Verbatim 70190 User manual

Installation Guide
WARNING – RISK OF SERIOUS INJURY AND PROPERTY DAMAGE
Carefully read all instructions and product labels prior to installation.
To reduce risk of death, personal injury, electric shock, cuts/abrasions, falling parts or property damage from fire, carefully read all
warnings, instructions and product labels.
Wear gloves and safety glasses at all times when removing light fixture from carton, installing, servicing or performing maintenance.
Ensure that your installation matches all elements shown in the descriptions and drawings of the installation instructions before you
begin.
Save these instructions for future reference.
• PRIOR TO INSTALLATION, MAINTENANCE, INSPECTION OR REMOVAL, TURN OFF ELECTRICAL POWER AT FUSE OR
CIRCUIT BREAKER BOX.
• CAUTION: RISK OF FIRE OR ELECTRIC SHOCK. DO NOT use input power other than the voltage specified in the product
specifications.
• The installation, service and maintenance of this light fixture must be performed by a licensed electrician. If you are not
qualified, contact a licensed electrician.
• Product installation must comply with the National Electrical Code and all local electrical and building codes and regulations.
• All wiring connections should be capped with UL approved wire connectors.
• DO NOT use outdoors.
• DO NOT install if product is damaged.
• DO NOT use this equipment other than for its intended use.
• DO NOT allow the wiring to contact sharp edges, such as sheet metal edges.
• Suitable for use in damp locations.
• Suitable for use in -30 to 50 ºC ambient temperatures.
• May not be compatible with all dimmers. For up-to-date compatibility, visit www.verbatimlighting.com/dimmer_support
• Keep combustible and other materials that can burn away from light fixture and lamp/lens.
• Avoid looking directly into light while on.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause
harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired
operation.
Safety Information
Product Specifications
Part
Number
Model
Number
Input
Voltage
(VAC)
Input
Wattage
(W)
Input
Current
(mA)
Input
Frequency
(Hz)
Lumens CCT
(K)
Dimensions
L x W x H
Weight
70190 HB-110W-C40-P
120-277
110 1000
50/60
14,300
4000
23.8 x 12.6 x 2.68 inches
320 x 605 x 68 mm
8.77 lbs.
3980 grams
70191 HB-165W-C40-P 165 1600 21,450 23.8 x 17.3 x 2.68 inches
440 x 605 x 68 mm
11.86 lbs.
5380 grams
70192 HB-225W-C40-P 225 2000 29,250 45.9 x 12.6 x 2.68 inches
320 x 1166 x 68 mm
15.9 lbs.
7210 grams
70193 HB-110W-C50-P 110 1000 14,300
5000
23.8 x 12.6 x 2.68 inches
320 x 605 x 68 mm
8.77 lbs.
3980 grams
70194 HB-165W-C50-P 165 1600 21,450 23.8 x 17.3 x 2.68 inches
440 x 605 x 68 mm
11.86 lbs.
5380 grams
70195 HB-225W-C50-P 225 2000 29,250 45.9 x 12.6 x 2.68 inches
320 x 1166 x 68 mm
15.9 lbs.
7210 grams

Installation Guide
Installation Instructions
Included chain kit:
• V hooks (2)
• 1.05m chain (2)
1. Thread the end of a chain over each V hook. Secure each chain to a load bearing structure that is rated for the weight of the
fixture. See Figure 1 (chain mounting case).
2. Insert V hooks onto two opposite sides of the fixture. Make sure the hooks are fully engaged into the side holes as shown. See
Figure 2.
3. Remove the cover plate in the center of the driver housing.
4. Connect the main power supply and 0-10V dimming control wires according to the wiring diagram in Figure 3. Replace the
cover plate.
5. Double check the security of all mounting hardware.
Warranty & Support
Verbatim 5-year warranty www.verbatimlighting.com/warranty.
For support, visit www.verbatimlighting.com/support
May not be compatible with all dimmers.
For up-to-date compatibility please visit www.verbatimlighting.com/dimmer_support.
Wiring Diagrams
LED Driver
Black (Line)
White (Neutral)
Green (Ground)
Power
120-277V
Wires to
LED Load
0-10V
Dimmer
Purple
(DIM+)
Gray
(DIM-)
Red
(+)
Blue
(-)
Black (Line)
White (Neutral)
Green (Grd)
120 - 277v
General Wiring Diagram
Dimming wire
to 0-10v.
Lead wire to
LED load.
LED Driver
Purple (Dim+)
Grey (Dim-)
Blue (-)
Red (+)
Figure 1
Figure 2
Figure 3