Vermeiren Turios User manual

VERMEIREN
Turios
U S E R M A N U A L

Turios
2020-02
Content
1
EN
NL
Content
Content.......................................................................................................................1
1Preface...........................................................................................................2
2Your product..................................................................................................3
2.1 Accessories...................................................................................................3
3Before use .....................................................................................................4
3.1 Intended use .................................................................................................4
3.2 General safety instructions............................................................................4
3.3Symbols on the wheelchair ...........................................................................5
3.4 Transport.......................................................................................................5
3.5 Assembly/Disassembly .................................................................................6
3.6 First use and storage ....................................................................................7
4Using your wheelchair..................................................................................8
4.1 First ride ........................................................................................................8
4.2 Driving outdoors............................................................................................8
4.3 Operating console .........................................................................................9
4.4 Brake and free-wheel lever .........................................................................10
4.5 Parking brakes ............................................................................................ 11
4.6 Moving to/from wheelchair .......................................................................... 11
4.7 Comfort adjustments ...................................................................................12
4.8 Battery status and charging ........................................................................12
5Maintenance ................................................................................................14
5.1 Time of maintenance...................................................................................14
5.2 Instructions for maintenance ....................................................................... 14
5.3 Troubleshooting ..........................................................................................15
5.4 Expected lifespan........................................................................................16
5.5 End of use...................................................................................................16
6Technical specifications.............................................................................17

Turios
2020-02
Preface
2
EN
NL
1 Preface
Congratulations! You are now owner of a Vermeiren wheelchair!
This wheelchair is made by qualified and committed personnel. It is designed and produced
according to high quality standards guarded by Vermeiren.
Thanks for your trust in the products of Vermeiren. To support you on the use of this wheelchair
and its operating options, this manual is offered. Please read it carefully; it will help you to get
familiar with the operation, capabilities and limitations of your wheelchair.
If you still have questions after reading this manual, do not hesitate to contact your specialist
dealer. He/she will be glad to help you on this subject.
Important note
To ensure your safety, and to prolong the lifetime of your product, please take good care of it and
have it checked and serviced on a regular basis.
This manual reflects the latest product developments. Vermeiren has the right to implement
changes to this type of product without being imposed to any obligation to adapt or replace similar
products previously delivered.
Pictures are used to clarify the instructions in this manual. Details of the depicted product may
deviate from your product.
Information available
On our website http://www.vermeiren.com/ you will always find the most recent version of
following information. Please consult this website regularly for possible updates.
Visually impaired people can download the electronic version of this manual and have it read out
by means of a text-to-speech software application.
This user manual
For user and specialist dealer
User manual of applied operating console and battery charger.
For user and specialist dealer
Installation instructions (Instructions for detail adjustments and (dis)assembly)
For specialist dealer
Service manual for wheelchairs
For specialist dealer
EC declaration of conformity

Turios
2020-02
Your product
3
EN
NL
2 Your product
1. Backrest
2. Operating console
3. Armrest
4. Seat
5. Footrest
6. Footplate
7. Safety belt
8. Battery housing
9. Front wheels
10. Driving motors
11. Rear wheels / Driving wheels
12. Front lights (optional)
13. Parking brake
14. Identification plate
2.1 Accessories
The following accessories are available for the electric wheelchair Turios:
•Leg support (BZ7, BZ8)
•Headrest (L55, L58)
•Lights
•Crutch holder
•Cup holder
•Mirror
•Swing-away operating console
•Top case
1
2
3
4
5
6
7
8
9
10
11
12
13
14

