
82
(3 ¼")
153 (6")
59
(2 ⁄")
44
(1 ¾")

11
The ventilator consists of a telescopic air duct with adjustable length (inner part and outer part), a ventilation unit and an outer ventilation
hood. The inner telescopic part contains one or two air lters, depending on the ventilation model and a ceramic regenerator.
The air lters are designed to purify supply air and prevent foreign object ingress into the regenerator and the fan. The ceramic regenerator
utilises extract air heat energy to warm up supply air ow. The regenerator is equipped with a pull cord inside to facilitate its withdrawal from
the ventilator. The regenerator is installed on an insulating layer used as a sealer as well.
The ventilation unit must be installed on inner side of the wall.
The ventilation unit is equipped with automatic shutters that shut the air duct o during the ventilator standby and prevent air back draft.
TwinFresh S-60 and its modications are not equipped with automatic shutters.
The outer ventilation hood is used to prevent direct ingress of water and other objects to the ventilator.
Outer ventilation hood
Prevents direct ingress of water and foreign
objects into the ventilator.
1. TwinFresh R-50 and its modications
2. TwinFresh S-60 and its modications
3. TwinFresh S1-50 and its modications
Distance ring
It doubles as a support for lters and a
regenerator in the inner telescopic duct.
Filter
Cleans supply air ow and prevents ingress of
dust and foreign objects into the ventilator.
Prevents soiling of the regenerator.
Air ow rectier
Prevents air turbulences and reduces noise
level.
Fan
Generates air ow.
Ventilation unit
Generates air ow by means of the fan. The
ventilation unit is covered with a ventilation
grille on inner wall side to prevent ingress of
foreign objects into the fan. The ventilation
unit is equipped with automatic shutters to
back draft prevention. The air shutters open
during the ventilator activation and close
during its shutdown.
Outer air duct
Outer part of the telescopic air duct.
Ceramic regenerator
Utilises extract air heat energy to warm up
supply air ow.
Inner air duct
Inner part of the telescopic air duct.
Decorative front panel
Used for decoration of the ventilator.
Decorative grille
Protects the ventilator from foreign object
ingress from inside.
Internal lter
Cleans supply air ow and prevents ingress of
dust and foreign objects into the ventilator.
Prevents soiling of the regenerator.
1
3
2
TWINFRESH STRUCTURE
AUTOMATIC SHUTTERS OPERATION
Ventilator is o (the automatic shutters are closed) Ventilator is on (the louver shutters are opened)
DESIGN AND OPERATING LOGIC

www.ventilation-system.com
12
VENTILATOR OPERATION MODES
The ventilator has two ventilation modes:
• Air supply / air extraction. The ventilator operates in air supply or air extract mode with set air speed, see page 20.
• Regeneration. The ventilator operates in reversible mode with heat and humidity regeneration.
A
I
R
E
X
T
R
A
C
T
I
O
N
A
I
R
S
U
P
P
L
Y
CYCLE I
CYCLE II
7
0
s
e
c
.
7
0
s
e
c
.
-10 °С
(+14 °F)
-10 °С
(+14 °F)
+20 °С
(+68 °F)
+20 °С
(+68 °F)
+17 °С
(+63 °F)
-7 °С
(+19.4 °F)
-7 °С
(+19.4 °F)
+17 °С
(+63 °F)
In Regeneration mode the ventilator operates in two cycles, 70 seconds each.
Cycle I. Warm stale air is extracted from the room. As it ows through the regenerator, it heats and moisturizes the regenerator, transferring
up to 90% heat energy. In 70 seconds as the ceramic regenerator gets warmed the ventilator is switched to supply mode.
Cycle II. Fresh intake air from outside ows through the ceramic regenerator and absorbs accumulated moisture and heat up to the room
temperature. In 70 seconds as the ceramic regenerator gets cooled down, the ventilator is switched into extract mode and the cycle is
renewed.

