Vermeiren Luna 2 User manual

VERMEIREN
INSTALLATION MANUAL
Luna 2, Luna Basic 2,
Luna UL 2

Luna 2, Luna Basic 2, Luna UL 2
2021-03
Content
Installation manual
1
EN
NL
Content
Content ................................................................................................................................... 1
Preface .................................................................................................................................... 2
1 This product............................................................................................................... 3
2 Scope of delivery ....................................................................................................... 5
3 Assembly ................................................................................................................... 6
3.1 Tools ............................................................................................................................ 6
3.2 Assembling the bed ..................................................................................................... 7
3.3 Strain relief and power cable ..................................................................................... 10
3.4 Cable placement ....................................................................................................... 11
3.5 Transport ................................................................................................................... 12
3.6 Lifting pole (optional) ................................................................................................. 14
3.7 Emergency lowering of the headrest ......................................................................... 14

Luna 2, Luna Basic 2, Luna UL 2
2021-03
Preface
Installation manual
2
EN
NL
Preface
To support you on the installation and repairs of this nursing bed, we provide you with this
installation manual. Please read it carefully. If you still have questions after reading this manual,
do not hesitate to contact Vermeiren.
The information in this manual applies to the following bed(s):
 Luna 2
 Luna Basic 2
 Luna UL 2
Important note
Pictures of the product are used to clarify the instructions. Details of the shown product may
deviate from your product.
Available information
On our website http://www.vermeiren.com/ you will always find the most recent version of the
information in this manual. Please consult this website regularly for possible updates.
Visually impaired people can download the electronic version of this manual and have it read out
by means of a text-to-speech software application.
User manual
For user and specialist dealer
Installation manual
For specialist dealer
Service manual for beds
For specialist dealer
Drawings of (spare) parts
For specialist dealer
EC declaration of conformity

Luna 2, Luna Basic 2, Luna UL 2
2021-03
This product
Installation manual
3
EN
NL
1 This product
1
2
3
4
5
6
7
8
9
10
Luna 2
1
2
3
4
5
6
7
8
9
10
Luna Basic 2
1. Head panel
2. Lifting pole
3. Mattress retainer
4. Side rail
5. Foot panel
6. Castor
7. Foot end
8. Head end
9. Handset
10. Identification plate

Luna 2, Luna Basic 2, Luna UL 2
2021-03
This product
Installation manual
4
EN
NL
Luna UL 2
1
2
3
4
5
6
7
8
9
10
1. Head panel
2. Lifting pole
3. Mattress retainer
4. Side rail
5. Foot panel
6. Castor
7. Foot end
8. Head end
9. Handset
10. Identification plate

Luna 2, Luna Basic 2, Luna UL 2
2021-03
Scope of delivery
Installation manual
5
EN
NL
2 Scope of delivery
The following components are part of the delivery:
 Head and feet end incl. motors + wooden panels
 Slatted frame, foot-end incl. motor
 Slatted frame, head-end incl. transformer and motor
 Side railings (2 x 2 wooden slats)
 Lifting pole + triangular grip
 Handset
 Instruction manual
 Optional accessories
Before use, check if everything is included and that no products are damaged.

Luna 2, Luna Basic 2, Luna UL 2
2021-03
Assembly
Installation manual
6
EN
NL
3 Assembly
Risk of injury
 Only use the settings described in this manual.
 Prevent trapping your hands when assembling, disassembling or using the bed.
 Make sure that no body parts or objects are present when adjusting hinges, joints or other
clamps.
 Only use genuine spare or replacement parts approved by Vermeiren.
Important remarks
 Read the user manual of this bed.
 Be aware of the technical details and limits of intended use; see the user manual.

For more information, contact
Vermeiren
.
3.1 Tools
No tools are needed to set up the bed.
CAUTION

Luna 2, Luna Basic 2, Luna UL 2
2021-03
Assembly
Installation manual
7
EN
NL
3.2 Assembling the bed
Risk of injuries
 Keep your fingers and the electric cables away from moving parts, and make sure that they do
not become trapped between components during assembly.
 No third persons or any objects may come in the assembly area.
Follow the order of assembly as explained below.
3.2.1 Head panel / feet panel
1. Mount the attachment of the slatted frame (3) on the attachment of the head panel (4).
2. Secure the slatted frame (1) with the locking clamps (5).
3. Repeat for the feet panel. Check that the slatted frames are mounted very well.
The slatted frame can be mounted in 2 different positions (Ⓑ, Ⓒ): step 64 mm (not for Luna UL
2).
3.2.2 Slatted Frame
CAUTION
1 = Slatted frames
2 = Fixing screws
1 = Slatted frame
2 = Head and foot panels
3 = Attachment slatted frame
4 = Attachment panels
5 = Locking clamp

