Vertiv LIEBERT PSA-PH User manual

PSA650-PH User Manual (v1/071823) 1
VERTIV™ LIEBERT® PSA-PH
650VA/360W, 230V, Line Interactive UPS
User Manual
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This manual contains important instructions that should be
followed during installation and maintenance
• Intended for installation in a controlled environment.
• Maximum ambient temperature 104°F (40°C)
CAUTION! To prevent the risk of fire or electric shock, install in a
temperature and humidity controlled indoor area free of
conductive contaminants. (See the specifications for the
acceptable temperature and humidity range.)
CAUTION! To reduce the risk of overheating the UPS, do not
cover the UPS cooling vents and avoid exposing the unit to direct
sunlight or installing the unit near heat emitting appliances such
as space heaters or furnaces.
CAUTION! Do not attach non-computer related items, such as
medical equipment, life-support equipment, microwave ovens, or
vacuum cleaners to UPS.
CAUTION! Do not plug the UPS input into its own output.
CAUTION! Do not allow liquids or any foreign object to enter the
UPS. Do not place beverages or any other liquid-containing
vessels on or near the unit.
CAUTION! In the event of an emergency, press the OFF button
and disconnect the power cord from the AC power supply to
properly disable the UPS.
CAUTION! Do not attach a power strip or surge suppressor to the
UPS.
CAUTION! If the UPS is with metal chassis, for safety purpose,
grounding is a must during UPS installation in order to reduce
leakage current below 3.5mA.
CAUTION! When replacing the batteries, use the same number
and type of batteries.
CAUTION! Internal battery voltage is 12VDC. Sealed, lead-acid,
6-cell battery.
CAUTION! Electric shock hazard. When UPS is disconnected from
the mains source, hazardous voltage may still be available through
the batteries. Disconnect all battery connectors from battery
terminals prior to doing any maintenance or service works.
CAUTION! Servicing of batteries should be performed or
supervised by personnel knowledgeable of batteries and the
required precautions. Keep unauthorized personnel away from
batteries.
CAUTION! Do not dispose of batteries in a fire. The battery may
explode. Do not open or mutilate the battery or batteries.
Released electrolyte is harmful to the skin and eyes.
CAUTION! Unplug the UPS prior to cleaning and do not use liquid
or spray detergent.
CAUTION! A battery can present a risk of electric shock and high
short circuit current . the following precaution should be observed
before replacing batteries:
1) Remove watches, rings, or other metal objects.
2) Use tools with insulated handles.
3) Wear rubber gloves and boots.
4) Do not lay tools or metal parts on top of batteries.
5) Disconnect charging source prior to connecting or
disconnecting batteries terminal.
SETUP
Step 1 Inspect the Package
Inspect the package and the UPS upon receipt.
Notify the carrier and dealer of visible damage.
Step 2 Decide Where to Place the UPS
The UPS must be placed indoors, protected from water, direct
sunlight and excessive heat. Provide at least 7.8” (20cm) of
clearance on all sides of the unit for proper ventilation.
Step 3 Charge the UPS Battery Before Use
The UPS battery is fully charged before shipping. However, some
charge may be lost during shipping and the battery should be
recharged prior to use.
• Plug-in the UPS AC input cord to the wall outlet. For the
best results, we recommend charging the battery at least
four (4) hours before initial use. The unit charges its battery
while connecting to the utility.
Step 4 Start the UPS
After the battery is fully charged:
• Turn on the UPS by pressing the ON/OFF button. (see below
figure) LED should be illuminated (green), indicating the UPS
is operating in Normal mode.
Step 5 Connect the Loads
The UPS has four (4) battery backup standard outlets that
provide power when the UPS operates on battery.
(see Figure 2 on next page)
• Plug the loads into the battery backup outlets on
the rear of the UPS.
CAUTION: NEVER connect a laser printer or scanner to the UPS
unit. This may cause the damage of the unit.
4
HRS
UPS Quick-Start Guide On/O Button

VERTIV™ LIEBERT® PSA-PH, 650VA/360W, 230V LINE INTERACTIVE UPS
User Manual
Vertiv.com
© 2023 Vertiv Group Corp. All rights reserved. Vertiv™ and the Vertiv logo are trademarks or registered trademarks of Vertiv Group Corp. While every precaution has been taken to ensure accuracy
and completeness herein, Vertiv Group Corp. assumes no responsibility, and disclaims all liability, for damages resulting from use of this information or for any errors or omissions.
Specifications are subject to change without notice. Vertiv™ Liebert® PSA-PH (PSA650-PH)_UM (v1/071823)
2PSA650-PH User Manual (v1/071823)
UPS CONTROL AND CONNECTIONS
LED Color Mode of Operation
Green Normal Mode
Yellow Battery Mode
Red Fault Mode
UPS Status, Alarm and Alerts
Condition LED Color Solid/Flashing Audible Alarm
Normal Mode Green Solid (None)
Battery Mode Yellow Flashes Every 10 seconds
Battery Low Yellow Flashes Every 1 second
Overload at Normal Mode Green Solid Every 0.5 second
Overload at Battery Mode Yellow Flashes UPS shuts down immediately
Fault Red Solid Continuous until UPS shuts down
Figures 2 - Rear Panel
Input Fuse
Figures 1 - Front Panel LED
TROUBLESHOOTING
If the UPS malfunctions during operation, check the following chart for proper adjustment. For further assistance, please contact your
local Vertiv representative.
Problem Possible Causes Solutions
Utility is normal, but LED is not illuminated
• Battery capacity may be low
• The UPS battery reached end-of-life
• The UPS may not be turned on
• Recharge the UPS at least 6 hours
• Replace the battery with the same type of battery
• Press the ON/OFF button to turn on the UPS
Alarm buzzer beeps continuously although
utility power is normal • The UPS may be overloaded • Disconnect some equipment from the UPS
UPS does not provide expected backup-time
• The UPS may be overloaded
• Battery voltage may be low
• The UPS battery reached end-of-life
• Disconnect some equipment from the UPS
• Recharge the UPS at least 6 hours
• Replace the battery with the same type of batter
Utility is normal, but LED flashes • The power cord may not be connected properly • Connect the power cord securely into a wall outlet
Specifications
Model Number PSA650-PH
Capacity (VA/W) 650/360
Unit Weight, kg. (lb.) 3.8 (8.4)
Unit Dimensions, W × D × H mm (in.) 101 × 280 × 142 (4.0 × 11.0 × 5.6)
Shipping Weight, kg. (lb.) 4.3 (9.5)
Shipping Dimension, W × D × H mm (in.) 142 × 326 × 213 (5.6 × 12.8 × 8.4)
Input Voltage Range 170–280VAC, Single Phase
Input Frequency 50/60 Hz (Auto Sensing)
Online Frequency Range (50Hz/60Hz) 45~55Hz ± 1Hz/ 55~65Hz ± 1Hz
Output Voltage (Utility Power Normal) 230VAC, Single Phase
Output Voltage (Battery Operation) 230 ± 10%
On-Battery Wave Form Stepped Sinewave
Output Frequency Battery Mode 50Hz / 60Hz ± 1Hz
Battery Type, VDC × Ah × Quantity 12V × 7 Ah × 1
Typical Recharge Time 6~8 Hours to 90%
Operating Temperature, °C 0 to 40
Storage Temperature, °C -20 to 50
Operating/Storage Relative Humidity 0~90%, Non-condensing
Runtime Table
Load (%) Load (W) Runtime Approx.
(minutes)
10% 36 W 48
20% 72 W 20
30% 108 W 10
50% 180 W 3
4x Battery Backup Outlet
AC Input
LED
On/O Button