Venture Industries RF/EC Series User manual

OPERATION AND MONTAGE MANUAL NO RFEC/U/2017-1 (EN)
(valid since 18.08.2017)
Venture Industries Sp. z o.o. is not responsible for any damage caused by improper use of the fan and reserves the right to modify this document
without informing the user.
Venture Industries Sp. z o.o. http://www.venture.pl Tel. [phone]
Mokra 27 e-mail: [email protected] Fax [phone]
05-092 Łomianki-Kiełpin, Poland
OPERATION AND MONTAGE MANUAL
ROOF FANS
RF/EC...-... / RFV/EC...-...

Page 2 z 10
Venture Industries Sp. z o.o.
Mokra 27 Street
05-092 Łomianki-Kiełpin
Poland
OPERATION AND MONTAGE MANUAL
No RFEC/U/2017- 2 (EN)
tel. [phone], fax [phone], e-mail: [e-mail]
INTRODUCTION
This manual covers fans in standard version, listed on the title page and it is source of information necessary for safe and
proper use. Read this manual carefully before any use of the device, comply with it requirements and keep it in place with easy
access for users and service. If case of any doubts about use of the fan, please contact with manufacturer.
After receiving the device - check
• whether the device is in compliance with order,
• whether the data on the rating plate are the same as desired (voltage, frequency, etc.)
• whether fan was not damaged during transport (e.g. there are no dents/cracks, impeller rotates freely)
In case of any irregularities, contact with your dealer or Venture Industries Sp. z o.o. service.
1. GENERAL INFORMATION
1.1 Information about device
• The fan is a not completed machine within the meaning of the Machinery Directive 2006/42/WE (please refer to the manufacturer's
declaration –Appendix C). Product is in conformity with the Commission Regulation (EU) No 1253/2014 implementing ErP Directive
2009/125/EC with regard to eco-design requirements for ventilation units. Additional information can be found on the manufacturer's website
(www.ventur.eu).• Fan is designed for use by trained, qualified adult persons. The fan is not designed for household and similar use.
• The device is designed to transport clean air or air with low level of contamination. Do not transport the explosive mixtures, liquids, viscous
substances, substances with high humidity, substances that cause erosion, solid elements, and chemically reactive compounds - we
recommend the use of suitable filters. The maximum temperature of transported medium is specified on the fan nameplate, the minimum
is -20°C.
• The fan is designed for outdoor use. It must be protected from effects of lightning. The fan surroundings cannot contain explosives
atmospheres, substances causing abrasion, chemically aggressive substances and viscous substances. The maximum ambient temperature is
specified on the fan nameplate, minimum is -20°C (or lower – if confirmed by the manufacturer).
• The fan with EC type motor (electronically commutated) has built-in speed regulator (see chapter 4.2 - Guidelines for regulation) with soft
start and protections against effects of blocked impeller, overload, overheating, voltage drop or overvoltage.
• The fan has a removable cover – in order to gain access to the fan interior, move the cover after releasing the fasteners.
● The fan has following marks:
-warnings and information (optional): information about risk associated with use of the fan and about correct fan installation and operation
-fan nameplate with: logo and manufacturers name (Venture Industries Sp. z o.o.); full fan name; basic information –supply voltage and
frequency, rated current, maximum temperature of ambient and transported medium (Temp. max. or Temp. ambient max.), weight (Weight),
type of work; type of fan motor (Motor); information according to conformity with ERP Directive; article no. (Art. No.) serial no. (No.).
-direction arrows: information about correct direction of impeller rotation (rotation arrow can be placed on nameplate)
1.2 General risk and guidelines
During entire fan life cycle pay particular attention to the risk and guidelines presented below:
1.2.1 Mechanical risk and guidelines
• The fan has moving elements (e.g. impeller). Do not use the fan without installed proper protection structures (e.g. guards on inlet and
outlet) protecting from contact with moving elements. Prevent from opening the fan by unauthorized persons
• The fan has high suction power. Clothing, hair, assembly elements, items, and even body elements can be easily sucked in.
Make sure that before start and during operation of the fan, near the fan inlet there is no person and items which can be
sucked. It is forbidden to approach the fan in “loose” clothing or reaching toward inlet of working fan. Use appropriate inlet
covers and If necessary –use relevant protective clothing (e.g. headgears).
Warning: Risk of serious injury.
• The air at the outlet of the fan has high energy. Elements sucked or placed inside the fan can be thrown with a high speed. In case of damage
or improper operation, parts (with high kinetic energy) can be thrown out from fan. It is forbidden to look into the fan reaching toward inlet
and outlet of the working fan. Make sure that before start and during operation of the fan there is no person on inlet side and in stream of
transported medium. Do not use fan without proper safety constructions, inlet and outlet covers.
• During manufacturing the fan sharp edges was grinded. However the fan may have edges touching which may cause injury. We recommend
the use of relevant protective gloves.
• Conveying equipments and fan support structures must by selected proper to the fan weight and ensure that fan would not move. Do not
approach the hanging load during transport.
• The fan has a high inertness. In case of no permanent fix turning on the fan will lead to it uncontrolled movement. The unit can work only
after proper installation.
• Uncontrolled start of the fan can create hazard situation. Prevent against unexpected start of the fan – see also 1.2.6.
1.2.2 risk and guidelines related with noise
• The sound pressure level is not the same over the fan whole range. We recommend to check the sound pressure level and if
necessary use the silencer and relevant sound protection.
1.2.3 risk and guidelines related with used materials
• In case of fire or transport of improper medium – fan parts can generate fumes hazardous to health. See also 1.2.5.
1.2.4 risk and guidelines related with environment