Luna 2, Luna Basic 2, Luna UL 2
2021-03
Assembly
Installation manual
8
EN
NL
1. Loosen the fixing screws (2), if necessary.
2. Erect both slatted frames (1) and insert them into each other.
3. Retighten the fixing screws (2) of the slatted frame connection.
3.2.3 Wooden side rails
Adjust the bed to medium height. If the bed is adjusted too low, it is not possible to mount the side
rails; if it is adjusted too high, you have to pull the side rails too far upwards.
For Luna 2, Luna Basic 2
Risk of injuries
 The side rails can be mounted in a high or low position.
Place the side rails in the lowest position
when the slatted frame is mounted in the lowest height.
WARNING
6
5
1 = Highest position
2 = Lowest position
1 = Bolt rails
2 = Wood slats (2 pieces each side)
3 = Sliding rail
4 = Locknut
5 = Stop
6 = Screw

Luna 2, Luna Basic 2, Luna UL 2
2021-03
Assembly
Installation manual
9
EN
NL
1. Insert the stop (5) and screw (6) in the top or lower hole according to the desired height of the
side rails.
2. Loosen the locknuts (4), if necessary.
3. Insert the bolt rails (1) on the right and left in the upper wood slat (2). Insert the bolt rails (1)
right and left in the lower wood slat (2).
4. Slide the entire bolt rails (1) + wooden slats (2) in the relevant sliding rail (3) from the head
and foot panel. Grasp the upper wooden slat and pull upwards until the wooden side rails lock
in position.
5. Insert the locknuts (4) and tighten them manually.
6. Repeat these steps for the other side.
For Luna UL 2
1. Loosen the locknuts (4), if necessary.
2. Insert the bolt rails (1) on the right and left in the upper wood slat (2). Insert the bolt rails (1)
right and left in the lower wood slat (2).
3. Slide the entire bolt rails (1) + wooden slats (2) in the relevant sliding rail (3) from the head
and foot panel. Grasp the upper wooden slat upwards until the wooden side rail locks in
position.
4. Insert the locknuts (4) and tighten them manually.
5. Repeat these steps for the other side.
1 = Bolt rails
2 = Wood slats (2 pieces each side)
3 = Sliding rail
4 = Locknut

Luna 2, Luna Basic 2, Luna UL 2
2021-03
Assembly
Installation manual
10
EN
NL
1 2 3 4 5
6
3.2.4 Split side rails
Mind the difference between head-end and foot-
end rails
(head
-
end rails are shorter than foot
-
end rails).
1. Take one of the split side rails.
2. Place the split side rail attachments (1) over the mattress
frame support (2).
3. Firmly tighten the two screws (3) on the bottom of each
attachment.
4. Repeat for all other split side rails.
5. Make sure that all side rails are firmly attached into place.
3.2.5 Transformer connections
Risk of injury
 Do not place any objects on the connection and the cable, and protect them against mechanical
loads.
1. Connection requires a 220V/230V, 50Hz power socket conform to VDE specifications.
2. The diagram for the transformer connections is given in the figure below:
The motor connection plugs are labelled with the same number as the connections on the
transformer.
Take hold of the plug only to remove it from the power socket.
The power connection must not have any loops or kinks and should not pass around sharp edges.
Protect the power connection and the cable leading to the handset from being crushed.
3.3 Strain relief and power cable
Risk of damage
 Do not remove the relief unit.
 Nothing must be fitted to or hung on the relief unit.
 The power cable must be carefully positioned without kinks, without pulling, and without
touching the floor.
Below the cross bar of the head slatted frame there is a socket for attaching the relief unit.
1. Insert the relief unit of the power cable (4) into the suspension (3).
2. Pull the desired length of the power cable (1) in such a way that the power cable (2) can
be laid under the slatted frame without sagging. Be careful to avoid that the cable (2) come
under the traction in any adjustment position.
CAUTION
CAUTION
1 = Connection of panels motor
2 = Connection of knee-bending angle motor
3 = Connection of head-end motor
4 = Connection of foot-end motor
5 = Handset
6 = Transformer / control box
3
2
1