Turios
2020-02
Before use
4
EN
NL
3 Before use
3.1 Intended use
In this paragraph a brief description of the intended use of your wheelchair is given. Additionally,
relevant warnings are added to the instructions in the other paragraphs. In this way we would like
to make you aware of the possible misuse that may appear.
•This wheelchair is suitable for indoor and outdoor use.
•This wheelchair is designed and produced solely to transport/transfer one (1) person with a
maximum weight of 130kg. It is not designed for transportation of goods or objects, nor for any
use other than previously described.
•This wheelchair can be operated by the user sitting in the wheelchair, or it can be pushed by
an attendant. You should NOT use this wheelchair without attendant if you suffer from physical
or mental impairments that may put you, or other people, in danger when driving the
wheelchair. For this reason, consult your doctor first and make sure that your specialist dealer
is informed about his advice.
•Only use accessories and spare parts approved by Vermeiren.
•Please read all technical details and limits of your wheelchair in chapter 6.
•The warranty on this product is based on normal use and maintenance as described in this
manual. Damage to your product caused by improper use or lack of maintenance will cause
the warranty to lapse.
3.2 General safety instructions
Risk of injuries and/or damage
Please read and follow the instructions in this manual. Otherwise you may get injured or your
wheelchair may get damaged.
Keep the following general warnings in mind during use:
•Do not use your wheelchair if you are under influence of alcohol, medicines or other
substances that may influence your driving abilities.
•Be aware that some parts of your wheelchair may get very hot or cold due to ambient
temperature, solar radiation, heating devices or due to the motor drive during the ride. Be
careful when touching. Wear protective clothing if the weather is cold. After a ride, wait until
the wheelchair/motor has cooled down.
•Before switching the wheelchair on, be aware of the environment/situation in which you are
located. Adjust your speed to this before driving off. We advise you to use the slowest speed
setting to drive indoors. For outdoor driving you can adjust the speed to a suitable speed at
which you feel comfortable and safe.
•ALWAYS keep in mind that your wheelchair may stop suddenly due to a discharged battery
or a protection that prevents your wheelchair from further damage. Also check the possible
causes mentioned in § 5.3. Use your safety belt to prevent injuries.
•Your wheelchair has been tested for electromagnetic compatibility and complies with the
standard, see chapter 6. Nevertheless, sources of electromagnetic fields may influence the
driving performance of your wheelchair, such as the fields of mobile phones, power
generators or high-power energy sources. On the other hand, the electronics of your
wheelchair can affect other electronic appliances too, such as alarm systems of shops and
automatic doors. We therefore advise you to check your wheelchair regularly for damage and
wear, since these may enlarge the interference (see also chapter 5).
•Only drive on flat surfaces where both driving wheels touch the ground and where there is
sufficient contact to operate the wheelchair safely.
CAUTION

Turios
2020-02
Before use
5
EN
NL
•Alterations or substitutions should not be made to the wheelchair securement points or to
structural and frame parts or components without consulting the wheelchair manufacturer.
•Make sure that your hands, clothes, belts, buckles or jewellery don’t get caught by wheels or
other moving parts during use.
3.3 Symbols on the wheelchair
The symbols in following list are applicable to your wheelchair. Symbols can be found in the
relevant ISO standard (ISO 7000, ISO 7001 and IEC 417).
Maximum weight of the user in kg
Indoor/outdoor use (battery charger excluded)
Indoor use only (battery charger)
Maximum safe slope in ° (degrees).
Maximum speed
Type designation
Risk of entrapment
3.4 Transport
Risk of damage
Take action to protect the wheelchair from being damaged during transport.
3.4.1 Moving out of the way
Use the operating console to drive the wheelchair to its destination.
Otherwise, put the wheelchair in free-wheel mode (see §4.4) and use the push bar to move it.
3.4.2 Transport by aircraft
Since the wheelchair is equipped with non-spillable AGM batteries, it is possible to transport the
wheelchair (as a whole) by aircraft. Consult your airline for the correct handling procedures before
booking your flight. Before handing your wheelchair over to the airport personnel, disconnect the
battery from the wheelchair, see installation manual.
3.4.3 Transport by vehicle, as luggage
The best way to transport your electric wheelchair in the car is to drive it by using ramps. If you
are not experienced to drive the electric wheelchair using ramps, you can put the wheelchair in
CAUTION
Risk of injuries
•Do NOT use your wheelchair as seat in a vehicle, see the following symbol.
•Never use the same safety belt for passenger and wheelchair.
WARNING