Page 3 z 10
Venture Industries Sp. z o.o.
Mokra 27 Street
05-092 Łomianki-Kiełpin
Poland
OPERATION AND MONTAGE MANUAL
No RFEC/U/2017- 2 (EN)
tel. [phone], fax [phone], e-mail: [e-mail]
The fan can make over and under pressure. In areas where a specified air pressure and the quantity of air are required (eg. in places with
combustion) make sure that there would be no deficit/excess of air. Ensure that the installation to which the fan is connected withstand the
under/over pressure which can be made by fan (including work with forbidden parameters).
1.2.5 risk and guidelines related with temperature
The housing and fan elements are not insulated and take the temperature of the transported medium. During transport the temperature of
medium and fan components may increase. Electric motor may heat up to high temperatures (especially when overloaded/overheated –cased
by eg. blocking the impeller, too low supply voltage, too high medium temperature). The appropriate steps should be made to prevent from
fire and burns caused of high temperatures.
In case of fire –to extinguish a fire use fire extinguisher approved for electrical equipment and follow recommendation of fire department.
1.2.6 risk and guidelines related with electricity and unexpected start/ connecting power supply
Before any work on the fan (e.g.: installation, maintenance and review, dismantling) the power supply must be completely
disconnected (all poles, check there is no voltage, disconnecting switch with minimum 3mm insulation gap).
Make sure that power supply won’t by connected during the work on the unit, and that the moving parts do not move. It is
recommended to wait 3 minutes after disconnecting unit before open the fan cover.
Warning: risk of electric shock.
The appropriate steps should be made to prevent from electric shock. Protect from getting access to the electric elements by unauthorized
person.
Fan is not equipped with control system which blocks restart after a power shutdown or failure –the return of power supply cause in
immediate start. Make sure that there will not be any dangerous and forbidden situation in case of temporary power supply failure.
The built-in motor regulator protection turns off fan only during the failure. This protection after tripping (e.g. caused by motor temperature
overload) resets automatically (e.g. after cooling down motor temperature). Make sure that there won’t be any dangerous and forbidden
situation after tripping motor protections.
In case of blocking the impeller –release of impeller can provide to sudden movement. Take appropriate steps to prevent form blocking
impeller, and in such case turn off power supply and review the fan (see chapter 5).
After disconnecting power supply the fan rotating parts are still rotating for period of time under the accumulated energy. Take it into
account when using the fan.
1.2.7 risk and guidelines related with use
Improper installation and use may lead to damage of the device and to the dangerous situation. The unit can by installed, maintained,
dismantled and used only by qualified and authorized personnel, in accordance to safety rules and current regulations in the country of use
(including proper electrical authorization). Personnel need to be familiar with reactions of the fan.
If it is necessary to remove parts of the unit (e.g. during montage or maintenance), users must be warned about the potential
risk, and these parts of unit must be closed/mount after the completion of the work.
It is forbidden to use the unit if it is incomplete / disassemble.
Warning: Risk of serious injury.
• The device must not be exposed to radiation (such as microwave, UV, laser, x-ray).
• Any modifications of the unit are forbidden. Complicated maintenance work (such as dismantling the motor or impeller) need to be made by
Venture Industries Sp. z o.o. service or with it permission. Improper assembly may lead to reduce the fan parameters, damage the unit and
lead to the dangerous situation.
1.2.8 risk and guidelines related with explosive atmospheres
Contact of the fan with explosive atmospheres could cause the ignition. It is forbidden to storage or use the fan with explosive atmospheres
inside or outside the unit.
2. TRANSPORT AND STORAGE
During transport and storage follow the guidelines contained in 1 chapter and transport and storage guidelines.
2.1 transport and storage guidelines
The fan should be transported and stored in original packaging, without excessive shocks. The device must be protected from weather
conditions, transported and stored in dry, well ventilated, and free from substances harmful to the device areas. The fan cannot be transported
and stored in areas with fertilizers, chlorinated lime, acids and other aggressive chemicals. Fan should be protected against foreign body
entrance.
During transport and storage protect the fan against damage (including crush).
The unit should be lifted by the base. Do not lift the unit by wires, terminal box, grid, impeller, cover.
It is recommended that storage time not exceed one year. After long storage, check the fan. (chapter 5).
3. MONTAGE AND INSTALLATION
During installation follow the guidelines contained in 1 section of this instruction and and installation guidelines.
3.1 installation guidelines
The fan is a machine not ready for use (within the meaning of the Machinery Directive 2006/42/WE - before use ensure conformity with
requirements of Machinery Directive 2006/42/EC and current editions (with changes) of: EN ISO 12100, EN ISO 13857, EN 349+A1, EN ISO
13850, EN 60204-1.
Before installation remove temporary items that protect fan during transport and storage (e.g. box, foil, caps –do not remove any guards) –
Starting the fan with those items could lead to damage of the fan. Make sure that the fan is not damaged.

