Vestil EHLTD Series User manual

TABLE OF CONTENTS Rev. 2/2/2022 EHLTD MANUAL
TABLE OF CONTENTS Copyright 2021 Vestil Manufacturing Corp. Page 1 of 28
EHLTD-Series Double Scissor Electric-Hydraulic Lift Tables
Receiving Instructions
After delivery, remove the packaging from the product. Inspect the product closely to determine
whether it sustained damage during transport. If damage is discovered, record a complete description of
it on the bill of lading. If the product is undamaged, discard the packaging.
NOTE: The end-user is solely responsible for confirming that product design, use, and maintenance comply
with laws, regulations, codes, and mandatory standards applied where the product is used.
Technical Service & Replacement Parts
For answers to questions not addressed in these instructions and to order replacement parts, labels,
and accessories, call our Technical Service and Parts Department at [phone]. The Department can
also be contacted online at https://www.vestil.com/page-parts-request.php.
Electronic Copies of Instruction Manuals
Additional copies of this instruction manual may be downloaded from https://www.vestil.com/page-
manuals.php.
Vestil Manufacturing Corp.
2999 North Wayne Street, P.O. Box 507, Angola, IN 46703
Telephone: [phone] -or- Toll Free [phone]
Fax: [phone]
Web:
www.vestilmfg.com e-mail: [email protected]
Table of Contents
Page
Signal Words……………………..…………………………….……………………………..……….………….….
2
Safety Instructions and Notice about Proper Use and Maintenance.....…………..……….…………...
2- 3
Complete Unit Exploded Views and Bills of Materials………………………..…………..…………………
4 - 15
Electric Circuit Diagrams: 115VAC; 203-230VAC; 3-Phase…………………………………………...…….
16, 17
Motor Lead Connections………………………………………………………………………………………….
18
Control Voltage Transformer………………………………………………………………………………………
18
Power Unit Subassembly: Power Unit; Manifold Assembly……………………………………….….……..
19
Hydraulic Schematic……………………………………………………………………………………………….
20
Installing the Table…...……………………………………………………………………………………………..
20, 21
Record of Satisfactory Condition………………………………………………………………………………..
22
Operating the Table……………………………………………………………...…………………..………...….
22, 23
Inspecting and Maintaining the Table……………………..……………………………………….……….…
23, 24, 25
Bleeding Air from the Hydraulic Cylinder(s)..……………………………………………………..….……….
25
Troubleshooting Guide…………………………………………………………………………….……..…..……
26
Labeling Diagram.…………..………………………………………..……………............................................
27
Limited Warranty…………………………………………….……………………………………………..…....…
28

