Vestil FORK-P User manual

Rev. 4/6/2018 FORK-P MANUAL
Copyright 2018 Vestil Manufacturing Corp. Page 1 of 4
FORK-P Instruction Manual
Receiving instructions:
After delivery, IMMEDIATELY remove the packaging from the product in a manner that preserves the
packaging; then inspect the product closely to determine whether it sustained damage during transport. If
damage is discovered during the inspection, immediately record a complete description of the damage on
the bill of lading. If the product is undamaged, discard the packaging.
NOTE:
The end-user is solely responsible for complying with laws, regulations, codes, and non-voluntary
standards enforced in the location where the product is used.
Vestil Manufacturing Corp.
2999 North Wayne Street, P.O. Box 507, Angola, IN 46703
Telephone: [phone] -or- Toll Free [phone]
Fax: [phone]
Web
:
www.vestilmfg.com
e
-
mail:
info
@vestil.com
Table of Contents
Signal Words………………………………………………………………………………………………………….2
Hazards of Improper Use……………………………………………………………...………………………...….2
FORK-P Exploded View………………………...………..……………………………….………………………...3
Labeling Diagram……………………………………………………………………………………………………. 3
Using the Lifter………………………………………………………………………………………………………. 3
Inspections & Maintenance………………………………………………………………………………………… 3
Limited Warranty…………………………………………………………………………………………………….. 4

Rev. 4/6/2018 FORK-P MANUAL
Copyright 2018 Vestil Manufacturing Corp. Page 2 of 4
SIGNAL WORDS
This manual uses SIGNAL WORDS to indicate the likelihood of personal injuries, as well as the
probable seriousness of those injuries, if the product is misused in the ways described. Other signal
words call attention to uses of the product likely cause property damage. The signal words used appear
below along with the meaning of each word.
Identifies a hazardous situation which, if not avoided, WILL result in DEATH or
SERIOUS INJURY. Use of this signal word is limited to the most extreme situations.
Identifies a hazardous situation which, if not avoided, COULD result in DEATH or
SERIOUS INJURY.
Indicates a hazardous situation which, if not avoided, COULD result in MINOR or
MODERATE injury.
Identifies practices likely to result in product/property damage, such as operation that
might damage the product.
HAZARDS OF IMPROPER USE
We strive to identify all foreseeable hazards associated with the use of our products. However, no
manual can address every risk. The most effective means for avoiding injury is to exercise sound
judgment whenever using this cart.
Improper or careless operation might result in serious personal injuries.
DO NOT exceed the 400 lb. (181.8 kg) capacity. Capacity is the maximum load the product can lift.
The lifting equipment (crane, hoist, trolley) must have AT LEAST the same capacity as this fork lifter.).
DO NOT attempt to lift any load whose weight exceeds the maximum rated load of the lifting component
(crane, trolley, hoist, FORK-P, etc.) with the smallest capacity. For example, if the crane, hoist and
FORK-P each have capacities of 400 pounds, but the trolley has a capacity of 100 pounds, the net
weight applied to the trolley must not exceed 100 pounds.
DO NOT use the fork lifter if any part of it is severely worn or damaged.
ALWAYS inspect the unit before each use according to the inspection procedures described in the
most recent revision of ASME standard B30.20.
Review the safety messages included in the manuals for your crane, trolley, hoist, and any other
device used in conjunction with the fork lifter.
Be certain that the fork moved with this device is properly attached to the forklift carriage before
disconnecting the fork from the lifter.
ALWAYS attach the lifter to a safety hook (e.g. a hoist hook that has a self-closing latch across the
throat opening of the hook) or to a connection that includes safety mechanisms to prevent accidental or
unintended detachment. DO NOT attach the lifter to a safety hook that does not function properly.
Attach the hoist hook to the appropriate lifting eye. The fork blade should be close to horizontal or tip
slightly towards the toe when the fork is suspended. (See “Using the Lifter” on p. 3).
Always test the connection between the lifter and the fork before raising the fork. Tighten both
knobs/tine locks against the blade of the fork. Confirm that the fork cannot slide out of the fork channel.
Only use the lifter to move a fork if the connection is secure.
DO NOT raise the loaded lifter over your feet or any other part of your body. Every person not involved
with lifting the fork should remain outside the lifting area for the duration of the process.
Avoid load swing. Before raising the fork, the hoist chain should be vertical, i.e. not angled. Slowly
raise the fork. Maintain control as the fork and lifter are raised.
Proper use, maintenance, and storage are essential for this product to function properly.
oAlways use this product in accordance with the instructions in this manual and consistent with any
training relevant to machines, devices, etc. used in conjunction with this product.
oKeep the product clean & dry.