Turios
2020-02
Before use
6
EN
NL
neutral mode and push the wheelchair in the car using ramps. If necessary, disassemble the
wheelchair.
1. As the wheelchair user, transfer to a car seat, see §4.6.
2. Remove all moveable parts prior to transport (footrests, arm supports, etc.).
3. Store moveable parts safely behind the passenger seat or in the luggage compartment.
4. Drive or push the electric wheelchair in the car using ramps, or lift the wheelchair in the car
with the help of 2 persons by grasping the fixed parts of the frames.
5. Attach the solid parts of the frame securely to the vehicle.
6. Place the wheelchair in drive mode (engaging the parking brakes) and check that the operating
console is switched off.
3.5 Assembly/Disassembly
Risk of injuries
•Make sure that your fingers, clothes, buckles won’t get trapped during (dis)assembly.
Your dealer delivers the wheelchair fully assembled and explains the various operating elements
and their use. We also provide a further, detailed explanation of the different parts here for
transport purposes.
To assemble the electric wheelchair:
1. Mount the arm supports (paragraph 3.5.1).
2. Mount the footrests (paragraph 3.5.2).
To disassemble the electric wheelchair do the reverse of the above instructions.
3.5.1 Mounting or removing the arm support
Risk of injuries and/or damage
•Check that the arm pads are at the same height on each side.
Mount the armrest (1) by sliding the support rod (2) down into the
frame (3).
To remove the armrest (1), lift it up and out of the seat frame.
3.5.2 Mounting or removing the footrest
To install
1. Hold footrest (4) sideways and hang it in footrest support (5).
2. Swing the footrest inwards until it clicks in position.
To remove
1. Pull footrest lever (6) and swing footrest (4) outwards.
2. Lift the footrest to remove it.
CAUTION
CAUTION
1
2
3
4
5
6

Turios
2020-02
Before use
7
EN
NL
3.6 First use and storage
Risk of battery damage
•Never completely discharge the battery.
•Do not interrupt the charging cycle; only disconnect the battery charger when the battery is
fully charged.
•Make sure that your wheelchair is stored dry to prevent mould from growing and the
upholstery from being damaged.
•Check the technical details for storage, see chapter 6.
Ensure that the battery has been fully charged before using your wheelchair, ask your dealer if
this has already been done or not. To charge, follow the charging instructions in §4.8.
CAUTION

Turios
2020-02
Using your wheelchair
8
EN
NL
4 Using your wheelchair
Risk of injuries
•First read previous chapters and inform yourself about the intended use. Do NOT use your
wheelchair unless you have read and fully understood all instructions.
•Also read the instructions in the operator console manual and battery charger manual!
•In case of doubts or questions, do not hesitate to contact your local specialist dealer, your
care provider or technical adviser to help you with this.
4.1 First ride
Risk of injuries and damage
•Always keep the swing range of footrest and operating console in mind to prevent bystanders
from being injured or objects from being damaged.
•Always unplug the battery charger from the wheelchair before starting to drive.
•Make sure that you are familiar with the operation of your wheelchair before using it in
crowded and possibly dangerous places. First exercise at a specious, open area with
little bystanders.
•Investigate the effects of shifting the centre of gravity on the behaviour of the wheelchair,
for example on up or down gradients, on laterally sloping ground, or when overcoming
obstacles. Obtain support from an attendant.
•The surface of the controller gets slightly warm during use.
•While driving backwards, the speed is reduced.
1. Make sure that:
•the wheelchair is on a flat surface;
•the battery is fully loaded, see § 4.8;
•The motor is coupled, see § 4.4;
•the tyres have the correct tyre pressure, see § 5.2.1;
•the wheelchair is adapted to your needs and comfort, see §4.7;
•you have the proper sitting position, see § 4.6.
2. Follow the instructions in the operating console manual.
3. Switch on your wheelchair.
4. Turn the speed control to the lowest speed setting.
5. Exercise how to drive and make adjustments to the wheelchair.
6. If you feel confident enough, you can try to drive at higher speed.
7. Now try to turn, in forward and backward direction. Repeat this a few times.
8. Make sure that your wheelchair stands stable, when ending the ride.
9. Switch off your wheelchair.
4.2 Driving outdoors
Risk of accident - Adjust your driving behaviour and speed.
•Take the local road traffic law into consideration; it may differ per country. This counts for
driving on pavements, unpaved roads or paved roadways.
•Do not drive on roads with heavy traffic.
•Take the weather conditions into consideration. Avoid driving by moist weather, extreme heat,
snow, black ice, freezing temperatures; see technical specifications in chapter 6.
•Even with your wheelchair lights on, it is not suitable to drive on public roads at poor visibility
(darkness, mist, twilight). Make sure that you are well visible, also during daylight hours, by
WARNING
CAUTION
WARNING

