Vermont Castings SB60 User manual

1
VCG Biltmore Series • SB60/SB80 • 4013-300 Installers Manual • Rev A • 02/18/15
Installation and service of this replace should be
performed by qualied personnel. Vermont Cast-
ings Group recommends NFI certied profession-
als, or technicians supervised by an
NFI certied professional.
WOODBURNING FIREPLACE
Fire Risk.
WARNING
For use with solid wood fuel only.
Other fuels may overre and generate
poisonous gases (i.e. carbon monoxide).
Model(s):
Installation Manual
Installation and Fireplace Setup
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
replace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other ammable
materials.
• Keep clothing, furniture, draperies and other ammable
materials away.
INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
SB60
SB80
NOTICE: DO NOT discard this manual!
• DO NOT store or use gasoline or other am-
mable vapors and liquids in the vicinity of this
or any other appliance.
• DO NOT overre. Overring will void your
warranty.
• Comply with all minimum clearances to com-
bustibles as specied. Failure to comply may
cause house re.
WARNING: If the information in these
instructions is not followed exactly, a re
or explosion may result causing property
damage, personal injury, or death.
This replace uses SL1100 Series Chimney
2” CLEARANCE TO COMBUSTIBLES AND BUILDING INSULATION FROM CHIMNEY REQUIRED.

2VCG Biltmore Series • SB60/SB80 • 4013-300 Installers Manual • Rev A • 02/18/15
Safety Alert Key:
• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
• NOTICE: Indicates practices which may cause damage to the replace or to property.
Table of Contents
1 Product Specic & Important Safety Information
A. Fireplace Certication 4
B. Non-Combustible Materials 4
C. Combustible Materials 4
2 Getting Started
A. Typical Fireplace System 5
B. Design and Installation Considerations 6
1. Selecting Fireplace Locations 6
2. Locating Fireplace & Chimney 7
C. Tools and Supplies Needed 8
D. Inspect Fireplace and Components 8
E. Fireplace System Requirements 8
3 Framing and Clearances
A. Fireplace Dimensions 9
B. Clearances 10
Minimum Clearances to Combustibles 10
C. Construct the Chase 11
D. Unpack the Fireplace (I60 only) 12
E. Unpack the Fireplace (I80 only) 12
F. Frame the Fireplace 13
G. Secure and Level the Fireplace 14
H. Protective Metal Hearth Strips 14
I. Outside Air Kit 15
4 Chimney and Termination Requirements
A. Chimney Requirements 16
B. Offsets/Returns 17
C. Termination Requirements 18
5 Chimney Installation
A. Typical Chimney System 19
B. Assemble Chimney Sections 20
C. Install Chimney Air Kit 20
D. Secure Offset/Return 21
E. Install Ceiling Firestops 21
F. Install Attic Insulation Shield 22
G. Roof Penetration 23
H. Install Chase/Chase Top 23
I. Termination Cap Requirements 24
J. Install Termination Cap 24
6 Shrouds
A. Radiation Shield 26
B. Field Constructed Shrouds 26
1. Open Top Shroud 26
2. Mailbox Style Shroud 27
3. Roofed Style Shroud 27
7 Finishing
A. Finishing Material 28
B. Hearth Extension, Building and Finishing 29
1. Fireplace Installed Flush on the Floor
and Hearth Extension Raised to Bottom
of Firebox Opening 30
2. Raised Hearth Extension and Raised Fireplace 31
3. Fireplace Opening and Hearth Extension Flush
with the Floor 32
C. Non-Combustible Sealant Material 32
D. Sidewalls/Surrounds 33
E. Mantel and Wall Projections 34
8 Fireplace Setup
A. Gas Log/Lighter Provision 35
B. Wood Burning Inserts 35
C. Install the Refractory (I80 only) 36
9 Reference Materials
A. Chimney Components 37
B. Optional Components 40