TABLE OF CONTENTS Rev. 2/2/2022 EHLTD MANUAL
TABLE OF CONTENTS Copyright 2021 Vestil Manufacturing Corp. Page 2 of 28
SIGNAL WORDS
This manual uses SIGNAL WORDS to indicate the likelihood of personal injuries, as well as the probable
seriousness of those injuries, if the product is misused in the ways described. Other signal words call
attention to uses of the product likely to cause property damage. The following are signal words used in
this manual and their definitions.
SAFETY INSTRUCTIONS
Vestil strives to identify all hazards associated with the use of our products. However, material
handling is dangerous and no manual can address every risk. The most effective way to avoid injury is
for the end-user to exercise sound judgment whenever using this product.
Improper or careless operation might result in serious personal injuries or death.
•Read the entire manual before assembling, installing, using, or servicing the table. A copy of this
manual must be available at all times to persons who assemble, install, use, or service the table. Read
the manual whenever necessary to refresh your understanding of use and maintenance procedures.
•This product presents pinch point and hydraulic pressure hazards to the user and bystanders. ALWAYS
follow the instructions provided in this manual to avoid injury.
•This product must be solidly anchored to the supporting surface before it is used. DO NOT use the
table until it is solidly anchored to the floor. See INSTALLING THE TABLE on p. 20-21.
•DO NOT operate a lift table with its perimeter toe guard removed, disabled, or inoperable.
•DO NOT attempt to lift a load that weighs more than the capacity of your table. The table is labeled
with its capacity. See Label 1153 as shown in LABELING DIAGRAM on p. 27. Handle only stable and
safely arranged loads within the capacity of the table.
•DO NOT allow people to stand or sit on either the table or the load. DO NOT lift people with the table.
•Stand clear of the table while raising or lowering the tabletop. Particularly avoid pivot/pinch points
while the tabletop rises and lowers.
•DO NOT attempt to lift an overhanging or cantilevered load.
•DO NOT reach through the legs or crawl under the tabletop unless maintenance stops are deployed.
•DO NOT use the table in corrosive environments.
•ONLY install the table on compacted, improved surfaces capable of supporting the combined weight
of the table plus a maximum rated load. The installation surface must be even and level.
•DO NOT perform maintenance on this table or its power unit UNLESS the table is unloaded and
maintenance stops are in place. ONLY install manufacturer-approved replacement parts.
•Center and evenly distribute loads on the tabletop.
•Strap loads to the tabletop when necessary to prevent rolling or sliding.
•Inspect the unit according to the INSPECTING & MAINTAINING THE TABLE instructions on 23, 24, & 25.
DO NOT use the table unless it is in SATISFACTORY CONDITION. See RECORD, p. 22.
•Observe the tabletop while raising and lowering it. It should rise smoothly and evenly from side-to-side.
Watch for binding or jerky movement. Listen for unusual noises. Tag the unit "Out of order" & remove it
from service if you notice damage or observe (see or hear) anything about the table that is abnormal.
•Always watch the load carefully while raising and lowering the tabletop.
•DO NOT continue to press the UP button if the tabletop is fully elevated.
•Before leaving the table unattended, unload it and relieve hydraulic pressure by pressing the DOWN
button and holding it until the tabletop is completely lowered.
•DO NOT use the table UNLESS all labels are in place & easily readable. See LABELING DIAGRAM, p. 27.
•DO NOT modify this product in any way. Modifications automatically void the LIMITED WARRANTY and
might make the table unsafe to use.
WARNING
!
DANGER
Identifies a hazardous situation which, if not avoided, WILL result in DEATH or
SERIOUS INJURY. Use of this signal word is limited to the most extreme situations.
WARNING
Identifies a hazardous situation which, if not avoided, COULD result in DEATH or
SERIOUS INJURY.
CAUTION
Indicates a hazardous situation which, if not avoided, COULD result in MINOR or
MODERATE injury.
NOTICE
Identifies practices likely to result in product/property damage, such as
operation that might damage the product.
!
!
!

TABLE OF CONTENTS Rev. 2/2/2022 EHLTD MANUAL
TABLE OF CONTENTS Copyright 2021 Vestil Manufacturing Corp. Page 3 of 28
NOTICE
Proper use and maintenance are essential for this product to function properly.
•Periodically lubricate pivot points with bearing grease.
•Keep the product clean & dry. Only install and use this table indoors.
•Only use manufacturer-approved replacement parts. Order replacement/spare parts for this
equipment by contacting the TECHNICAL SERVICE DEPARTMENT.
•DO NOT use brake fluid or jack oils in the hydraulic system. If oil is needed, only use an anti-wear
hydraulic oil with a viscosity grade of 150 SUS at 100°F, (ISO 32 cSt @ 40°C), or Dexron transmission fluid.
•Contact the manufacturer for SDS (Safety Data Sheet) documentation

TABLE OF CONTENTS Rev. 2/2/2022 EHLTD MANUAL
TABLE OF CONTENTS Copyright 2021 Vestil Manufacturing Corp. Page 4 of 28
EXPLODED VIEW: EHLTD-4848-0.7-70 + ROTATE (26-006-114-001)