Page 4 z 10
Venture Industries Sp. z o.o.
Mokra 27 Street
05-092 Łomianki-Kiełpin
Poland
OPERATION AND MONTAGE MANUAL
No RFEC/U/2017- 2 (EN)
tel. [phone], fax [phone], e-mail: [e-mail]
The device must be mounted in the horizontal orientation with cover on top, in accordance with drawing below (the arrows show the air flow
direction). The fan needs to be mounted to external constructions (we recommend use of dedicated roof stand) with use all montage holes
placed on the fan base. Due to the use of the fan outdoor –prevent form leakage of water between the fan base and montage construction by
proper sealing.
The fan support construction must be able to support the fan working with the full power (start-up, breakdown, improper use should by also
consider). For installation use connecting elements secured against self-loosening.
Note: Fan housing is made of aluzinc steal / zinc steal (depending of fan model).
Install proper protective structures, grids (inlet, outlet, moving parts), if not mounted by manufacturer. Open inlet of the fan need to be
protected proper by proper grid.
Note: Although normally used shields the device should be installed in such a way that prevent from getting access to the device (rotor) from
the outlet.
It is recommended to use accessories to minimize the vibration transmitted from/to the fan.
It is recommend to provide the distance of 3 inlet dimensions of clearance between inlet and any obstructions (such as filters, bends, wall)
and distance guaranteeing free air movement.
After fan mechanical installation make all electrical connections and check the impeller direction of rotation in accordance with points 3.2
and 3.3.
Ensure that there are no foreign bodies (eg. mounting elements, tools) inside and near of the unit, that impeller is not blocked, the fan is
properly secured after installation (the cover is closed and secured, the terminal box/service switch is closed, the fastening elements are
properly tightened).
3.2 electrical connection guidelines
The fan and power supply network must be secured in accordance with local law requirements.
Use protection against short circuits, overloads and for fans with three phase power supply - voltage failure/unbalance.
Use appropriate protection against electric shock - it is required to connect fan grounding terminal placed inside connection box to proper
grounding system.
The electrical connection need to be made in accordance with the data on the fan and motor nameplates, motor manual (if included), proper
wiring diagram and fan marking.
Depending on the chosen speed regulation method it is needed to connect adequate devices or signal wires to speed regulation system
terminals (see appendix C).
Voltage and frequency of supply network should be as indicated on the fan nameplate. The fan has built-in speed regulator.
It is forbidden to use voltage or frequency regulators to supply unit. Voltage or frequency regulation is ineffective and could
lead to the fan damage.
Use electrical wires with proper insulation and size. Wires should be placed in way that in any situation will not touch the moving elements,
and that the water (e.g. from condensation) not flow inside the junction box. Wires should be connected to the terminal box, through properly
tightened cable glands and wire fasteners.
3.3 rotor rotation direction
The fan has built-in speed regulator which do not allow to change the direction of rotor rotation, although if the impeller would rotate in
incorrect direction contact with manufacturer.
4. USE
During fan use follow the guidelines contained in 1 section of this instruction and use guidelines.
Before first start of the fan follow guidelines from chapter 5.
4.1 use guidelines
Make sure that turning on of the fan does not make any risk for personnel and property.
Fan cannot work with voltage, frequency, current higher than shown on the fan nameplate.
The fan is designed for continuous operations (S1) –too high frequency of turning may lead to the motor regulator overheat and damage
(see also chapter 4.2 Guidelines for regulation).
In case of activation of any electrical protection, detection of damage, working with current greater than specified on the fan nameplate –
unit must by immediately turn out off use.
During fan regulation –follow regulation guidelines in chapter 4.2.