Turios
2020-02
Using your wheelchair
9
EN
NL
using fluorescent clothing and/or by using own lighting at the front and rear side of the
wheelchair.
•Be aware of other road users to whom your wheelchair may be an obstacle. Pay special
attention during turning and reversing. If you are not acquainted with how to drive backwards,
first practice in an open area. Indicate the direction you are intending to go before turning.
•Try to drive straight in small passages to prevent getting trapped.
•Keep the braking distance in mind. Be aware that the braking distance depends on speed,
surface, weather conditions, slope and weight of the user.
4.2.1 Cope with slopes, kerbs, obstacles or ramps
Risk of injuries by unexpected movement
•Use a restraining safety belt to secure yourself sitting in the wheelchair.
•Pay attention if the road is sandy, has soft ground, holes or gaps that may cause entrapment
of the wheels and/or decreasing of the traction of the driving wheels.
•Do NOT drive on slopes, obstacles, steps or kerbs larger than the size described in the
technical specifications in chapter 6.
•Always approach a kerb from the front.
•Do not put your wheelchair in free-wheel mode on a slope. The wheelchair may start moving,
causing injuries to you or bystanders.
•Do not use your wheelchair on an escalator or stairs.
•Only use ramps approved by Vermeiren and do not exceed their maximum load.
Risk of damage
•Always park your electric wheelchair on horizontal flat surfaces and on sites that are easily
accessible.
•If necessary, take a short run-up to speed up the wheelchair to mount a slope, obstacle, kerb
or ramp. Prevent that you or your wheelchair has to cope with a large recoil.
•Make sure that the wheelchair does not touch the ground or ramp due to the inclination of the
wheelchair.
•Be aware that the braking distance on downhill slopes can be significantly larger than on level
ground.
Procedure
•Start your drive according to the instructions in § 4.1, step 1.
•To move the wheelchair up or down stairs/steps, use lifting equipment or a ramp. If these
are not available, it can be lifted manually by at least two persons, grasping the frame firmly
with both hands. Do not use the backrest, footplate(s), armrests, or wheels to grasp the
wheelchair.
•To cope with obstacles or inclinations:
1. Adjust the wheelchair to its most stable position, see § 4.6.
2. Drive as slow as possible to cope with the obstacle or inclination.
4.3 Operating console
Risk of injuries or damage
•Be aware that the stability decreases when the wheelchair is adjusted from sitting-straight to
inclined position.
•Make sure there is enough space around the wheelchair to operate backrest and seat.
CAUTION
CAUTION
CAUTION
When you stop on a slope, the brake will work automatically to prevent the wheelchair from
running forward or backward.

Turios
2020-02
Using your wheelchair
10
EN
NL
How to use the operating console is described in a specific user manual, enclosed with the
delivery of your wheelchair. If this manual is missing, contact your specialist dealer
immediately.
Put the joystick in the neutral (central) position before pressing the on/off button, otherwise
the electronics will be blocked. To release this block, switch the operating console off and
on again.
Technical protections
The operating console enables you to control all driving components and motors to adjust your
body position. For your own safety, and to prevent that the wheelchair gets damaged, movements
are monitored by the electronics. This may result in block of movement, speed decrease or
complete stop. Consult the user manual of the operating console for more information.
To avoid accidental battery run down, your wheelchair is equipped with an automatic power
shutdown system. This system switches off the operating console automatically when it is not
operated for a while. If this occurs, simply switch your console back on.
4.4 Brake and free-wheel lever
Risk of injuries or damage
•Only operate the free-wheel lever when your wheelchair is turned OFF. An attendant should
operate the free-wheel lever. NEVER operate it from sitting position.
•Do not use the free-wheel mode on slopes and inclinations, see symbol on motor:
Make sure that the free-wheel lever is in its braking position BEFORE switching the
wheelchair ON. Electromagnetic brakes do NOT function if the wheelchair is in free-wheel
mode. This is indicated on the operating console. Driving is not possible.
Your wheelchair is equipped with electromagnetic brakes. The working of the brakes depends on
the position of the free-wheel lever (1).
The EM brakes function automatically, only if free-wheel lever (1) is in braking position. In this
situation, the brakes start braking if:
•the wheelchair is OFF;
•the wheelchair is ON and the
joystick is released.
Releasing the joystick makes the
wheelchair stop gently and activates
the brakes.
Operation of free-wheel lever:
•Turn levers to the rear to put the
wheelchair in free-wheel mode.
Now, the motor is disconnected.
The wheelchair can be moved
manually.
•Turn levers inwards to connect
the motor to the drive. This
should be done before starting
the wheelchair.
CAUTION
Neutral
Drive
1
1

