Vermeiren Eclips X4 User manual

VERMEIREN
Eclip X4, Eclip X4 30°
I N S T R U C T I O N M A N U A L
MODE D’EMPLOI
GEBRUIKSAANWIJZING
GEBRAUCHSANWEISUNG
I S T R U Z I O N I P E R L ' U S O
INSTRUKCJA OBSŁUGI

Instructions to the specialist dealer
This instruction manual is part and parcel of the product and must accompany every product sold.
Version: B, January 2012
All rights reserved, including translation.
No part of this manual may be reproduced in any form what so ever (print, photocopy, microfilm or any other process) without
written permission of the publisher, or processed, duplicated or distributed by using electronic systems.
© N.V. Vermeiren N.V. 2012
Instructions pour les distributeurs
Ce manuel d'instructions fait partie du produit et doit accompagner chaque produit vendu.
Version : B, Janvier 2012
Tous droits réservés, y compris la traduction.
Aucune partie de ce manuel ne peut être reproduite, sous quelque forme que ce soit (imprimée, photocopie, microfilm ou tout autre
procédé) sans l'autorisation écrite du publicateur, ni traitée, dupliquée ou distribuée à l'aide de systèmes électroniques.
© N.V. Vermeiren N.V. 2012
Instructies voor de vakhandelaar
Deze handleiding is deel van het product en dient bij iedere product te worden geleverd.
Versie: B, januari 2012
Alle rechten, inclusief vertaling, voorbehouden.
Niets uit deze handleiding mag geheel of gedeeltelijk in enige vorm (druk, fotokopie, microfilm of ieder ander procedé) zonder de
schriftelijke toelating van de uitgever worden gereproduceerd of met behulp van elektronische systemen worden verwerkt,
gekopieerd of verspreid.
© N.V. Vermeiren N.V. 2012
Hinweise für den Fachhändler
Diese Gebrauchsanweisung ist Bestandteil des Produkts und ist bei jeder Produkts auszuhändigen.
Version: B, Januar 2012
Alle Rechte, auch an der Übersetzung, vorbehalten.
Kein Teil der Gebrauchsanweisung darf in irgendeiner Form (Druck, Fotokopie, Mikrofilm oder einem anderen Verfahren) ohne
schriftliche Genehmigung des Herausgebers reproduziert oder unter Verwendung elektronischer Systeme verarbeitet, vervielfältigt
oder verbreitet werden.
© N.V. Vermeiren N.V. 2012
Istruzioni per il rivenditore
Il presente Manuale di istruzioni è parte integrante del prodotto e deve essere fornito assieme alla prodotto.
Versione: B, Gennaio 2012
Tutti i diritti riservati (anche sulla traduzione).
Il presente manuale non può essere riprodotto, neppure parzialmente, con alcun mezzo (stampa, fotocopia, microfilm o altro
procedimento) senza l’autorizzazione scritta della casa produttrice, né elaborato, duplicato o distribuito con l’ausilio di sistemi
elettronici.
© N.V. Vermeiren N.V. 2012
Instrukcje dla wyspecjalizowanego sprzedawcy
Niniejsza instrukcja obsługi jest nieodłącznączęściąproduktu i musi byćdołączona do każdego sprzedawanego produktu.
Wersja: B, Stycznia 2012
Wszelkie prawa zastrzeżone, łącznie z tłumaczeniem.
Żadna część niniejszej instrukcji nie może byćpowielana w jakiejkolwiek formie (drukowanej, fotokopii, mikrofilmu ani innej) bez
pisemnej zgody wydawcy, nie może byćrównieżprzetwarzana, kopiowana ani rozprowadzana za pomocąsystemów
elektronicznych.
© N.V. Vermeiren N.V. 2012