Page 5 z 10
Venture Industries Sp. z o.o.
Mokra 27 Street
05-092 Łomianki-Kiełpin
Poland
OPERATION AND MONTAGE MANUAL
No RFEC/U/2017- 2 (EN)
tel. [phone], fax [phone], e-mail: [e-mail]
4.2 Guidelines for regulation
The fan has built-in speed regulator of EC type motor (see connection diagram - appendix C) allowing regulating speed in following methods:
1) maximal speed operation
2) rotor speed proportional to input signal on the input, set by potentiometer 0-10 kΩ and internal source of 10V DC signal.
3) rotor speed proportional to input signal on the input, set by external source of analogue signal 0-10 V DC or signal 1-10 kHz PWM.
The fan start is done over 0,8 V (8% PWM) - below this value the fan stops. For models with DIGITAL INPUT it is also needed
connection signal from DC OUT output to this input to enable operating (start permission).
For start and stop of the fan it is recommended to use input signals (DIGITAL INPUT or INPUT 0-10V). Control by cutting-off
the power supply e.g. by contactor, is not recommended and in wrong conditions (responsive on/off) could lead to the fan
damage.
Built-in controller change the fan speed proportional to the level of input analogue signal.
The minimal speed is set by 1 V / 10% PWM signal and maximal speed by 10 V / 100% PWM signal.
Never overload fan voltage outputs, the standard limit of load current on signal output is 2,5 mA. Limit values for no standard signal outputs
are shown on connection diagrams.
• The parameters of the device (ambient and operation temperature, flow rate min and max etc.) refer to the rated speed. Too slow rotation
speed can lead to the deterioration of motor cooling and cause to overheating / damage.
5. MAINTENANCE, REVIEW
During maintenance and review follow the guidelines contained in 1 chapter of this instruction and maintenance guidelines.
5.1 maintenance guidelines
Fan must be subject of regular review and maintenance (point 5.2). The set between routine checks and maintenance should be determined
by user, based on the observation of unit and specific conditions and actions. If irregularities are found, the device must be taken out of
service and repaired.
To clean fan use slightly damp delicate material. It is prohibited to use detergents, liquids under pressure and tools that may scratch the unit
surface. After fan cleaning (after end of maintenance) turn on the fan for 30 minutes (with full speed).
In case of long fan downtimes it should be run at least once per month for 2 hours (with full speed).
Prevent the accumulation of dust/dirt on and inside the fan. Dirt accumulated on: grids –may reduce the fan parameters; impeller –may
lose it balance; housing and motor –can reduce the cooling; hot surfaces –in extreme situations may ignite. If the device is secured by filter -
filter should by regularly inspected and replaced if it pollution is too high. The dirt accumulated on the filter reduces the fan parameters.
Ensure that there are no foreign bodies near and inside the fan, the impeller is not blocked, the unit is clean, dry and secured after
maintenance and review.
Fan motor is equipped with bearing with life expectancy 40 000 hours (ambient temperature 40˚C). Bearings do not need refill lubricate.
5.2 Unit maintenance and review
During review and before first use of the unit or after long time period of storage attention to the following should be paid:
accumulation of the dirt on the unit and filter (if used), state of grid / covers,
is the device stable, not damaged, the structure is complete, moving elements can move freely,
if there are any foreign bodies or loose elements inside the fan,
if there is loose bearing and rotating the shaft cause in its heavy/noisy work,
are connecting elements tightened, is fan surface without corrosion, are electrical wires not damaged,
is the safety equipment working and property set, is shock protection effective,
if there are leaks from the motor, overheating and vibrations.
During operations, especially after first start pay attention to:
correct operation,
there are no unusual noises and vibrations, leaks from the motor, overheating or vibrations,
the grids are in proper condition,
the fan current is not higher than show on nameplate. Exceed of current placed on the name plate could by a sign of unit damage.