Turios
2020-02
Using your wheelchair
11
EN
NL
4.5 Parking brakes
Risk of injuries and/or damage
•The brakes are not meant to slow down the wheelchair during movements. Use the brakes
only to prevent the wheelchair from making unintended movements.
•Good operation of the brakes is influenced by wear and contamination of the tires (water, oil,
mud, …). Check the condition of the tires and the operation of the brakes before each use.
•Make sure the wheelchair is on a flat horizontal surface before releasing the brakes. Never
release both brakes simultaneously.
To apply the brakes:
1. Push the brake levers (2) forward until you feel a distinctive
click.
To release the brakes:
1. Release the brakes one by one by pulling the lever (2)
backwards.
4.6 Moving to/from wheelchair
Risk of injuries or damage
•In case you cannot perform the transfer in a safe manner, ask someone to assist you.
•Do not stand on the footplate(s) during transfer into or out of the wheelchair.
Transfer
1. Position the wheelchair as close as possible to you when sitting in your chair, couch, seat or
bed.
2. Apply the brakes by turning the free-wheel lever to braking position and/or by activating the
parking brakes, see § 4.4 and §4.5.
3. Fold the footplate(s) upwards to prevent standing on them.
4. If necessary, remove one armrest to make room, see § 3.5.1.
5. Transfer to/from the wheelchair using the strength of your arms or with the help of attendant(s)
or lifting equipment.
Sitting in the wheelchair
1. Sit down on the seat with your lower back against the backrest.
2. Turn the footplate(s) down and put your feet on the footplates.
3. Replace the armrest, if applicable.
4. Make sure that your upper legs are horizontal and that your feet are in a comfortable position.
Adjust if necessary.
5. Make sure that your arms are bent and are resting comfortably on the arm pads. Adjust if
necessary.
Adjusting to stable position
For transport purposes and when you need to negotiate obstacles, the wheelchair must be
adjusted to maximise its stability:
•Backrest upright
•Footplate folded up
CAUTION
CAUTION
2

Turios
2020-02
Using your wheelchair
12
EN
NL
4.7 Comfort adjustments
Risk of injuries or damage
•The following comfort adjustments can be done by the attendant or caretaker. All other
adjustments are done by your specialist dealer according to the installation instructions, see
preface.
•Make sure that your fingers, clothes, buckles don’t get trapped during adjustment.
4.7.1 Backrest inclination (manual version)
1. Pull the strap at the bottom of the backrest to unlock the mechanism.
2. Adjust the backrest to the desired position (0° - 32°, 4 steps of 8°).
3. Release the strap. Make sure that the backrest is well secured.
4.8 Battery status and charging
Risk of injuries and damage due to fire
•Only use the battery charger delivered with the wheelchair. The use of any other charger
may be dangerous (fire hazard).
•The battery charger is only intended to charge the batteries delivered with the wheelchair,
not to charge any other batteries.
•Do not adapt any of the delivered parts, like cables, plugs or battery charger. Never open or
change the battery or the connection points.
•Protect the battery and battery charger against flames, high and low temperatures (see
chapter 6), moisture, sunshine, severe shocks (for example dropping). Do NOT use the
battery if this has been the case.
•Charge the battery with the battery charger, indoors, in a well-ventilated area, out of
children's reach.
•First read the user instruction of the applied battery charger before charging the wheelchair’s
battery. For more information, contact your specialist dealer or consult our website
http://www.vermeiren.com/
Risk of damage
•Battery self-discharge and the quiescent current of the connected users will drain the battery
charge slowly. The battery may be irreversibly damaged if the battery is fully discharged.
Therefore, make sure that the battery is charged on time (see manual of operating console).
•Read the storage and maintenance instructions in § 5 and technical details in chapter 6.
•Only disconnect the battery charger when the battery is fully charged.
•Do not charge batteries below 0°C. Move the battery to a warmer place and start charging.
•Keep the connection point for the battery charger free of dust and other contamination.
•In case of any problems whereby the battery cannot be charged according to following
instructions, please contact your specialist dealer.
•For instructions on how to change the batteries, see the installation manual.
For all information on battery status indication, please read the manual of the operating
console.
It is recommended to unplug the battery charger from the mains when not in use. This is to
prevent unnecessary energy consumption.
CAUTION
WARNING
CAUTION

Turios
2020-02
Using your wheelchair
13
EN
NL
To charge the battery:
1. FIRST connect the battery charger to a 230V AC power socket. Use the battery charger
directly, without extension cord, on the power supply (without time switch).
2. Plug the adapter in the charging point of the operating console.
3. Wait until the battery is fully charged. Consult the battery charger manual for more information.
4. Disconnect the battery charger.
5. Remove the battery charger from the socket, let it cool down and store it in the charger pocket.