TABLE OF CONTENTS Rev. 2/2/2022 EHLTD MANUAL
TABLE OF CONTENTS Copyright 2021 Vestil Manufacturing Corp. Page 5 of 28
BILL OF MATERIALS: EHLTD-4848-0.7/1.7/2.7/3.7-70 + ROTATE (26-006-114-001)
ITEM
PART NO.
DESCRIPTION
QTY.
1
26-002-110
26-002-120
26-002-130
26-002-140
FINAL ASSEMBLY W/O POWER UNIT
EHLTD-0.7-70 + ROTATE
EHLTD-1.7-70 + ROTATE
EHLTD-2.7-70 + ROTATE
EHLTD-3.7-70 + ROTATE
1
1
1
1
2
26-514-001
WELDMENT, FRAME ASSEMBLY
1
3 26-510-047
26-510-048
WELDMENT, LOWER INNER LEG, 21 5/8 C/C
EHLTD-0.7-70 + ROTATE & EHLTD-1.7-70 + ROTATE
EHLTD-2.7-70 + ROTATE & EHLTD-3.7-70 + ROTATE
1
1
4
26-510-045 WELDMENT, LOWER OUTER LEG, 21 5/8 C/C 1
5 26-510-050
26-510-051
WELDMENT, UPPER INNER LEG, 21 5/8 C/C
EHLTD-0.7-70 + ROTATE & EHLTD-1.7-70 + ROTATE
EHLTD-2.7-70 + ROTATE & EHLTD-3.7-70 + ROTATE
1
1
6
26-510-046
WELDMENT, UPPER OUTER LEG, 21 5/8 C/C
1
7
01-527-001 ROLLER W/ BUSHING 4
8
01-115-001 WASHER, THRUST BEARING, 1 1/8 ID 12
9
26-117-001 SNAP RING, Ø1 1/8 PIN TRUARC #5160-112 4
10
99-521-906-002
99-521-901-002
99-521-906-001
99-521-901-001
CYLINDER, HYDRAULIC
EHLTD-0.7-70 + ROTATE: Ø2 1/2" X 10" RAM STYLE, MACHINED END, 3GPM VF
EHLTD-1.7-70 + ROTATE: Ø3" x 10" RAM STYLE, MACHINED END, 3GPM VF
EHLTD-2.7.70 + ROTATE: Ø2 1/2" X 10" RAM STYLE, MACHINED END, 2GPM VF
EHLTD-3.7-70 + ROTATE: Ø3" x 10" RAM STYLE, MACHINED END, 2GPM VF
1
1
2
2
11
26-112-005
PIN, PIVOT, TORSION END
2
12
26-112-006
PIN, DBL SCISSOR PIVOT
4
13
01-112-008
PIN, SCISSOR PIVOT
2
14
26-112-001
PIN, HINGE
4
15
99-115-001
WASHER, THRUST
4
16
01-115-002 WASHER, THRUST BEARING 8
17
33454 NARROW MACHINERY BUSHING, PLAIN FINISH, 1 3/4" X 18 GA 8
18
68021 EXTERNAL RETAINING RING, PHOSPHATE FINISH, 1-1/8" 8
19 24-612-003
24-612-003
WELDMENT, CYLINDER PIN
EHLTD-0.7-70 + ROTATE & EHLTD-1.7-70 + ROTATE
EHLTD-2.7-70 + ROTATE & EHLTD-3.7-70 + ROTATE
1
2
20 32415
32415
Ø5/16 - 18 x 1/2 HWH THREAD CUTTING SCREW, TYPE F, ZINC
EHLTD-0.7-70 + ROTATE & EHLTD-1.7-70 + ROTATE
EHLTD-2.7-70 + ROTATE & EHLTD-3.7-70 + ROTATE
1
2
21
01-118-001
BOLT, CYLINDER RETAINING
2
22
36209
1/2 - 13 HEX JAM NUT PLAIN, GRADE A
2
23
26335
SHOULDER SCREW, GRADE 2, 0.375x2" LG
2
24
37021 NYLON INSERT LOCK NUT, GRADE 2, ZINC FINISH, 5/16"-18 6
25
33004 FLAT WASHER, USS, ZINC PLATED, Ø1/4" 6
26
64134
SPRING PIN
2
27
26333
SHOULDER SCREW, GRADE 2, 0.375x1.5" LG
4
28
26-513-013
WELDMENT, DECK, 48" X 48", ROTATE
1
29
01-515-013
SUB-ASSEMBLY, TOE GUARD, 48" X 48", INCLUDES HARDWARE & SWITCHES
1

TABLE OF CONTENTS Rev. 2/2/2022 EHLTD MANUAL
TABLE OF CONTENTS Copyright 2021 Vestil Manufacturing Corp. Page 6 of 28
EXPLODED VIEW: EHLTD-4848-1/2/3/4-70 (26-006-111-002)