Page 6 z 10
Venture Industries Sp. z o.o.
Mokra 27 Street
05-092 Łomianki-Kiełpin
Poland
OPERATION AND MONTAGE MANUAL
No RFEC/U/2017- 2 (EN)
tel. [phone], fax [phone], e-mail: [e-mail]
6. REPAIR, WARRANTY
Use only original spare parts and original accessories. Fan repairs need to be made by manufacturer or after manufacturer permission.
Warranty conditions are placed in the fan warranty card.
7. DISMANTLING AND RECYCLING
Disconnect unit from its power supply, and dismount according to the guidelines from section 1 of this instruction. Therefore, please deposit all
left-over material and packaging in their corresponding recycling containers and hand in the replaced machines to the nearest handler of this
type of waste product.

Page 7 z 10
Venture Industries Sp. z o.o.
Mokra 27 Street
05-092 Łomianki-Kiełpin
Poland
OPERATION AND MONTAGE MANUAL
No RFEC/U/2017- 2 (EN)
tel. [phone], fax [phone], e-mail: [e-mail]
APPENDIX A - (THE DEVICE RECEIPT FORM)
Before launch
Check
confirmation
Type and model of fan are in accordance with the order.
The fan is undamaged.
There is no foreign body inside fan and the fan is clean.
The fan is reliably and solidly fixed in workplace.
The fan is properly levelled
Wires are properly tightened.
Ambient temperature and transported medium temperature are compatible with fan nameplate
Proper electrical protection is applied
Grounding of fan is applied.
Mains supply is compatible with fan power supply.
Power supply disconnecting switch (with 3mm visible gap) is applied.
Personnel using the fan read and understood the operation and montage manual.
Proper inlet and outlet covers (grids) have been applied
After fan launch (continuous work period minimum 30 minutes)
Readings and set of vibration measurement device has been written (they are available in future)
Readings and set of current measurement device has been written (they are available in future)
Value of current for each of phase does not exceed nominal one
The vibration value is not higher than permitted.