Turios
2020-02
Maintenance
14
EN
NL
5 Maintenance
5.1 Time of maintenance
Risk of injuries and damage
Repairs and replacements may only be undertaken by trained persons and only genuine
replacement parts of Vermeiren should be used.
The last page of this manual contains a registration form for the specialist dealer to record
each service.
The service frequency depends on the frequency and intensity of use. Contact your dealer to
agree to a common timetable for inspection/maintenance/repair.
Read the user instructions of the applied battery charger regarding maintenance.
For the maintenance manual, refer to the Vermeiren website: www.vermeiren.com.
Before each use
Inspect the following points:
•All parts: present, undamaged and unworn.
•All parts: clean, see § 5.2.2.
•Wheels, seat, arm rests, footrests and headrest (if applied): well secured.
•Battery status: charge the battery when necessary, see §4.8.
•Operating console, battery, power module, motors, battery charger, lights and relevant
cables: no damage such as wires that have become frayed, broken or exposed.
•Condition of wheels/tyres, see § 5.2.1.
•Condition of frame parts: no deformation, instability, weakness or loose connections.
•Seat, backrest, arm pads, calf pads and head rest (if applied): no excessive wear (like
dented spots, damage or tears).
Contact your specialist dealer for possible repairs or part replacements.
Every month
If your wheelchair is stored for a longer period, you still need to charge the batteries every month.
It is also possible to keep the battery charger connected to the battery and the mains during this
period. For more information, see § 4.8.
Yearly or more often
Have your wheelchair inspected and serviced by your specialist dealer, at least once a year, or
more often. The minimum maintenance frequency depends on use and should therefore be
commonly agreed upon with your specialist dealer.
If stored
Make sure that your wheelchair is stored in a dry environment to prevent mould from growing,
or the upholstery from being damaged.
5.2 Instructions for maintenance
5.2.1 Wheels and tyres
Proper working of the brakes depends on the state of the tyres, that can change due to wear
and contamination (water, oil, mud, …).
CAUTION

Turios
2020-02
Maintenance
15
EN
NL
•Keep your wheels free of wires, hair, sand and fibres.
•Check the profile of the tyres. If the tread depth is less than 1 mm, the tyres need to be
replaced. Contact your specialist dealer for this matter.
•Inflate the pneumatic tyres to the correct pressure (see pressure indication on the tyres).
•For instructions on how to change the tyres, see the installation manual.
5.2.2 Cleaning
Risk of damage by moisture
•Keep the operating console clean and protect it from water and rain.
•Never use a hose or high-pressure cleaner to clean the wheelchair.
Wipe all rigid parts of the wheelchair with a damp cloth (not drenched). If necessary, use a mild
soap, suitable for varnishes and synthetics.
The upholstery can be cleaned with lukewarm water and a mild soap. Do not use abrasive
cleaning agents to clean.
Keep the ventilation openings of the battery charger clean and free of accumulated dust. Blow
away the dust and clean the battery charger enclosure with a slightly moistened cloth, if required.
5.2.3 Disinfection
Risk of damage
Disinfections may only be undertaken by trained persons. Consult your specialist dealer.
5.3 Troubleshooting
Even if you use your wheelchair properly, a technical problem may occur despite this.
In this case, contact your local specialist dealer.
Risk of injuries and damage to the wheelchair
•NEVER attempt to repair your wheelchair yourself.
•For failures in the operating console you need to contact your specialist dealer.
He/She will decide if the console needs to be reprogrammed.
In case of failure, a fault code is displayed on the operating console.
For an overview of all fault codes on the operating console, please read the manual of the
operating console.
The following symptoms may indicate a serious problem. Therefore, always contact your
specialist dealer if you spot any of the following deviations:
•Strange sound;
•Frayed/damaged wiring harnesses;
•Cracked or broken connectors;
•Uneven tread wear at one of the tyres;
•Jerky movements;
•Wheelchair deflects to one side;
•Damaged or broken wheel assemblies;
•Wheelchair does not switch on (blown fuse);
•Wheelchair is powered but does not move, see 4.4.
CAUTION
CAUTION
WARNING