Eclips X4, Eclips X4 30°
2012-01
Page 1
Contents
Preface ......................................................................................................................................2
1 Productdescription......................................................................................................3
1.1 Intended Use................................................................................................................3
1.2 Technical specifications ..............................................................................................4
1.3 Drawing.......................................................................................................................6
1.4 Accessories..................................................................................................................6
1.5 Location identification plate........................................................................................6
1.6 Explanation of symbols...............................................................................................7
1.7 Safety rules..................................................................................................................7
2 Use................................................................................................................................8
2.1 Carrying the wheelchair ..............................................................................................8
2.2 Mounting the rear wheels............................................................................................8
2.3 Unfolding the wheelchair............................................................................................8
2.4 Mounting or removing of the footrests .......................................................................8
2.5 Operating the brakes....................................................................................................9
2.6 Mounting or removing of arm supports ......................................................................9
2.7 Transfer in and out the wheelchair............................................................................10
2.8 Correct position in the wheelchair ............................................................................10
2.9 Riding the wheelchair................................................................................................11
2.10 Moving on slopes......................................................................................................11
2.11 Negotiating steps or curbs.........................................................................................11
2.12 Fold up the wheelchair..............................................................................................13
2.13 Taking off the wheels ................................................................................................13
2.14 Pushbar......................................................................................................................13
2.15 Back adjusting (Eclips X4 30°).................................................................................14
2.16 Transport in the car....................................................................................................14
2.17 Use of the wheelchair as seat in a motor vehicle (Eclips X4)...................................14
3 Installation and adjustment.....................................................................................16
3.1 Tools..........................................................................................................................17
3.2 Manner of delivery....................................................................................................17
3.3 Adjusting the seat height and seat angle ...................................................................17
3.4 Flexible seat...............................................................................................................19
3.5 Adjusting seat depth..................................................................................................20
3.6 Flexible back.............................................................................................................20
3.7 Adjust the brakes.......................................................................................................20
3.8 Adjusting of the footrests..........................................................................................21
3.9 Adjusting of the pushing handles..............................................................................22
3.10 Adjusting of the tip cap.............................................................................................23
3.11 Adjusting the stability and the maneuverability........................................................23
4 Maintenance..............................................................................................................24
4.1 Regular Maintenance.................................................................................................24
4.2 Shipping and storage.................................................................................................25
4.3 Care ...........................................................................................................................25
4.4 Inspection..................................................................................................................25
4.5 Disinfection...............................................................................................................26
5 Guarantee..................................................................................................................28
6 Disposal......................................................................................................................28
7 Declaration of conformity........................................................................................28
8 Maintenance plan......................................................................................................29
9 Disinfection book ......................................................................................................29

Eclips X4, Eclips X4 30°
2012-01
Page 2
Preface
First of all we want to thank you for putting your trust in us by selecting one of our
wheelchairs.
The Vermeiren wheelchairs are the result of many years of research and experience. During
the development, special attention was given to the ease of use and the serviceability of the
wheelchair.
The expected lifetime of your wheelchair is strongly influenced by the care and maintenance
of the wheelchair.
This manual will help you get acquainted with the operation of your wheelchair.
Following the user instructions and the maintenance instructions are an essential part of the
warranty.
This manual reflects the latest product developments. Vermeiren has the right to introduce
changes without the obligation to adapt or replace previously delivered models.
For any further questions, please consult your specialist dealer.

Eclips X4, Eclips X4 30°
2012-01
Page 3
1 Productdescription
1.1 Intended Use
The wheelchair is intended for people with walking difficulties or no walking abilities.
The wheelchair is designed to transport 1 person.
The wheelchair is suited for indoor and outdoor use.
The user can propel the wheelchair by himself or have the wheelchair pushed by an
attendant.
The different types of fittings and accessories, and the modular construction allow full use by
persons disabled by:
•paralysis
•loss of limbs (leg amputation)
•limb defects or deformations
•stiff or damaged joints
•heart insuffiencies and poor blood circulation
•balance disturbances
•cachexia (decrease in muscle)
•and also for aged persons.
When providing for individual requirements:
•body size and weight (max. 150 kg)
•physical and psychological condition
•residential circumstances
•environment
should be taken into consideration.
Your wheelchair should only be used on surfaces where all four wheels are touching the
ground and where there is sufficient contact to propel the wheels equally.
You should practice for use on uneven surfaces (cobblestones, etc.), slopes, curves and to
get past obstacles (curbs, etc.).
The wheelchair should not be used as a ladder, nor is it a transport for heavy or hot objects.
When used on mats, carpeted floors or loose floor coverings, the floor covering can get
damaged.
Use only Vermeiren approved accessories.
The manufacturer is not liable for damage caused by the lack of or improper service or as a
result of not following instructions from this manual.
Compliance with the user and maintenance instructions are an essential part of the
guarantee conditions.