3
VCG Biltmore Series • SB60/SB80 • 4013-300 Installers Manual • Rev A • 02/18/15
Customer:
Lot/Address
Model (circle one): SB60 SB80
YES IF NO, WHY?
Protective hearth strips installed per manual requirements. (Pg. 14)
Outside air kit installed. (Pg. 15)
Attic insulation shield installed.
Shroud is installed properly per instructions.
WARNING! Risk of Fire or Explosion! Failure to install fireplace acording to these instructions can lead to a fire or
explosion.
Verified that the chase is insulated and sealed. (Pg. 11)
Verified clearances to combustibles. (Pg. 10)
Fireplace is leveled and secured. (Pg. 14)
Hearth extension size/height decided. (Pg. 29)
Chimney configuration complies with diagrams.
Chimney installed, locked and secured in place with proper clearance.
Chimney air kit installed.
Firestops installed.
ATTENTION INSTALLER:
Follow this Standard Work Checklist
This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this installation
manual.
Date Installed:
Location of Fireplace:
Installer:
Dealer/Distributor Phone #
Serial #:
Roof flashing installed.
Termination installed.
Fireplace Install
Chimney Section 4 & 5 (Pg. 16)
Shrouds Section 6 (Pg. 26)
Fi i hi
S ti 7 (P 28)
Hearth extension installed per manual requirements.
Comments communicated to party responsible
4013-302 • Rev A • 2-18-15
__________________________ by ______________________on _________
(Builder/Gen. Contractor) (Installer) (Date)
Comments: Further description of the issues, who is responsible (Installer/Builder/Other Trades, etc.) and corrective action needed:
Manual bag and all of its contents are removed from the fireplace and given to the party
responsible for use and operation.
• That this checklist remain visible at all times on the fireplace until the installation is complete.
• Photographing the installation and copying this checklist for your file.
Combustible materials not installed in non-combustible areas.
Vermont Castings Group recommends the following:
Finishing Section 7 (Pg. 28)
Fireplace Setup Section 8 (Pg. 35)
Verified all clearances meet installation manual requirements.
Mantels and wall projections comply with installation manual requirements.
All packaging and protective materials removed.
Optional doors properly installed.
Molded brick panels installed correctly.
Grate is properly installed.
Firescreen installed properly.

4VCG Biltmore Series • SB60/SB80 • 4013-300 Installers Manual • Rev A • 02/18/15
WARNING! Risk of Fire! Vermont Castings Group dis-
claims any responsibility for, and the warranty and agency
listing will be voided by the following actions.
DO NOT:
• installoroperatedamagedreplace
• modifyreplace
• install other than as instructed by Vermont Castings
Group
• operate the fireplace without fully assembling all
components
• overre
• installanycomponentnotapprovedbyVermontCastings
Group
• installpartsorcomponentsnotListedorapproved
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. For
assistance or additional information, consult a qualied
installer, service agency or your dealer.
B. Non-Combustible Materials
• Materials which will not ignite and burn, composed of
any combination of the following:
- Steel - Iron
- Brick - Tile
- Concrete - Slate
- Glass - Plasters
• Materials reported as passing ASTM E 136, Standard
Test Method for Behavior of Metals, in a Vertical Tube
Furnace at 750° C
C. Combustible Materials
• Materials made of or surfaced with any of the following
materials:
- Wood - Compressed paper
- Plant bers - Plastic
- Plywood/OSB - Sheet rock (drywall)
• Any material that can ignite and burn; ame proofed or
not, plastered or un-plastered
1 Product Specic & Important Safety Information
A. Fireplace Certication
This replace may be installed in sleeping rooms. This
replace is not approved for manufactured housing. If in-
stalled with a gas log set, provisions for the National Fuel
Gas Code must be met.
This replace has been tested and listed for use with
the optional components specied in this manual. These
optional components may be purchased separately and
installed at a later date. An outside air kit, gas insert, gas
log set or gas log-lighter should be installed at the time of
replace installation.
This replace system has been tested and listed in accor-
dance with UL 127 and ULC-S610 standards by Under-
writers Laboratories Inc. for installation and operation in
the United States and Canada.

5
VCG Biltmore Series • SB60/SB80 • 4013-300 Installers Manual • Rev A • 02/18/15
2 Getting Started
A. Typical Fireplace System
Figure 2.1 Typical Fireplace System
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
))
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
Non-combustible
roof flashing maintains
minimum clearance
around chimney
Additional lateral
support for chimney
above roof (or enclosed
in chase) if needed
Ceiling firestop
on floor of attic
Support straps
on rafter support
chimney
Termination cap
Chimney penetrates roof
preferably without affecting
roof rafters
Offset & Return (with hanger straps)
Framing headed off
in ceiling joists
Enclosed space above
and around fireplace
Mantel and surround
Decorative facing
and trim
Hearth extension
Factory-built fireplace
Protective metal
hearth strip(s)
Outside
combustion air
Combustible framing/header
on top of V-shaped standoffs
Chimney system
Attic insulation shield
must be used here to keep
insulation away from chimney
if attic is insulated
Storm Collar
Chimney Air Kit
Required in
Canada. Outlet
must be no
less than 4 ft.
(1.22 m) off
ground level.