Turios
2020-02
Maintenance
16
EN
NL
5.4 Expected lifespan
The average lifespan of your wheelchair is 5 years. Depending on the frequency of use, driving
circumstances and maintenance, the lifespan of your wheelchair will increase or decrease.
5.5 Reuse
Before each reuse, have the wheelchair disinfected, inspected and serviced according to the
instructions in §5.1 and §5.2.
5.6 End of use
At end of life, you need to dispose of your wheelchair according to the local environmental
legislation. The best way to do so, is to disassemble the wheelchair to facilitate the transport of
recyclable parts.

Turios
2020-02
Technical specifications
17
EN
NL
6 Technical specifications
The technical details below are only valid for this wheelchair, at standard settings and optimal
ambient conditions. Take these details into account during use. The values are no longer
applicable if your wheelchair has been modified, damaged, or is severely worn. Be aware that the
driving performance is influenced by ambient temperature, humidity, slopes (driving up/down),
type of surface and battery status.
Table 1: Technical specifications
Brand
Vermeiren
Address
Vermeirenplein 1/15, B-2920 Kalmthout
Type
Electric wheelchair, Class B
Model
Turios
Maximum occupant mass
130 kg
Description
Dimensions
Overall length with leg rest
Manual
Electric
1070 mm
1060 mm
Overall width
580 mm
580 mm
640 mm
Total mass
Approx. 105,8 kg
Energy consumption *
35 km
Rated slope
6°
Obstacle climbing
50 mm
Maximum speed forward
6km/h
10 km/h
Min. braking distance from max.
speed
2100 mm
Seat plane angle Manual
Electric
0° - 2° - 4° - 6°
0° - 6°
Effective seat depth Manual
Electric
380 mm – 500 mm
405 mm – 525 mm
Effective seat width
390 mm
450 mm
510 mm
Seat surface height at front edge
Manual
Electric
440 mm – 490 mm – 540 mm
530 mm – 560 mm – 590 mm
Backrest angle Manual
Electric
0° - 8° - 16° - 24° - 32°
0 - 32°
Backrest height Manual
Electric
585 mm
550 mm
Footrest to seat distance
320 mm – 420 mm
Leg to seat surface angle
114°
Armrest to seat distance
260 mm – 335 mm
Front location of armrest structure
Manual
Electric
340 mm – 430 mm
Max. 320 mm
Minimum turning radius
Approx. 1600 mm
Ground clearance
60 mm (antitipping)
100 mm (middle)

Turios
2020-02
Technical specifications
18
EN
NL
Brand
Vermeiren
Address
Vermeirenplein 1/15, B-2920 Kalmthout
Type
Electric wheelchair, Class B
Model
Turios
Maximum occupant mass
130 kg
Diameter rear wheels
350 mm
Type of rear wheels **
Air tyres
Diameter front wheels
200 mm – 230 mm – 260 mm
Type of front wheels **
Air tyres
Electrical description
Battery (Non-spillable AGM battery,
maintenance-free)
35 Ah
44 Ah (gel, optional)
50 Ah
Driving motors
6 km/h: 2 x 150W
10 km/h: 2 x 450W
Power module Blow fuse
150 AMP
Strength tests according to
ISO 7176-8
Tests of power and control system
according to
ISO 7176-14
Ignitability of upholstery according to
EN1021-2:2006
EMC compliance
ISO 7176-21
Degree of protection
IPX4
Noise level
< 65 dB (A)
Storage and use temperature
+5 °C ~ +41 °C
Operating temperature for
electronics
-10°C ~ +40°C
Storage and use humidity
30% ~ 70%
We reserve the right to introduce technical changes. Measurement tolerance ± 15 mm / 1,5 kg / 1,5° .
* The theoretical driving distance will be reduced if the wheelchair is used frequently on slopes, rough
ground or to climb curbs.
**Since different tyres may be used, please note the correct operating pressure of the tyres you use. For
other tyre diameters refer to your specialist dealer.