Eclips X4, Eclips X4 30°
2012-01
Page 4
1.2 Technical specifications
Technical terms below are valid for the wheelchair in standard settings.
If other footrests / arm supports or other accessories are used, the tabulated values will change.
Make
Vermeiren
Address
Vermeirenplein 1/15, B
-
2920 Kalmthout
Type
Manual wheelchair
Model
Eclips X4
Maximum occupant mass
150 kg
Description
Dimensions
Effective seat width 390 mm 420 mm 440 mm 460 mm 480 mm 500 mm
550 mm
Overall width (depends on the seat
width) 590 mm 620 mm 640 mm 660 mm 680 mm 700 mm
740 mm
Description
Dimensions Min.
Dimensions Max.
Overall length with footrest 1000 mm 1210 mm
Folded length without footrest 740 mm 910 mm
Folded width 300 mm
Folded height 910 mm 1015 mm
Total mass ± 17,10 kg
Mass of heaviest part 9,40 kg
Masses of parts that can be dismantled
or removed
Foot
supports:
1,90 kg;
Arm supports:
1,65 kg;
Rear wheels: 4,15 kg
Static stability downhill 7,5°(in standard configuration)
Static stability uphill 5°(in standard configuration)
Static stability sideways >16°(in standard configuration)
Obstacle climbing 60 mm
Seat plane angle 0° 13°
Effective seat depth 420 mm 500 mm
Seat surface height at front edge 390 mm 520 mm
Backrest angle 0° 13°
Backrest height 420 mm 460 mm
Distance between footrest and seat 345 mm 460 mm
Angle between seat and footrest 107°
Distance between armrest and seat 220 mm
Front location of armrest structure 340 mm
Handrim diameter 535 mm
Horizontal location of axle (deflection) -47 mm 19 mm
Minimum turning radius 1530 mm
Diameter Krypton PU Rear wheels 24"
Tyre pressure, rear (driving) wheels
(only for air tyres) Max. 3.5 bar
Diameter Krypton PU steering wheels 150 mm 200 mm
Tyre pressure, steering wheels (only
for air tyres) Max. 2.5 bar
Storage and use temperature + 5 °C + 41 °C
Storage and use humidity 30% 70%
We reserve the right to introduce technical changes. Measurement tolerance
±
1
5
m
m / 1,5 kg
/ °
Table 1: Technical specifications Eclips X4

Eclips X4, Eclips X4 30°
2012-01
Page 5
Make
Vermeir
en
Address
Vermeirenplein 1/15, B
-
2920 Kalmthout
Type
Manual wheelchair
Model
Eclips X4
30°
Maximum occupant mass
15
0 kg
Description
Dimensions
Effective seat width 390 mm 420 mm 440 mm 460 mm 480 mm 500 mm 550 mm
Overall width (depends on the seat
width) 590 mm 620 mm 640 mm 660 mm 680 mm 700 mm 740 mm
Description
Dimensions Min.
Dimensions Max.
Overall length with footrest 1000 mm 1210 mm
Folded length without footrest 1000 mm 1210 mm
Folded width 300 mm
Folded height 910 mm 1015 mm
Total mass ± 30 kg
Mass of heaviest part 22,30 kg
Masses of parts that can be
dismantled or removed
Foot
supports:
1,90 kg;
Arm supports:
1,65 kg;
Rear wheels: 4,15 kg
Static stability downhill 7,5°(in standard configuration)
Static stability uphill Axle block backwards: 4°
Axle block forwards:Anti-tipping device must be standard available
Static stability sideways >16°(in standard configuration)
Obstacle climbing 60 mm
Seat plane angle 0° 13°
Effective seat depth 420 mm 500 mm
Seat surface height at front edge 390 mm 520 mm
Backrest angle 0° 43°
Backrest height 420 mm 460 mm
Distance between footrest and seat 345 mm 460 mm
Angle between seat and footrest 107°
Distance between armrest and seat
220 mm
Front location of armrest structure 340 mm
Handrim diameter 535 mm
Horizontal location of axle
(deflection) -47 mm 19 mm
Minimum turning radius 1530 mm
Diameter Krypton PU Rear wheels 24"
Tyre pressure, rear (driving) wheels
Max. 3.5 bar
Diameter Krypton PU steering
wheels 150 mm 200 mm
Tyre pressure, steering wheels Max. 2.5 bar
Gas pressure spring 2 x 275N
Storage and use temperature + 5 °C + 41 °C
Storage and use humidity 30% 70%
We reserve the right to introduce technical changes. Measurement tolerance
±
1
5
m
m / 1,5 kg
/ °
Table 2: Technical specifications Eclips X4 30°