6VCG Biltmore Series • SB60/SB80 • 4013-300 Installers Manual • Rev A • 02/18/15
F
D
E
A
In an exterior
chase or projecting
into a garage
Across a
corner
As a room
divider
Along a wall
G
B A
G
G
B
A
48 in.
(1219 mm)
min.
H
A
H
Note: SB60 - 1 in. (25 mm)
SB80 - 1 1/2 in. (38 mm)
minimum distance from sides
& back of fireplace to
combustible materials.
Both - 1/2 in. (13 mm)
minimum at nailing flanges.
C
H
B*
1/2 in. (13 mm)
all configurations
*8 in. (203 mm) extra space
included for outside air
connection. If outside air duct has
no bend, this dimension may be
reduced as long as minimum
clearances are met.
A B C D E F G H
inches 45 1/2 53 1/2 85 42 1/2 19 3/8 60 1/8 28
mm 1156 1359 2159 1080 492 1527 711
inches
52
59 1/2 92 3/4 46 3/8 21 1/2 65 5/8 28 1/2
mm 1308 1511 2356 1178 546 1667 724
Model
SB60
SB80
24 in. (610 mm)
Minimum from FP opening to a
ny
perpendicular wall.
51 1/2
Figure 2.2 Fireplace Locations
NOTICE:
• Illustrationsandphotosreecttypicalinstallationsand
are FORDESIGNPURPOSESONLY.
• Illustrations/diagramsarenotdrawntoscale.
• Actualinstallation/appearancemayvaryduetoindividual
design preference.
• VermontCastingsGroupreservestherighttoalterits
products.
NOTICE: In addition to these framing dimensions, also
reference the following section:
• Clearances (Section 3).
NOTICE:
SB60-Aminimum1in.airclearanceattheback
andaminimum1in.airclearancetothesidesof
thereplaceassemblymustbemaintained.
SB80-Aminimum11/2in.airclearanceatthe
backandaminimum11/2in.airclearancetothe
sidesofthereplaceassemblymustbemain-
tained
Chimney sections at any level require a 2
in. minimum air space clearance between
the framing and chimney sections.
B. Design and Installation Considerations
NOTICE: Checkbuildingcodespriortoinstallation.
• Installation MUST comply with local, regional, state and
national codes and regulations.
• Consult insurance carrier, local building inspector, re
ofcials or authorities having jurisdiction over restrictions,
installation inspection and permits.
• Before installing, determine the following:
- Where the replace is to be installed.
- The vent system conguration to be used.
- Gas supply piping.
- Electrical wiring.
- Framing and nishing details.
- Whether optional accessories - devices such as a
fan, wall switch or remote control - are desired.
1. Selecting Fireplace Locations
This replace may be used as a room divider, installed
along a wall, across a corner or used in an exterior chase.
See Figure 2.2.
Locating the replace in a basement, near frequently
opened doors, central heat outlets or returns, or other
locations of considerable air movement can affect the
performance.
Consideration should be given to these factors before
deciding on a location.

7
VCG Biltmore Series • SB60/SB80 • 4013-300 Installers Manual • Rev A • 02/18/15
2. Locating Fireplace & Chimney
Location of the replace and chimney will affect perfor-
mance.
• Install within the warm airspace enclosed by the building
envelope. This helps to produce more draft, especially
during lighting and die-down of the re.
• Installing the replace in a basement is not recommended.
• Penetrate the highest part of the roof. This minimizes
the effects of wind loading.
• Locate termination cap away from trees, adjacent
structures, uneven roof lines and other obstructions.
• Minimize the use of chimney offsets.
• Consider the replace location relative to oor and ceiling
and attic joists.
• Take into consideration the termination requirements in
Sections 4 and 5.
Marginal Location:
• Below peak
Location NOT recommended:
• Not the highest point of the roof
• Wind loading possible
Multi-level Roofs
Windward
Leeward
Recommended Location:
• Above peak
Recommended:
• Insulated exterior chase
in cooler climates
Recommended Location:
• Above peak
• Inside heated space
Location NOT recommended:
• Too close to tree
• Below adjacent structure
• Lower roof line
• Avoid outside wall
Marginal Location:
• Wind loading possible
Figure 2.3 Recommended Chimney Locations
• Install the outside air kit with the intake facing prevailing
winds during the heating season.
• Ensure adequate outdoor air for all combustion
appliances and exhaust equipment.
• Ensure furnace and air conditioning return vents are not
located in the immediate vicinity of the replace.
• Avoid installing the replace near doors, walkways or
small isolated spaces.
• Recessed lighting should be a “sealed can” design.
• Attic hatches weather stripped or sealed.
• Attic mounted duct work and air handler joints and seams
taped or sealed.