TABLE OF CONTENTS Rev. 2/2/2022 EHLTD MANUAL
TABLE OF CONTENTS Copyright 2021 Vestil Manufacturing Corp. Page 7 of 28
BILL OF MATERIALS: EHLTD-4848-1/2/3/4-70 (26-006-111-002)
ITEM
PART NO.
DESCRIPTION
QTY.
1
26-002-110
26-002-120
26-002-130
26-002-140
FINAL ASSEMBLY W/O POWER UNIT
EHLTD-4848-1-70
EHLTD-4848-2-70
EHLTD-4848-3-70
EHLTD-4848-4-70
1
1
1
1
2
26-514-001
WELDMENT, FRAME ASSEMBLY
1
3 26-510-047
26-510-048
WELDMENT, LOWER INNER LEG, 21 5/8 C/C
EHLTD-4848-1-70 & EHLTD-4848-2-70
EHLTD-4848-3-70 & EHLTD-4848-4-70
1
1
4
26-510-045
WELDMENT, LOWER OUTER LEG, 21 5/8 C/C
1
5 26-510-050
26-510-051
WELDMENT, UPPER INNER LEG, 21 5/8 C/C
EHLTD-4848-1-70 & EHLTD-4848-2-70
EHLTD-4848-3-70 & EHLTD-4848-4-70
1
1
6
26-510-046
WELDMENT, UPPER OUTER LEG, 21 5/8 C/C
1
7
01-527-001
ROLLER W/ BUSHING
4
8
01-115-001
WASHER, THRUST BEARING, 1 1/8 ID
12
9
68021
EXTERNAL RETAINING RING, PHOSPHATE FINISH, 1-1/8"
12
10
99-521-906-002
99-521-901-002
99-521-906-001
99-521-901-001
CYLINDER, HYDRAULIC
EHLTD-4848-1-70: Ø2 1/2" X 10" RAM STYLE, MACHINED END, 3GPM VF
EHLTD-4848-2-70: Ø3" x 10" RAM STYLE, MACHINED END, 3PM VF
EHLTD-4848-3-70: Ø2 1/2" X 10" RAM STYLE, MACHINED END, 2GPM VF
EHLTD-4848-4-70: Ø3" x 10" RAM STYLE, MACHINED END, 2PM VF
1
1
2
2
11
26-112-005
PIN, PIVOT, TORSION END
2
12
26-112-006
PIN, DBL SCISSOR PIVOT
4
13
01-112-008
PIN, SCISSOR PIVOT
2
14
26-112-001
PIN, HINGE
4
15
99-115-001
WASHER, THRUST
4
16
01-115-002
WASHER, THRUST BEARING
8
17
33454
NARROW MACHINERY BUSHING, PLAIN FINISH, 1 3/4" X 18 GA
8
18 24-612-003
24-612-003
WELDMENT, CYLINDER PIN
EHLTD-4848-1-70 & EHLTD-4848-2-70
EHLTD-4848-3-70 & EHLTD-4848-4-70
1
2
19 32415
32415
Ø5/16 - 18 x 1/2 HWH THREAD CUTTING SCREW, TYPE F, ZINC
EHLTD-4848-1-70 & EHLTD-4848-2-70
EHLTD-4848-3-70 & EHLTD-4848-4-70
1
2
20
01-118-001
BOLT, CYLINDER RETAINING
2
21
36209
1/2 - 13 HEX JAM NUT PLAIN
2
22
26335
SHOULDER SCREW 0.375x2" LG
2
23
37021
NYLON INSERT LOCK NUT, GRADE 2, ZINC FINISH, 5/16"-18
6
24
33004
FLAT WASHER, USS, ZINC PLATED, Ø1/4"
6
25
64134
SPRING PIN
2
26
26333
SHOULDER SCREW 0.375x1.5" LG
4
27
26-513-005
WELDMENT, DECK
1
28
01-515-013
SUB-ASSEMBLY, TOE GUARD, 48" X 48", INCLUDES HARDWARE & SWITCHES
1

TABLE OF CONTENTS Rev. 2/2/2022 EHLTD MANUAL
TABLE OF CONTENTS Copyright 2021 Vestil Manufacturing Corp. Page 8 of 28
EXPLODED VIEW: EHLTD-4848-5-70 (26-006-151-002)