Rev. 4/6/2018 FORK-P MANUAL
Copyright 2018 Vestil Manufacturing Corp. Page 3 of 4
FORK-P EXPLODED VIEW LABELING DIAGRAM
USING THE LIFTER
To properly use the fork lifter, apply the following steps:
1. Insert the toe of the fork into the right side of the lifter.
2. Slide the lifter over the blade of the fork until the fork shank contacts the shank stop.
3. Tighten the knobs against the top of the fork.
4. Attach the hoist hook to the appropriate lifting eye.
5. Fine tune the position of the hoist so that the hoist chain/rope is vertical (not angled).
6. Lift the fork just a few inches from the ground.
a. If the fork tilts toward the heel, lower the fork until it rests securely on the ground.
b. Move the hoist hook to a lifting eye closer to the shank stop.
c. Repeat step 5 until the fork balances (blade remains level when lifted) or tilts slightly toward the toe.
7. Slowly elevate the fork while grasping the lifter to maintain stability. Keep the rest of your body away from the
fork and lifter. In particular, be sure that your feet are never under the fork while it is elevated.
8. Attach the fork to the carriage of you forklift.
INSPECTIONS & MAINTENANCE
Before putting the lifter into service for the first time, make a written record that describes its appearance and
operation. Measure the lifting eyes and record their diameters. Describe how easily the knobs wind into their
receivers. Measure the fork channel openings and record the figures. Take photos of the unit from various vantage
points and add them to the record. The record establishes normal condition of the fork lifter. During future
inspections, compare your findings to the record to determine whether the lifter is in normal condition.
Before each use, examine the following features. Do not use the lifter unless it is in normal condition.
a. Welds: confirm that all welds are intact.
b. Fork channel: the channel should be square a rigid, free of significant rust/corrosion, and not significantly worn.
Use a steel bristle brush to remove rust. Clean the affected areas and apply touchup paint.
c. Lifting eyes: confirm that the lifting eyes are not stretched, broken, etc.
d. Knobs and receivers: make sure that both knobs are undamaged and thread smoothly into their receivers.
Tighten knobs
against top of fork
Toe of fork
Fork
shank Carriage
hook
Shank
stop
Lifting eyes
B
A
A: Label 675 (on side of
fork channel)
B: Label 1000 (on opposite
side of fork channel)
K
nob receiver

Rev. 4/6/2018 FORK-P MANUAL
Copyright 2018 Vestil Manufacturing Corp. Page 4 of 4
LIMITED WARRANTY
Vestil Manufacturing Corporation (“Vestil”) warrants this product to be free of defects in material and workmanship
during the warranty period. Our warranty obligation is to provide a replacement for a defective original part if the part is
covered by the warranty, after we receive a proper request from the warrantee (you) for warranty service.
Who may request service?
Only a warrantee may request service. You are a warrantee if you purchased the product from Vestil or from an
authorized distributor AND Vestil has been fully paid.
What is an “original part”?
An original part is a part used to make the product as shipped to the warrantee.
What is a “proper request”?
A request for warranty service is proper if Vestil receives: 1) a photocopy of the Customer Invoice that displays the
shipping date; AND 2) a written request for warranty service including your name and phone number. Send requests
by any of the following methods:
Mail Fax Email
Vestil Manufacturing Corporation [phone] [email protected]
2999 North Wayne Street, PO Box 507 Phone
Angola, IN 46703 [phone]
In the written request, list the parts believed to be defective and include the address where replacements should be
delivered.
What is covered under the warranty?
After Vestil receives your request for warranty service, an authorized representative will contact you to determine
whether your claim is covered by the warranty. Before providing warranty service, Vestil may require you to send the
entire product, or just the defective part or parts, to its facility in Angola, IN. The warranty covers defects in the following
original dynamic components: motors, hydraulic pumps, electronic controllers, switches and cylinders. It also covers
defects in original parts that wear under normal usage conditions (“wearing parts”): bearings, hoses, wheels, seals,
brushes, batteries, and the battery charger.
How long is the warranty period?
The warranty period for original dynamic components is 30 days. For wearing parts, the warranty period is 30 days.
Both warranty periods begin on the date Vestil ships the product to the Warrantee. If the product was purchased from
an authorized distributor, the periods begin when the distributor ships the product. Vestil may, at its sole discretion,
extend a warranty period for products shipped from authorized distributors by up to 30 days to account for shipping
time.
If a defective part is covered by the warranty, what will Vestil do to correct the problem?
Vestil will provide an appropriate replacement for any covered part. An authorized representative of Vestil will contact
you to discuss your claim.
What is not covered by the warranty?
The Warrantee (you) are responsible for paying labor costs and freight costs to return the product to Vestil for warranty
service.
Events that automatically void the Limited Warranty.
Misuse;
Negligent assembly, installation, operation or repair;
Installation/use in corrosive environments;
Inadequate or improper maintenance;
Damage sustained during shipping;
Collisions or other accidents that damage to the product;
Unauthorized modifications: Do not modify the product IN ANY WAY without first receiving written authorization
from Vestil.
Do any other warranties apply to the product?
Vestil Manufacturing Corp. makes no other express warranties. All implied warranties are disclaimed to the extent
allowed by law. Any implied warranty not disclaimed is limited in scope to the terms of this Limited Warranty.