Eclips X4, Eclips X4 30°
2012-01
Page 6
The wheelchair complies to the requirements set up in:
ISO 7176-8: Requirements and test methods for static, impact and fatigue strengths.
ISO 7176-16: Resistance to ignition of upholstered parts
ISO 7176-19: Wheeled mobility devices for use as seats in motor vehicles. (shall be only for
Eclips X4 wheelchair)
1.3 Drawing
1.4 Accessories
The following accessories are available for the Eclips X4, Eclips X4 30°:
•Anterior pelvic belt (B58) for mounting on the tubes of the back
•Anti-tipping device (B78) for mounting on the bottom frame
•Arm supports (B02, B03, B05, B66)
•Footrests (B06, BZ8, BZ7)
•B52 Serum holder
•B74 Drum brakes
•T30 Transit wheelchair
Contact your specialist dealer about other accessories. He will gladly advise you.
1.5 Location identification plate
1= Vermeiren name
2 = Taxi hooks
3 = Identification plate
4 = Name Eclips X4
1 = Cross
2 = Handles
3 = Backrest
4 = Arm pads
5 = Arm supports
6 = Driving wheels (rear wheels)
7 = Hand rims
8 = Brakes
9 = Steering wheels (Front wheels)
10 = Seat
11 = Tip cap
12 = Footrests
13 = Footplate

Eclips X4, Eclips X4 30°
2012-01
Page 7
1.6 Explanation of symbols
Maximum mass
Indoor and outdoor use
Minimum slope
CE conformity
1.7 Safety rules
L To prevent injury and/or damage to your wheelchair, make sure that no objects
and/or body parts are caught in the spokes of the driving wheels.
L The parking brakes should be applied before getting into and out of the wheelchair.
L When getting into and out of the wheelchair, do not stand on the footplates. These
should be folded up beforehand, or the footrests should be swung completely
outwards out of the way.
L Investigate the effects of shifting the centre of gravity on the behavior of the wheelchair,
for example on up or down gradients, on laterally sloping ground, or when overcoming
obstacles. Obtain support from an attendant.
L If you want to pick up something (lying in front of, on the side, or to the rear of the
wheelchair), you should not lean too far out to avoid tipping over.
L When moving through doors, arches, etc. ensure that there is enough room at the sides
so that you do not get your hands or arms caught or crushed and that there is no
damage to the wheelchair.
L Only use your wheelchair according to regulations. For example, avoid uncontrolled
rolling against obstacles (steps, curbs, doorframes, etc) or dropping down from ledges.
The manufacturer cannot assume liability for damage caused by overloading, collision
or other improper use.
L Stairs may only be negotiated when aided by another person. If furnishings like drive-on,
ramps or lifts are available, use them.
L When moving on the public highway, you are subject to the rules of the road.
L When driving your wheelchair, you should not be under the influence of alcohol or
medicine as in the case of driving other vehicles. This also applies to indoor driving.
L When travelling outdoors, adapt your driving to weather and traffic conditions.
L When transporting the wheelchair, never pick it up by grasping movable parts (arm
supports, footrests, etc.)
L To be better visible when driving in the dark, wear the brightest possible clothing or
clothes with reflectors, and check that the reflectors mounted on the sides and rear of
the wheelchair are clearly visible.
L Never exceed the maximum load of your wheelchair.