13
MOUNTING OF TWINFRESH R50
1. Prepare a round thorough hole in the outer wall. The hole size in the wall is shown in the gure below.
Ø170
Ø6 ⁄"
min 500
min 19 ⁄"
min 500
min 19 ⁄"
min 500
min 19 ⁄"
( 6 ⁄")
170
A
A-A
A
While mounting several connected in series ventilators provide a recess for the cable layout during the hole preparation to enable
connection of several ventilators in series.
2. Install the telescopic air duct inside the wall. The telescopic air duct end must protrude to the distance A stated below:
Fill the gaps between the wall and the telescopic air duct with a
mounting foam.
MOUNTING AND SETUP
READ THE USER'S MANUAL PRIOR TO MOUNTING THE VENTILATOR.
ATTENTION!
DO NOT BLOCK THE AIR DUCT OF THE INSTALLED VENTILATOR WITH DUST
ACCUMULATING MATERIALS, SUCH AS CURTAINS, CLOTH SHUTTERS, ETC. AS IT
PREVENTS AIR CIRCULATION IN THE ROOM.
BESIDES, THE CURTAINS MAY PREVENT NORMAL AIR CIRCULATION AND REDUCE
THE VENTILATOR PERFORMANCE.

www.ventilation-system.com
14
max A
Outside Inside Ventilator model A [mm] (inches)
TwinFresh R-50 10 (3/8’’)
TwinFresh R-50-1 0 (0’’)
TwinFresh R-50-2 10 (3/8’’)-110(4 5/16’’)
TwinFresh R-50-3 0 (0’’)
TwinFresh R-50-4 0 (0’’)
TwinFresh R-50-5 0 (0’’)
3. Install the lter, the ceramic regenerator, another lter and the air ow rectier in the consecutive order inside the telescopic air duct.
4. Prepare the holes for the dowels 5x25 and insert the dowels. Fix the back part of the ventilation unit on the inner wall by installing the
supplied screws 3x25 into the drilled holes.
97,5
(3 ⁄")
195
(7 ⁄")
6
( ¼")
4 holes
150
(5 ⁄")
75
(2 ⁄")
98
(3 ⁄")
196
(7 ⁄")
5. Cover the ventilation unit with a front panel.
Mark and drill the fastening
holes. Then insert the dowels.

15
MOUNTING OF TWINFRESH S150, TWINFRESH S60 AND MODIFICATIONS
1. Prepare a square thorough hole in the outer wall. The hole size in the wall is shown in the gure below. Prepare two holes for the 5x25
dowels and insert the dowels.
min 500
min 19 ⁄"
min 500
min 19 ⁄"
min 500
min 19 ⁄"
180
7 ⁄"
( 7 1/16")
180
192
(7 9/16")
A
A-A
A
While mounting several connected in series ventilators provide a recess for the cable layout during the hole preparation to enable
connection of several ventilators in series.
2. Install the telescopic air duct inside the wall. The telescopic air duct end must protrude to the distance A stated below:
max A
Outside Inside Ventilator model A [mm] (inches)
TwinFresh S1-50 10 (3/8’’)
TwinFresh S-60 10 (3/8’’)
TwinFresh S1-50-2 10 (3/8’’)-110(4 5/16’’)
TwinFresh S-60-2 10 (3/8’’)-110(4 5/16’’)
Fix the inner part of the telescopic air duct on the inner wall using the
supplied 3x25 screws.
Fill the gaps between the wall and the telescopic air duct with a
mounting foam.

www.ventilation-system.com
16
3. Remove the protecting cardboard part. Install the lter, the ceramic regenerator and the fan in the telescopic air duct. Then perform electrical installations
and lay out the cables in the wall. Install the TwinFresh S1-50 ventilation unit in the same way as TwinFresh R-50 ventilation unit , Page 14.
4. Cover the ventilation unit with a front panel.
OUTER HOOD MOUNTING
1. Mark the fastening holes for the outer ventilation hood and drill holes for the 6x40 dowels. For marking convenience use the ventilation
hood back part.
200 mm
(7 ⁄")
Ø6 mm (¼")
4 holes
220 mm
(8 ⁄")
TwinFresh R-50
194 mm
(7 5⁄8")
Ø6 mm (¼")
4 holes
247 mm
(9 ¾")
TwinFresh R-50-2
200 mm
(7 7/8")
Ø6 mm (¼")
4 holes
220 mm
(8 11/16")
TwinFresh S1-50
TwinFresh S-60
194 mm
(7 5/8")
Ø6 mm (¼")
4 holes
247 mm
(9 3/4")
TwinFresh S1-50-2
TwinFresh S-60-2

17
2. Insert the 6x40 dowels from the delivery set into the holes.
3. Disassemble the outer ventilation hood to enable access to the fastening holes.
Take o the front part of the outer ventilation hood.
1 2
Remove 5 screws and take o the front part of the ventilation hood.
4. Fix the back part of the ventilation hood on the wall with the supplied 4x40 screws from the delivery set.
5. Install the front part of the ventilation hood.

www.ventilation-system.com
18
CONTROL UNIT MOUNTING
1. Prepare a recess in the wall for mounting of the control unit.
Install a junction box in the wall recess.
While mounting the power unit consider the supplied cable length.
A longer cable may be used on customer demand. The
recommended cable type is 5x0.25 (5xAWG/7).
48
1 7/8"
R35 (R 1 3/8")
2 radii
70
2 3/4"
70
2 3/4"
A-A
A
A
Hole spacing for installation of the control unit.
2. Uplift gently the buttons and the end cover of the control unit to
remove.
3. Unlatch and take o the frame of the control unit.
4. Install the control unit in the wall recess.