TABLE OF CONTENTS Rev. 2/2/2022 EHLTD MANUAL
TABLE OF CONTENTS Copyright 2021 Vestil Manufacturing Corp. Page 9 of 28
BILL OF MATERIALS: EHLTD-4848-5-70 (26-006-151-002)
ITEM PART NO. DESCRIPTION QTY.
1 26-002-150 FINAL ASSEMBLY W/O POWER UNIT 1
2 26-514-001 WELDMENT, FRAME ASSEMBLY 1
3 26-510-049 WELDMENT, LOWER INNER LEG, 21 5/8 C/C 1
4 26-510-045 WELDMENT, LOWER OUTER LEG, 21 5/8 C/C 1
5 26-510-052 WELDMENT, UPPER INNER LEG, 21 5/8 C/C 1
6 26-510-046 WELDMENT, UPPER OUTER LEG, 21 5/8 C/C 1
7 01-527-001 ROLLER W/ BUSHING 4
8 01-115-001 WASHER, THRUST BEARING, 1 1/8 ID 12
9 68021 EXTERNAL RETAINING RING, PHOSPHATE FINISH, 1-1/8" 12
10 99-521-906-001
CYLINDER, HYDRAULIC, Ø2 1/2" X 10" RAM STYLE, MACHINED END, 2GPM
VF
3
11 26-112-005 PIN, PIVOT, TORSION END 2
12 26-112-006 PIN, DBL SCISSOR PIVOT 4
13 01-112-008 PIN, SCISSOR PIVOT 2
14 26-112-001 PIN, HINGE 4
15 99-115-001 WASHER, THRUST 4
16 01-115-002 WASHER, THRUST BEARING 8
17 33454 NARROW MACHINERY BUSHING, PLAIN FINISH, 1 3/4" X 18 GA 8
18 01-118-001 BOLT, CYLINDER RETAINING 3
19 36209 1/2 - 13 HEX JAM NUT PLAIN 3
20 26335 SHOULDER SCREW 0.375x2" LG 2
21 37021 NYLON INSERT LOCK NUT, GRADE 2, ZINC FINISH, 5/16"-18 6
22 33004 FLAT WASHER, USS, ZINC PLATED, Ø1/4" 6
23 64134 SPRING PIN 2
24 26333 SHOULDER SCREW 0.375x1.5" LG 4
25 24-112-003 PIN, CYLINDER PIVOT 1
26 26-513-005 WELDMENT, DECK 1
27 01-515-013 SUB-ASSEMBLY, TOE GUARD, 48" X 48", INCLUDES HARDWARE & SWITCHES 1

TABLE OF CONTENTS Rev. 2/2/2022 EHLTD MANUAL
TABLE OF CONTENTS Copyright 2021 Vestil Manufacturing Corp. Page 10 of 28
EXPLODED VIEW: EHLTD-4864-1-84 (26-006-061-002)

TABLE OF CONTENTS Rev. 2/2/2022 EHLTD MANUAL
TABLE OF CONTENTS Copyright 2021 Vestil Manufacturing Corp. Page 11 of 28
BILL OF MATERIALS: EHLTD-4864-1-84 (26-006-061-002)
ITEM NO PART NO DESCRIPTION QTY.
126-02-60 FINAL ASSEMBLY W/O POWER UNIT 1
226-514-002 WELDMENT, FRAME ASSEMBLY 1
326-510-027 WELDMENT, LOWER INNER LEGS, 29 5/8 C/C 1
426-510-030 WELDMENT, LOWER OUTER LEG, 29 5/8 C/C 1
526-510-031 WELDMENT, UPPER INNER LEG, 29 5/8 C/C 1
626-510-034 WELDMENT, UPPER OUTER LEG 1
701-115-001 WASHER, THRUST BEARING, 1 1/8 ID 12
801-527-001 ROLLER W/ BUSHING 4
968021 EXTERNAL RETAINING RING, PHOSPHATE FINISH, 1-1/8" 12
10 26-112-001 PIN, HINGE 4
11 33454 NARROW MACHINERY BUSHING, PLAIN FINISH, 1 3/4" X 18 GA 8
12 26-112-005 PIN, PIVOT, TORSION END 2
13 01-112-008 PIN, SCISSOR PIVOT 2
14 26-112-006 PIN, DBL SCISSOR PIVOT 4
15 01-115-002 WASHER, THRUST BEARING 8
16 36209 1/2 - 13 HEX JAM NUT PLAIN 1
17 01-118-001 BOLT, CYLINDER RETAINING 1
18 26333 SHOULDER SCREW 0.375x1.5" LG 4
19 26335 SHOULDER SCREW 0.375x2" LG 2
20 33004 FLAT WASHER, USS, ZINC PLATED, Ø1/4" 6
21 37021 NYLON INSERT LOCK NUT, GRADE 2, ZINC FINISH, 5/16"-18 6
22 24-612-003 WELDMENT, CYLINDER PIN 1
23 04-130-001-001 PIN RETAINER 1
24 09-112-011 PIN, CYLINDER, BOX DUMPER 1
25 32415 Ø5/16 - 18 x 1/2 HWH THREAD CUTTING SCREW, TYPE F, ZINC 1
26 64134 SPRING PIN 2
27 99-115-001 WASHER, THRUST 4
28 99-021-901-001 CYLINDER, HYDRAULIC, Ø3" x 10" RAM STYLE, MACHINED END 1
29 26-513-004 WELDMENT, DECK 1
30 01-515-026
SUB-ASSEMBLY, TOE GUARD, 48" X 64", INCLUDES HARDWARE &
SWITCHES
1