Eclips X4, Eclips X4 30°
2012-01
Page 8
2 Use
This chapter describes the everyday use. These instructions are for the user and the
specialist dealer.
The wheelchair is delivered fully assembled by your specialist dealer. The instructions
intended for the specialist dealer on how to set up the wheelchair are given in § 3.
2.1 Carrying the wheelchair
The best way to carry the wheelchair is to make use of the wheels and roll the wheelchair.
If this is not possible (e.g. when the rear wheels are taken off for transportation in a car),
firmly grasp the frame on the front and the grips. Do not use the foot or arm supports or the
wheels to grasp the wheelchair.
2.2 Mounting the rear wheels
1. Take the rear wheel and push on button  .
2. Keep the button pushed in and mount the rear
wheels axle till it stops.
3. Release the button.
4. Check that the wheel is secured.
2.3 Unfolding the wheelchair
L
LL
L CAUTION: Risk of clamping – Keep fingers away from moving parts of the
wheelchair.
1. Position yourself behind the wheelchair.
2. Use the handgrips to open the wheelchair as much as possible.
3. Position yourself at the front of the wheelchair.
4. Push both seating tubes down till they are fixed in their position.
5. When the pushbaris available mount the pushbarto the right handle.
2.4 Mounting or removing of the footrests
The mounting of the footrests is done as follows:
1. Hold the footrest sideways at the outside of the
wheelchair frame and mount the tube hood 
into the frame.
2. Swing the footrest inwards till it clicks in
position.
3. Swing the foot plate downwards.
To take off the footrests:
1. Pull handle  .
2. Swing the footrest to the outside of the
wheelchair till it comes loose from the guidance.
3. Pull the footrest tube hood
 out the wheelchair
frame.

Eclips X4, Eclips X4 30°
2012-01
Page 9
2.5 Operating the brakes
L
LL
L WARNING: The brakes are not used to slow down the wheelchair during
movements – Use the brake only to prevent the wheelchair from unintended
movements.
L
LL
L WARNING: Good operation of the brakes is influenced by wear and
contamination of the tires (water, oil, mud, …) – Check the condition of the tires
before each use.
L
LL
L WARNING: The brakes are adjustable and can wear – Check the operation of the
brakes before each use. To apply the brakes:
1. Push the brake handles forward till you feel a
distinctive click.
L
LL
L CAUTION: Risk of unintended movement –
Make sure the wheelchair is on a flat
horizontal surface before releasing the
brakes. Never release both brakes
simultaneously.
To release the brakes:
1. Release one brake by pulling the handle 
backwards.
2. Hold the hand-rim of the released wheel with
your hand.
3. Release the second brake by pulling the handle
backwards.
2.6 Mounting or removing of arm supports
L
LL
L CAUTION: Risk of clamping – Keep fingers, buckles and clothes away from the
bottom side of the arm support.
The arm supports of the wheelchair can be mounted by following instructions.
1. Mount the rear tube of the arm rest in tube hood  . (Fig A)
2. Make sure the arm support is mounted very well.
3. Fold the arm support to the front.
4. Pull lever  on tube hood  upwards. (Fig B)
5. Click the front tube of the arm support in tube hood  . (Fig B)
A
B

Eclips X4, Eclips X4 30°
2012-01
Page 10
To open and remove the arm support:
1. Pull lever  and pull the front of the arm support upwards. (Fig C)
2. Fold the arm support backwards.
3. To remove the arm support, pull the rear of the arm support from tube hood . (Fig D)
2.7 Transfer in and out the wheelchair
L
LL
L CAUTION: In case you cannot perform the transfer in a safe manner, ask
someone to assist you.
L
LL
L CAUTION: Risk of tipping over of the wheelchair – Do not stand on the foot
plates. 1. Position the wheelchair as close as possible to
the chair, couch or bed to/from you wish to
transfer.
2. Check both brakes from the wheelchair are in
the on position.
3. Fold the foot plates upwards to prevent
standing on them.
4. If the transfer is on the side of the wheelchair,
fold the arm support on that side upwards.
(see § 2.6)
5. Transfer to/from the wheelchair.
2.8 Correct position in the wheelchair
Some recommendations for a comfortable use of the wheelchair:
•Position your backside as close as possible to the back rest.
•Make sure your upper legs are horizontal – If needed adjust the length of the
footrests. (see § 3.8.1)
C
D