19
5. Install the frame, the buttons and the end cover in the reverse
order.
The ventilator is operated either via the external control unit KVR-T or KSV- T (included in delivery set of the ventilators supplied with a
control system) or via the control unit KVR (KVS) and the transformer unit TRF 220/12-12 or TRF 220/12-40 (specially ordered accessories).
The ventilator is rated for connection to single-phase ac 230 V/50 Hz
or 120 V/60 power mains, depending on the used transformer type.
The control unit is a three-key switch with an integrated circuit board
and a power transformer (in case of KVR-T and KVS-T only). The control unit
is designed for installation in the junction box.
All electric connection to the control unit and the ventilator are
performed with the socket connectors for mounting and servicing
facilitation. Each mating part of a socket connector has a colour marking in
compliance with marking on the circuit board to ensure correct and quick
electric installation.
CONTROL UNIT
GENERAL VIEW
CONNECTION TO POWER MAINS AND CONTROL
DISCONNECT THE UNIT FROM POWER SUPPLY PRIOR TO ANY ELECTRIC INSTALLATION OPERATIONS.
INSTALLATION SHALL ONLY BE PERFORMED BY A PROFESSIONAL ELECTRICIAN QUALIFIED FOR UNASSISTED
OPERATIONSWITH ELECTRICAL INSTALLATIONS UP TO 1000V AFTER CAREFUL STUDY OF THE PRESENT USER'S
MANUAL.
THE RATED ELECTRICAL PARAMETERS ARE STATED ON THE RATING PLATE. ANY TAMPERING WITH THE
INTERNAL CONNECTIONS IS PROHIBITED AND WILL VOID THE WARRANTY.

www.ventilation-system.com
20
Name
Transformer parameters
Note
Power [W] Voltage [V]
Input Output
Control unit KVR-T-12 (230 V / 50 Hz) 12 230/50 Гц 12 Maximum 4 ventilators to be connected
Control unit KVR-T-12 (120 V / 60 Hz) 12 120/60 Гц 12 Maximum 2 ventilators to be connected
Control unit KVR + transformer TRF 220/12-12 12 230/50 Гц 12 Maximum 4 ventilators to be connected
Control unit KVR + transformer TRF 120/12-12 12 120/60 Гц 12 Maximum 2 ventilators to be connected
Control unit KVR + transformer TRF 220/12-40 40 230/50 Гц 12 Maximum 12 ventilators to be connected
Control unit KVR + transformer TRF 120/12-40 40 120/60 Гц 12 Maximum 6 ventilators to be connected
Name
Transformer parameters
Note
Power [W] Voltage [V]
Input Output
Control unit KVS-T-12 (230 V / 50 Hz) 12 230/50 Гц 12 Maximum 4 ventilators to be connected
Control unit KVS-T-12 (120 V / 60 Hz) 12 120/60 Гц 12 Maximum 4 ventilators to be connected
Control unit KVS + transformer TRF 220/12-12 12 230/50 Гц 12 Maximum 4 ventilators to be connected
Control unit KVS + transformer TRF 120/12-12 12 120/60 Гц 12 Maximum 4 ventilators to be connected
Control unit KVS + transformer TRF 220/12-40 40 230/50 Гц 12 Maximum 12 ventilators to be connected
Control unit KVS + transformer TRF 120/12-40 40 120/60 Гц 12 Maximum 12 ventilators to be connected
CONTROL UNIT KVRT FOR THE VENTILATORS TWINFRESH RA50 AND TWINFRESH SA150
CONTROL UNIT KVST FOR THE VENTILATORS TWINFRESH SA60
The control unit is used to set one of two operation modes of the ventilator:
1. Ventilation mode (air supply/air extract)* at the rst and second speed.
3. Reversible (regeneration) mode at the rst and second speed. The air
direction changes each 70 seconds.
*- air ow direction is determined by the JMP1 jumper position on the
ventilator circuit board. By default the jumper is set to air supply mode.
Air supply/extract mode*
Second speed
Activation
First speed
Regeneration mode
Deactivation
Selection of a required control unit modication is based on power supply voltage and transformer power, see the table below.