TABLE OF CONTENTS Rev. 2/2/2022 EHLTD MANUAL
TABLE OF CONTENTS Copyright 2021 Vestil Manufacturing Corp. Page 12 of 28
EXPLODED VIEW: EHLTD-4864-2-84 (26-006-071-002)

TABLE OF CONTENTS Rev. 2/2/2022 EHLTD MANUAL
TABLE OF CONTENTS Copyright 2021 Vestil Manufacturing Corp. Page 13 of 28
BILL OF MATERIALS: EHLTD-4864-2-84 (26-006-071-002)
ITEM NO PART NO DESCRIPTION QTY.
126-002-070 FINAL ASSEMBLY W/O POWER UNIT 1
226-514-002 WELDMENT, FRAME ASSEMBLY 1
326-510-028 WELDMENT, LOWER INNER LEGS, 29 5/8 C/C 1
426-510-030 WELDMENT, LOWER OUTER LEG, 29 5/8 C/C 1
526-510-032 WELDMENT, UPPER INNER LEG, 29 5/8 C/C 1
626-510-034 WELDMENT, UPPER OUTER LEG 1
701-115-001 WASHER, THRUST BEARING, 1 1/8 ID 12
801-527-001 ROLLER W/ BUSHING 4
968021 EXTERNAL RETAINING RING, PHOSPHATE FINISH, 1-1/8" 12
10 26-112-001 PIN, HINGE 4
11 33454 NARROW MACHINERY BUSHING, PLAIN FINISH, 1 3/4" X 18 GA 8
12 26-112-005 PIN, PIVOT, TORSION END 2
13 01-112-008 PIN, SCISSOR PIVOT 2
14 26-112-006 PIN, DBL SCISSOR PIVOT 4
15 01-115-002 WASHER, THRUST BEARING 8
16 36209 1/2 - 13 HEX JAM NUT PLAIN 2
17 01-118-001 BOLT, CYLINDER RETAINING 2
18 26333 SHOULDER SCREW 0.375x1.5" LG 4
19 26335 SHOULDER SCREW 0.375x2" LG 2
20 33004 FLAT WASHER, USS, ZINC PLATED, Ø1/4" 6
21 37021 NYLON INSERT LOCK NUT, GRADE 2, ZINC FINISH, 5/16"-18 6
22 24-612-003 WELDMENT, CYLINDER PIN 2
23 32415 Ø5/16 - 18 x 1/2 HWH THREAD CUTTING SCREW, TYPE F, ZINC 2
24 64134 SPRING PIN 2
25 99-115-001 WASHER, THRUST 4
26 99-521-901-001
CYLINDER, HYDRAULIC, Ø3" x 10" RAM STYLE, MACHINED END, 2GPM
VF
2
27 26-513-004 WELDMENT, DECK 1
28 01-515-026
SUB-ASSEMBLY, TOE GUARD, 48" X 64", INCLUDES HARDWARE &
SWITCHES
1

TABLE OF CONTENTS Rev. 2/2/2022 EHLTD MANUAL
TABLE OF CONTENTS Copyright 2021 Vestil Manufacturing Corp. Page 14 of 28
EXPLODED VIEW: EHLTD-4864-3/4/5-84 (26-006-081-002)