Luna 2, Luna Basic 2, Luna UL 2
2021-03
Assembly
Installation manual
11
EN
NL
3. Fasten the power cable by properly tightening the relief unit of the power cable (4).
4. Fasten the position of the relief unit by properly tightening the fixing screws (5).
3.4 Cable placement
1. Mattress slatted frame head end
2. Mattress slatted frame feet end
3. Sockets lifting pole
4. Strain relief
5. Power supply
6. Control box
7. Head end motor
8. Knee-bend motor
9. Head panel motor
10. Feet panel motor
11. Handset
All wires within the bed frame should
be placed in such a way that contact
with the floor, deformity and crushing
are avoided. Insert the power cables
for the motors in the opening on the
motor mounts.
1 = Power cable
(power connection)
2 = Power cable
(Transformer
connection)
3 = Holder
Strain relief
4 = Strain relief
Power cables
5 = Screw joint
Strain relief
2
1
4
3
5
1 = Power cable
(power connection)
2 = Power cable
(transformer connection)
3 = Holder Strain relief
4 = Strain relief Power
cables
5 = Screw joint Strain relief
4 3 2 1
10
4
3
5
6
3
1
7
9
2
11
8

Luna 2, Luna Basic 2, Luna UL 2
2021-03
Assembly
Installation manual
12
EN
NL
3.5 Transport
3.5.1 Luna 2, Luna Basic 2
1. Grasp the panels (1).
2. Mount the attachment of the transport set
(2) in the attachment of the panels (3) and
lock with the locking clamps (4). Mount the
transport set in the lowest position of the
panels.
3. Lock the brakes of the panels (5).
4. Grasp the feet end (6) and hold this with the motor located
to the bottom side.
5. Slide the tube of the feet end (6) in the tube of the
transportset (7). Secure the feet end (6) with the starknobs
(8).
6. Grasp the head end (9) and hold this with the motor located
to the upper side.
7. Slide the tube of the head end (9) in the tube of the
transportset (10). Secure the head end with the starknobs
(11).
Risk of injuries or damage
Attach all bed
parts and transport trolley
firmly to the vehicle, to prevent them from moving during
transport.
CAUTION
6
7
8
9
10
11

Luna 2, Luna Basic 2, Luna UL 2
2021-03
Assembly
Installation manual
13
EN
NL
3.5.2 Vertical transport set Luna 2, Luna Basic 2, Luna UL 2
1. Grasp the head end and hold it with the motor
to the inside of the transport set.
2. Slide the bedframe tube over de short tube (1)
on the transport set. Let the other end rest on
the long transport set tube (2).
3. Secure the head end with the star knob (3).
4. Repeat the steps above for the foot end.
5. Grasp the head and foot panel.
6. Mount the panel attachments (4) to the hooks (5) of
the transport set. Lock with the locking clamps.
7. Repeat for the other panel.
1
3
2
4
5

Luna 2, Luna Basic 2, Luna UL 2
2021-03
Assembly
Installation manual
14
EN
NL
3.6 Lifting pole (optional)
The lifting pole can be mounted on either side of the head end.
1. Insert the pole (1) as far as it will go into the relevant socket (2).
2. Let the groove on the lifting pole (3) slide over the tube in the socket.
3. Pull the strap loop over the end of the upper frame (4) until the desired position.
4. Pull the strap (5) through the triangle (6). Fix its length and secure the strap.
3.7 Emergency lowering of the headrest
Risk of injury
 Make sure that there are no objects or body parts between the headrest and the frame.
 Emergency lowering is only permitted if at least two persons are available.
The headrest can be lowered manually (emergency lowering in the case of motor failure):
1. Firmly grasp the headrest to prevent it from falling.
2. A second person can release the suspension pin by folding the securing batch and pulling
the pin from the motor suspension.
3. Lower the headrest gently.
1 = Lifting pole
2 = Socket
3 = Groove
4 = Upper frame lifting pole
5 = Strap
6 = Triangle
4
5
6
3
4
1
2
1 = Suspension pin
2 = Motor attachment
3 = Headrest frames
4 = Headrest motor
CAUTION

© Vermeiren Group 2021
Vermeiren GROUP
Vermeirenplein 1 / 15
2920 Kalmthout
BE
website: www.vermeiren.com
Instructions for specialist dealer
This instruction manual is part and parcel of the product and must accompany
every product sold.
All rights reserved, including translation.
No part of this manual may be reproduced in any form what so ever (print,
photocopy, microfilm or any other process) without written permission of the
publisher, or processed, duplicated or distributed by using electronic systems.
R.E.: Vermeiren GROUP, Vermeirenplein 1/15 - 2920 Kalmthout –Belgium
Installation manual - Luna 2, Luna Basic 2, Luna UL 2_EN_A5_2021-03_A
Basic UDI: 5415174 181210Luna 2 5V
5415174 181210LunaBasic2 ZG
5415174 181210Luna UL 2 HK
Version: A, 2021-03