Eclips X4, Eclips X4 30°
2012-01
Page 11
2.9 Riding the wheelchair
L
LL
L WARNING: Risk of clamping – Prevent your fingers from being caught by the
wheels spokes.
L
LL
L WARNING: Risk of clamping – Be careful passing through restricted passages
(e.g. doors).
L
LL
L WARNING: Risk of burns – Be careful when driving in hot or cold environments
(sunshine, extreme cold, saunas, etc.) for a sufficient amount of time and when
touching - Surfaces can assume the environment temperatures.
1. Release the brakes.
2. Take both hand rims at their highest position.
3. Lean forward and push the hand rims forward until straight arms.
4. Swing your arms loosely back to the hand rims topside and repeat the movement.
2.10 Moving on slopes
L
LL
L WARNING: Control your speed – Moving on slopes as slow as possible.
L
LL
L WARNING: Consider the capacities of your attendant – If your attendant does not
have enough force to control the wheelchair, put on the brakes.
L
LL
L WARNING: Risk of tipping over – Lean forward to move your centre of gravity
forward. To improve a better stability.
1. If available on the wheelchair, wear the safety belt.
2. Do not attempt moving on too high slopes. The maximum
slope angles (upwards and downwards) are mentioned in
table 1 for Eclips X4, table 2 for Eclips X4 30°.
3. Ask an attendant to help you moving on the slope.
4. Lean forward to move your centre of gravity forward.
2.11 Negotiating steps or curbs
2.11.1 Getting down steps or curbs
Riding down low curbs can be done moving forwards. Make sure that the foot rests do not
touch the ground. A practiced user can negotiate small steps or curbs by himself:
L
LL
L WARNING: Risk of tipping over – If you do not have
enough experience with your wheelchair, ask
assistance of an attendant.
1. Bring balance on the rear wheels to reduce the pressure on
the front wheels.
2. Negotiate the curbs.
Higher curbs can be taken forward with an attendant:
1. Ask the attendant to tip the wheelchair slightly backwards.
2. Get past the curbs while moving on the rear wheels.
3. Put the wheelchair back on the four wheels.

Eclips X4, Eclips X4 30°
2012-01
Page 12
An experienced user can negotiate higher curbs by himself. This is
best done backwards.
1. Turn the wheelchair to have the rear wheels facing the
curb.
2. Lean forward to move your centre of gravity forward.
3. Move the wheelchair close to the curbs.
4. Use the hand rim to roll-off wheelchair from the curb in a
controlled manner.
2.11.2 Moving up steps or curbs
Moving up steps or curbs with attendant as follows:
1. Prevent the foot rests from touching the curb.
2. Ask the attendant to tip the wheelchair backwards, just
enough to move the front wheels over the curb.
3. Lean backwards to move your centre of gravity above the rear
wheel.
4. Place the front wheels on the curb.
5. Roll rear wheels of the wheelchair over the curb.
Higher curbs are negotiated backwards:
1. Turn the wheelchair to have the rear wheels facing the curb.
2. Lean backwards and move your centre of gravity above the rear wheels.
3. Ask the attendant to pull the wheelchair on the curb.
4. Take back the normal position in the wheelchair.
An experienced user can negotiate curbs by himself:
L
LL
L WARNING: Risk of tipping over – If you have not enough experience to control
the wheelchair, get help from an attendant.
1. Drive until the curbs.
2. Ensure that the footrest do not touch the curbs.
3. Lean backwards so you are balancing on the rear wheels.
4. Role the front wheels balancing over the curbs.
5. Bend forward for more stability.
6. Role the rear wheels over the curbs.
2.11.3 Taking of stairs
Taking of stairs while you staying in the wheelchair shall be according following rules:
L
LL
L WARNING: Risk of tipping over – Taking of stairs shall always with 2 attendants.
1. Remove the footrests.
2. One attendant tip the wheelchair slightly backwards.
3. The second attendant take the front of the frame.
4. Stay calm, avoid sudden movements and keep your arms inside the wheelchair.
5. Take the steps on the rear wheels of the wheelchair.
6. Mounting the footrests back after taking the stair.

Eclips X4, Eclips X4 30°
2012-01
Page 13
2.12 Fold up the wheelchair
L
LL
L CAUTION: Chance of pinching – Do not place fingers between the components
of the wheelchair.
1. When the pushbar is available remove the pushbar.
2. Fold or remove the footplates (see § 2.4).
3. Take the seat on the front side and backside and pull it up.
4. Push on the handgrips to fold up the wheelchair further.
2.13 Taking off the wheels
To facilitate the transport off the wheelchair the rear wheels can be taken off:
1. Make sure the brakes standing in the off
position.
2. Take the wheelchair to the side frame where
you want to remove the wheel.
3. Press the button  in the center of the wheel
hub.
4. Pull the wheel away from the frame.
2.14 Pushbar
L
LL
L WARNING: Risk of injury - Make sure that all screws are properly tightened.
L
LL
L WARNING: Risk of injury - When equipped with the pushbar, the pushing
pole shall always be mounted (→to increase the stability of the back).
Your wheelchair can have a pushbar. The pushbar increase the stability of the back and offer
you the possibility of pushing the wheelchair by an attendant. To do this, use the pre-
mounted handles.
As there are different pushbars for different seat widths, take care that no tension between
the pushing handles of the back tubes is created.
The mounting of the pushbaris done as follows:
1. Secure the pushbar by fastening the left side to
the end of back tube handle with the Philips
screw in the applicable sunk threads.
2. Screw gently the Philips screw on the right
hand side into the thread of the back tube.
3. Swing the pushbarto the right.
4. Hook the suspension of the pushbar over the
screw thread.
Use the two holes on the left handgrip to adjust
the tension of the backrest.
To take off the pushbar:
1. Loosen the Philips screw on the right handgrip.
2. Remove the hook from the right handgrip.