TABLE OF CONTENTS Rev. 2/2/2022 EHLTD MANUAL
TABLE OF CONTENTS Copyright 2021 Vestil Manufacturing Corp. Page 15 of 28
BILL OF MATERIALS: EHLTD-4864-3/4/5-84 (26-006-081-002)
ITEM NO PART NO DESCRIPTION QTY.
126-002-080 FINAL ASSEMBLY W/O POWER UNIT 1
226-514-002 WELDMENT, FRAME ASSEMBLY 1
326-510-029 WELDMENT, LOWER INNER LEGS, 29 5/8 C/C 1
426-510-030 WELDMENT, LOWER OUTER LEG, 29 5/8 C/C 1
526-510-033 WELDMENT, UPPER INNER LEG, 29 5/8 C/C 1
626-510-034 WELDMENT, UPPER OUTER LEG 1
701-115-001 WASHER, THRUST BEARING, 1 1/8 ID 12
801-527-001 ROLLER W/ BUSHING 4
968021 EXTERNAL RETAINING RING, PHOSPHATE FINISH, 1-1/8" 12
10 26-112-001 PIN, HINGE 4
11 33454 NARROW MACHINERY BUSHING, PLAIN FINISH, 1 3/4" X 18 GA 8
12 26-112-005 PIN, PIVOT, TORSION END 2
13 01-112-008 PIN, SCISSOR PIVOT 2
14 26-112-006 PIN, DBL SCISSOR PIVOT 4
15 01-115-002 WASHER, THRUST BEARING 8
16 36209 1/2 - 13 HEX JAM NUT PLAIN 3
17 01-118-001 BOLT, CYLINDER RETAINING 3
18 26333 SHOULDER SCREW 0.375x1.5" LG 4
19 26335 SHOULDER SCREW 0.375x2" LG 2
20 33004 FLAT WASHER, USS, ZINC PLATED, Ø1/4" 6
21 37021 NYLON INSERT LOCK NUT, GRADE 2, ZINC FINISH, 5/16"-18 6
22 64134 SPRING PIN 2
23 99-115-001 WASHER, THRUST 4
24 99-521-901-001
CYLINDER, HYDRAULIC, Ø3" x 10" RAM STYLE, MACHINED END, 2GPM
VELOCITY FUSE
3
25 24-112-003 PIN, CYLINDER PIVOT 1
26 26-513-004 WELDMENT, DECK 1
27 01-515-026
SUB-ASSEMBLY, TOE GUARD, 48" X 64", INCLUDES HARDWARE &
SWITCHES
1

TABLE OF CONTENTS Rev. 2/2/2022 EHLTD MANUAL
TABLE OF CONTENTS Copyright 2021 Vestil Manufacturing Corp. Page 16 of 28
ELECTRIC CIRCUIT DIAGRAMS
Care should be taken to identify all potential hazards and comply with applicable safety
procedures before beginning work. Ensure that all system pressure and electrical power
have been removed before attempting to work on the electrical or hydraulic systems.
Follow all applicable lockout/tagout procedures.
The load must be removed, and the platform either positively and adequately supported
or fully lowered, before any work is performed on the lift table.
Only qualified individuals trained to understand mechanical devices and their associated electrical and
hydraulic cir
cuits, as well as the hazards associated with them, should attempt troubleshooting and repair
of this equipment.
115 VAC, Single-Phase Electric Circuit Diagram (24124012 Rev. A)
Note: Overcurrent & short circuit protection and disconnect must be provided by end user.

TABLE OF CONTENTS Rev. 2/2/2022 EHLTD MANUAL
TABLE OF CONTENTS Copyright 2021 Vestil Manufacturing Corp. Page 17 of 28
208-230 VAC, Single-Phase Electric Circuit Diagram (24124013 Rev. A)
Note: Overcurrent & short circuit protection and disconnect must be provided by end user.
3-Phase Electric Circuit Diagram (24124014 Rev. A)
Note: Overcurrent & short circuit protection and disconnect must be provided by end user.

TABLE OF CONTENTS Rev. 2/2/2022 EHLTD MANUAL
TABLE OF CONTENTS Copyright 2021 Vestil Manufacturing Corp. Page 18 of 28
Motor Lead Connections (99124021).
Applicable to all all .5 HP, .75 HP, and 3 HP single-phase motors, and for all 2 HP, 5.5 HP, and 6.5 HP three-
phase motors.
* The two thermostat leads go to (1) the grounded side of the transformer secondary, and; (2) the motor
relay coil. Polarity across the thermostat leads is not important.
When changing the motor voltage configuration, you must also change the configuration
of the control transformer to match the motor voltage.
Control Voltage Transformer (01129001 Rev. G).