8VCG Biltmore Series • SB60/SB80 • 4013-300 Installers Manual • Rev A • 02/18/15
C. Tools and Supplies Needed
Before beginning the installation be sure the following
tools and building supplies are available:
Reciprocating saw Framing material
Pliers Non-combustible sealant
Hammer Gloves
Phillips screwdriver Framing square
Flat blade screwdriver Electric drill and bits
Plumb line Safety glasses
Level Tape measure
1/2-3/4 in. length, #6 or #8 self-drilling screws
Misc. screws and nails
D. Inspect Fireplace and Components
WARNING! Risk of Fire and/or Explosion! Damaged
parts could impair safe operation. DO NOT install dam-
aged,incompleteorsubstitutecomponents.Keepre-
place dry.
• Inspect replace for damage.
• Vent system components and doors are shipped in
separate packages.
• Report to your dealer any parts damaged in shipment.
• Read all the instructions before starting the
installation. Follow these instructions carefully
during the installation to ensure maximum safety
and benet.
E. Fireplace System Requirements
The VCG replace system requirements consist of the
following:
• Fireplace
- Refractory (included with replace)
- Firescreen (included with replace)
- Hearth Extension
• Outside Air System
- Air Inlet Hood (included with replace)
- Flex (required, sold separately)
• Chimney System
- Chimney air kit (required in Canada, sold separately)
- Attic Insulation Shield (included with replace)
- Chimney termination cap (required, sold separately)
- SLA10 adapter (required in Canada, sold separately)
• Non-combustible nish material

9
VCG Biltmore Series • SB60/SB80 • 4013-300 Installers Manual • Rev A • 02/18/15
3 Framing and Clearances
A. Fireplace Dimensions
Gas
Knockout
8-5/8 in.
(219 mm)
9-5/8 in.
(244 mm)
9-1/2 in.
(241 mm)
Outside Air
9-1/4 in.
(235 mm)
Gas Knockout
18-1/2 in.
(470 mm)
8-5/8 in.
(219 mm)
49-5/8 in.
(1260 mm) 28-1/2 in.
(724 mm)
55-1/2 in.
(1410 mm)
(effective height)
49-1/8 in.
(1248 mm)
59-1/4 in.
(1505 mm)
7-5/8 in.
(194 mm) 36 in.
(914 mm)
28-5/8 in.
(727 mm)
14-3/8 in.
(365 mm)
44-1/2 in.
(1130 mm)
27-1/2 in.
(699 mm)
9-1/2 in.
(241 mm)
Figure 3.1 Fireplace Dimensions
28-1/2 in.
(724 mm)
55-1/2 in.
(1410 mm)
(Efective Height
49-1/8 in.
(1248 mm)
49-5/8 in.
(1260 mm)
59-1/4 in.
(1505 mm)
7-5/8 in.
(194 mm) 42 in.
(1067 mm)
Gas
Knockout
18-1/2 in.
(470 mm)
8-5/8 in.
(219 mm)
Gas
Knockout
8-5/8 in.
(219 mm)
9-5/8 in.
(244 mm)
9-1/2 in.
(241 mm)
9-1/4 in.
(235 mm)
Outside
Air
34-1/2 in.
(876 mm)
9-1/2 in.
(241 mm)
27-1/2 in.
(699 mm)
50-1/2 in.
(1283 mm)
SB60
SB80

10 VCG Biltmore Series • SB60/SB80 • 4013-300 Installers Manual • Rev A • 02/18/15
B. Clearances
WARNING! Risk of Fire!
You must comply with all minimum air space clearances
tocombustiblesasspeciedinFigure3.2.DO NOTpack
required air spaces with insulation or other materials.
Framing or nishing material used on the front of, or in
frontof,thereplacecloserthantheminimumslistedmust
be constucted entirely of non-combustible materials (i.e.,
steel studs, concrete board, etc.). Failure to comply may
causere.
Figure 3.2 Clearances to Combustible Materials
Minimum Clearances to Combustibles
WITHIN ENCLOSURE AREA
Fireplace to backwall (I60) 1 in. (25 mm)
Fireplace to backwall (I80) 1 1/2 in. (38 mm)
Fireplace to sidewall (I60) 1 in. (25 mm)
Fireplace to sidewall (I80) 1 1/2 in. (38 mm)
Top standoffs to header 0 in. (0 mm)
Door opening to sidewall 24 in. (610 mm)
MANTEL
Mantel minimum height 12 in. (305 mm)
above opening
Maximum mantel depth 12 in. (305 mm)
(insulation)
0 in. to level
of standoffs
Attic
Insulation
Shield
(ceiling)
(roof)
(attic)
(ceiling)
Ceiling Firestop
Offset/Return (secured
with hanger straps)
Storm Collar
Roof Flashing
Clearance to back &
sides of appliance
I60 - 1 in. (25 mm)
I80 - 1 1/2 in. (38 mm)
(except at nailing flanges
where it is 1/2 in. [13 mm])
Must have 2 in. (51 mm)
minimum clearance
to header
0 in.
to floor
2 in. (51 mm) min.
Shaded areas
represent
2 in. (51 mm) min.
air space clearance
required around pipe
Combustible Object
48 in.
1219 mm
Adapter attached here (not shown)
Note: Chimney air kit and 11-10
in./279-254 mm adapter are
not shown, but are required in
Canada.