Eclips X4, Eclips X4 30°
2012-01
Page 14
2.15 Back adjusting (Eclips X4 30°)
L
LL
L WARNING: Risk of tipping over – Be aware that the stability decrease when
adjust the back backwards.
L
LL
L WARNING: Risk of injury – Tighten the parking brakes before adjusting the
backrest inclination.
With the model Eclips X4 30°it is possible to set the backrest backwards with a maximum
inclination of 30°. Be sure that the patient sits in the chair when the attendant shall perform
the backrest adjusting and that the wheelchair does not tip over.
1. Pull handle on both sides towards the grab
handle to adjust the back rest.
2. Pull both back tubes backwards continuously to
a maximum inclination of 30°.
3. The gas pressure spring shall be pressed in.
To set the back to a vertical position, proceed in the
same manner.
If your wheelchair features drum brakes, the
handles are used as brakes; additional levers 
have been mounted for backrest adjusting.
2.16 Transport in the car
L
LL
L WARNING: Risk of injury – See that the wheelchair is attached properly. So you
can avoid injury from the passengers during collision or sudden braking.
L
LL
L WARNING: Risk of injury – Use for attaching the wheelchair and passenger
NEVER the same seatbelt.
To transport the wheelchair in the car use following steps:
1. Remove footrests and accessories.
2. Store footrests and accessories safely.
3. If possible, fold the wheelchair and remove the wheels.
4. Place the wheelchair in the luggage place.
5. If the wheelchair and the passenger compartment is NOT separated, attach the
frame of the wheelchair securely to the vehicle. You can use the available safety
belts in the vehicle.
2.17 Use of the wheelchair as seat in a motor vehicle (Eclips X4)
The wheelchair shall not be used as a seat in a motor vehicle for the Eclips X4 30°.
L
LL
L WARNING: The wheelchair has passed the crash of ISO 7176-19: 2008 and, as
such, has been designed and tested for use only as forward-facing seat in a
motor vehicle.
L
LL
L WARNING: The wheelchair's pelvic belt alone is not suited as an occupant
restraint belt.
The wheelchair is tested using the four-point strap-tie system and a 3-point occupant-
restraint system.
Whenever feasable, use the seat of the vehicle and store the wheelchair in the cargo area.

Eclips X4, Eclips X4 30°
2012-01
Page 15
Steps to secure the wheelchair in a motor vehicle:
1. Check that the vehicle is equipped with a suitable wheelchair tie down and occupant-
restraint system, conform ISO 10542.
2. Check that the components of the wheelchair tie down and occupant restraint system
are not frayed, contaminated, damaged or broken.
3. If equipped with an adjustable seat and/or back tilt, make sure that the wheelchair
user is sitting as upright as possible. If the user's condition prevents this, a risk
assessment should be done to evaluate the user's safety during transit.
4. Remove all mounted accessories such as trays and respiratory equipment, and
secure them in a safe place.
5. Position the wheelchair facing forward in the travelling direction, centrally between
the tie-down rails mounted in the floor of the vehicle.
6. Make sure that the indicated zones around the wheelchair user are clear from rigid
vehicle parts.
7. Mount the front securement straps according to the instructions of the strap-system
manufacturer at the indicated place. (figure 3)
This place is marked on the wheelchair with a symbol. (figure 4)
8. Roll back the wheelchair until the front straps are tight.
9. Apply the wheelchair brake.
10. Mount the back securement straps according to the instructions of the strap-system
manufacturer at the indicated place. (figure 3)
11. This place is marked on the wheelchair with a symbol. (figure 4)
figure 3