TABLE OF CONTENTS Rev. 2/2/2022 EHLTD MANUAL
TABLE OF CONTENTS Copyright 2021 Vestil Manufacturing Corp. Page 19 of 28
Power Unit Subassembly.
Power Unit:2 HP, 3 PH (99-137-018-004).
Representative diagram. Contact the factory for replacement parts for your specific model. ALWAYS have
the product serial number or model number on hand
when calling the factory.
ITEM
PART NO.
DESCRIPTION
QTY
1 99-135-005
MOTOR, 2 HP, 3PH,
1725 RPM, 56F, 208-
230/460V, 50/60HZ
1
2 01-143-
908-002
PUMP, HYDRAULIC
GEAR, .153 Disp, 2.7
cc/r
1
3
23305
SHCS, 3/8 - 16 x 1 LG.
2
4 33688
LOCK WASHER, HIGH
COLLAR, 3/8
2
5 96056
WASHER, FLAT, 3/8"
NOMINAL, .406" I.D.,
YELLOW ZINC SAE
2
6 99-034-037
ACCESSORIES,
ELECTRICAL, ROMEX
.375"
1
Manifold Assembly (01-627-015 Rev. A).
ITEM
PART NO.
DESCRIPTION
QTY
1
01-127-010
MANIFOLD, L-H-L
1
2 99-034-008
COIL WITH DIN
CONNECTOR
1
3 99-144-008
O-RING, MANIFOLD,
1/2" OD
1
4 99-144-009
O-RING, MANIFOLD,
3/4" OD
1
5 99-153-006
VALVE, PRESSURE
RELIEF, 210 BAR
1
6 99-153-011
CHECK VALVE, SIZE
08, NOSE-IN/SIDE-OUT
1
7 99-153-015
VALVE SOLENOID,
STANDARD, w/o COIL
1
8 99-153-040
FLOW CONTROL,
PRES. COMP., 2.0
GAL.
1

TABLE OF CONTENTS Rev. 2/2/2022 EHLTD MANUAL
TABLE OF CONTENTS Copyright 2021 Vestil Manufacturing Corp. Page 20 of 28
Hydraulic Schematic (01-125-008).
ITEM
PART NO.
DESCRIPTION
QTY
1
01-127-010
MANIFOLD, LHL
1
2 99-153-011
CHECK VALVE, SIZE
08, NOSE-IN/SIDE-OUT
1
3
0.5 GPM
99-153-049
FLOW CONTROL,
PRES. COMP. 1
1.0 GPM
99-153-038
1.5 GPM
99-153-039
2.0 GPM
99-153-040
4 99-153-006
VALVE, PRESSURE
RELIEF, 210 BAR
1
5 99-153-015
VALVE SOLENOID,
STANDARD, w/o COIL
1
INSTALLATING THE TABLE
Read the installation instructions in their entirety before installing the scissor lift table.
Consult the factory in the event of questions or problems at the time of installation.
Modifications or additions to the lift table, without prior authorization by the manufacturer, may void the
warranty. See ANSI standard MH29.1-2003, Safety Requirements for Industrial Scissor Lifts, Section 12.6.
Attaching ancillary equipment to the platform will lower its load capacity.
The installation shall comply with all applicable regulations for its location and use.
The end user is responsible for verifying that this lift table and its installation are suitable for its environment
and application.
This lift table shall be installed only by qualified and trained personnel with access to appropriate
equipment. Electrical connections shall be performed by a qualified electrician.
Before You Begin.
The Electric Hydraulic Scissors Lift Table must be anchored to a smooth, level, and adequately strong
concrete surface. If the lift table will be installed in a pit, first determine where and how the electrical
and/or hydraulic connections will be made when the lift table is in place.
Tools And Supplies.
The following tools and supplies may be needed to install your Electric Hydraulic Scissor Lift Table. These
items are not supplied with the product.
•A fork truck or hoist capable of unloading the left table and setting it in place.
•A smooth, level concrete surface on which to mount the lift table.
•Four concrete anchors. The customer is responsible for selecting anchors appropriate for the EHLTD
model and concrete floor conditions. DO NOT operate an unsecured lift table.
•A power supply and electrical disconnect matching the motor’s voltage and current requirements. Refer
to the lift table’s data plate, labels on the control enclosure, and the electrical diagrams in this manual for
more information. The end-user is responsible for supplying the required ground-fault and short-circuit
protection on the supply. Motor overload protection is provided by a thermostat built into the motor.