Page 8 z 10
Venture Industries Sp. z o.o.
Mokra 27 Street
05-092 Łomianki-Kiełpin
Poland
OPERATION AND MONTAGE MANUAL
No RFEC/U/2017- 2 (EN)
tel. [phone], fax [phone], e-mail: [e-mail]
APPENDIX B - (EXAMPLES OF DEVICE FAULTY WORKING)
SYMPTOMS
POSSIBLE REASON
Excessive vibration or
noise
Damaged impeller
Dirt accumulated on impeller caused loss of balance;
Impeller loss of balance;
Parts rubbing;
Damage or wear of bearings;
Failed fan start-up/
stop during
operation.
Rubbing between fan impeller and housing or foreign body (e.g. tool left after installation);
Overload of motor or electronic controller;
Damage or wear of bearings;
Power failure or phase failure;
Too high or too low supply voltage;
Electronic controller lock up (power restart needed);
No power restart done after activation of motor protective modules.
Protective modules or
devices activation
during fan
work and overheating
Excessive start-up time;
Motor overload;
Shortcut in power adapter circuits of EC motor;
Too often start-ups;
Improper set of protection circuit breaker and / or incorrect set of protective relays;

Page 9 z 10
Venture Industries Sp. z o.o.
Mokra 27 Street
05-092 Łomianki-Kiełpin
Poland
OPERATION AND MONTAGE MANUAL
No RFEC/U/2017- 2 (EN)
tel. [phone], fax [phone], e-mail: [e-mail]
APPENDIX C - CONNECTION DIAGRAMS
Single phase fan : RFEC - 125L, 125H, 125E, 160H, 200, 250L
Single phase fan : RFEC –250H, 315,

Page 10 z 10
Venture Industries Sp. z o.o.
Mokra 27 Street
05-092 Łomianki-Kiełpin
Poland
OPERATION AND MONTAGE MANUAL
No RFEC/U/2017- 2 (EN)
tel. [phone], fax [phone], e-mail: [e-mail]
Three phase fan: RFEC –315T, 355T, 400T, 450T, 500T
Note: Unit generates leakage current <= 3,5 mA.

Page 11 z 10
Venture Industries Sp. z o.o.
Mokra 27 Street
05-092 Łomianki-Kiełpin
Poland
OPERATION AND MONTAGE MANUAL
No RFEC/U/2017- 2 (EN)
tel. [phone], fax [phone], e-mail: [e-mail]
APPENDIX D - DECLARATION OF MANUFACTURER

Page 12 z 10
Venture Industries Sp. z o.o.
Mokra 27 Street
05-092 Łomianki-Kiełpin
Poland
OPERATION AND MONTAGE MANUAL
No RFEC/U/2017- 2 (EN)
tel. [phone], fax [phone], e-mail: [e-mail]

Page 13 z 10
Venture Industries Sp. z o.o.
Mokra 27 Street
05-092 Łomianki-Kiełpin
Poland
OPERATION AND MONTAGE MANUAL
No RFEC/U/2017- 2 (EN)
tel. [phone], fax [phone], e-mail: [e-mail]

Page 14 z 10
Venture Industries Sp. z o.o.
Mokra 27 Street
05-092 Łomianki-Kiełpin
Poland
OPERATION AND MONTAGE MANUAL
No RFEC/U/2017- 2 (EN)
tel. [phone], fax [phone], e-mail: [e-mail]