Eclips X4, Eclips X4 30°
2012-01
Page 16
Steps to secure the wheelchair user:
1. Remove both arm rests.
2. If present, attach the wheelchair's pelvic belt.
3. Attach the occupant restraint belts according to the instructions of the strap-system
manufacturer.
4. Wear the pelvic belt low across the front of the pelvis, so that the angle of the pelvic
belt is within the preferred zone of 30°to 75°to the horizontal, similar to that shown
below.
5. Asteeper (greater) angle within the preferred zone is desirable.
6. Adjust the belt tightly according to the instructions of the strap-system manufacturer,
consistent with the user's comfort.
7. Ensure that the restraint belt connects in a straight line to the anchor point in the
vehicle and that no bends in the belt are visible, for instance at the axle of the rear
wheel.
8. Install the arm rests, if desired. make sure that belts are not twisted or held away
from the body by wheelchair components such as arm rests or wheels.
3 Installation and adjustment
The instructions in this chapter are for the specialist dealer.
The Vermeiren Lightweight wheelchairs Eclips X4 and Eclips X4 30°has been designed
entirely for your comfort. This wheelchair can be adjusted to individual requirements as
explained below.
To find a service facility or specialist dealer near you, contact the nearest Vermeiren facility.
A list of Vermeiren facilities can be found on the last page.
L
LL
L WARNING: Risk of unsafe settings - Use only the settings described in this
manual.
L
LL
L WARNING: Variation of allowed adjustments can still change the stability of your
wheelchair (tilt back or sideways).

Eclips X4, Eclips X4 30°
2012-01
Page 17
3.1 Tools
To set up the wheelchair the following tools are needed.
•Wrench set n°10 to n°19
•Allen key set n°4 to n°5
•Screwdriver Phillips head
3.2 Manner of delivery
The Vermeiren Eclips X4, Eclips X4 30°shall be delivered with:
•1 frame with arm supports, rear and front wheels (for Eclips X4 30°additionally:
adjusting system 30°back angle)
•1 pair footrests
•Tools
•Manual
•Accessories
3.3 Adjusting the seat height and seat angle
L
LL
L WARNING: Risk of injury - Make sure that all screws are properly tightened with
the appropriate tool.
L
LL
L WARNING: Risk of tipping over - When the driving wheels are adjusted, the
position of the wheels are altered.
The Vermeiren Eclips X4, Eclips X4 30°are adjustable in different seat heights and different
seat angles by changing the wheels position. At each height there is a different setting of the
front and rear wheels.
Seat height Rear wheel Front wheel
Diameter Position
390 mm Position 1 150 mm Hole 4
445 mm Position 2 200 mm Hole 5
471 mm
(Standard) Position 3 200 mm Hole 3
520 mm Position 4 200 mm Hole 2
Table 3: Seat heights by seat angle 4°
Change the seat height and seat angle according following steps:
* Front wheel: 1. Loosen the screws Ⓐfrom the steering wheel
adapter Ⓑ.
2. Choose correct size for the adapter Ⓑand fork.
3. Place the steering wheel adapter in the desired
position.
4. Tighten the screws Ⓐproperly.
or
5. Loosen the screws Ⓓfrom the front fork Ⓔ.
6. Choose the correct position or change diameter
of the wheel in the front fork.
7. Tighten the screws Ⓓproperly.

Eclips X4, Eclips X4 30°
2012-01
Page 18
* Rear wheel:
1. Remove the rear wheels (see § 2.13).
2. Loosen the fixing screws Ⓐfrom the rear axle block Ⓑ.
3. Push the axle block Ⓑupwards or downwards to the desired height.
4. Tighten the screws Ⓐproperly.
5. Mount the rear wheels.
6. Adjust the brakes according § 3.7.
Adjustment of the slope nuts Ⓒfrom the steering wheels.
L
LL
L WARNING: Risk of injury - Make sure that the eccentric screw settings are
identical on both front-wheel adapters and, before using the wheelchair.
This figure illustrates the principle. The position of the screw thread is indicated by a number.
A Shows the frame when the seat is horizontal and the
adapter is perpendicular to the ground.
BShows the frame when the seat is tilted slightly and the
adapter is not perpendicular.
Position 4
Position 3
Position 2
Position 1