VICI DBS NM PLUS User manual

1
NM & PG PLUS FID STATIONS
USER MANUAL
Version 1.03.0000
www.vicidbs.com
TECH SUPPORT
Europe, Asia, Africa, Australia & New Zealand:
[e-mail]
USA, Canada, Central & South America:
[e-mail]
Italy
[e-mail]
VICI AG INTERNATIONAL
Parkstrasse 2
CH-6214 Schenkon
Switzerland
tel: [phone]
fax: [phone]
web: www.vicidbs.com
APPLICABLE MODELS
This manual is applicable to the following models:
• NM Plus 100 FID Station
• NM Plus 300 FID Station
• NM Plus 600 FID Station
• NM Plus 1000 FID Station
• PG Plus 100 FID Station
• PG Plus 250 FID Station
Version 1.03.0000

1
NM & PG PLUS FID STATIONS
USER MANUAL
Version 1.03.0000
www.vicidbs.com
TABLE OF CONTENTS
1. VERSION HISTORY................................................................................................................................ 2
2. INTRODUCTION.................................................................................................................................... 3
2.1 SYMBOL DEFINITIONS ........................................................................................................................3
3. SAFETY.................................................................................................................................................. 4
3.1. PERSONAL SAFETY INSTRUCTIONS..................................................................................................4
3.2. INSTRUMENT SAFETY INSTRUCTIONS.............................................................................................4
4. SPECIFICATIONS................................................................................................................................... 5
4.1. MOST COMMON OPTION.................................................................................................................6
4.1.1. Remote Connections...................................................................................................................6
4.1.2. Cascading ...................................................................................................................................6
5. PRESENTATION OF THE DEVICE.......................................................................................................... 8
5.1. FRONT VIEW .......................................................................................................................................8
5.2. BACK VIEW .........................................................................................................................................8
5.3. INTERNAL VIEW .................................................................................................................................9
5.4. SCHEMATICS ....................................................................................................................................10
5.4.1. Fluidics .....................................................................................................................................10
5.4.2. Electronics ................................................................................................................................12
5.5. DIMENSIONS .................................................................................................................................... 14
5.6. WEIGHT ............................................................................................................................................15
5.7. TRANSPORT AND STORAGE ...........................................................................................................15
5.8. FUSES AND VOLTAGE SETTINGS .................................................................................................... 16
6. INSTALLATION AND INITIAL START-UP ............................................................................................. 17
6.1. RECEIVING THE GENERATOR .......................................................................................................... 17
6.2. INSTALLING THE GENERATOR ........................................................................................................ 17
6.3. GAS CONNECTIONS .......................................................................................................................18
6.4. FILLING THE WATER TANK .............................................................................................................. 19
6.5. INSTALLING THE DEIONIZER BAG ..................................................................................................20
6.6. STARTING THE HYDROGEN GENERATOR......................................................................................21
6.7. TURNING OFF THE GENERATOR ....................................................................................................22
6.8. STARTING THE ZERO AIR GENERATOR ..........................................................................................22
8. OPERATION - HYDROGEN PART ........................................................................................................ 24
8.1. LCD DISPLAY .....................................................................................................................................24
8.1.1. Layout of the Display................................................................................................................24
8.1.2. First Row - Pressure Information...............................................................................................24
8.1.3. Second Row - Pressure Information .........................................................................................24
8.1.4. Third Row - Hydrogen Flow .....................................................................................................25
8.1.5. Fourth Row - Water Quality......................................................................................................25
8.1.6. Start/Stop - Reset Button .........................................................................................................25
8.1.7. Exit - Menu Button ...................................................................................................................25
8.2. MENU STRUCTURE...........................................................................................................................26
8.3. CONFIGURE PARAMETERS..............................................................................................................27

2
NM & PG PLUS FID STATIONS
USER MANUAL
Version 1.03.0000
www.vicidbs.com
1. VERSION HISTORY
VERSION DATE COMMENT/CHANGE
1.00.0100 01/18/2017 Layout and initial release, VICI DBS
1.01.0000 10/24/2017 Update, VICI DBS
1.02.0000 01/09/2020 New layout, images and graphics, VICI Gig Harbor Group
1.03.0000 03/01/2021` Update, VICI DBS
8.4. DIAGNOSTIC DISPLAY .....................................................................................................................28
8.5. SPECIAL FUNCTIONS.......................................................................................................................29
9. OPERATION - ZERO AIR PART ............................................................................................................ 29
9.1. CONNECT POWER AND START UNIT.............................................................................................29
9.2. WARMING UP...................................................................................................................................29
9.3. SHUTDOWN PROCEDURE...............................................................................................................30
10. ERROR LIST - TROUBLESHOOTING .................................................................................................. 30
10.1. HYDROGEN PART ...........................................................................................................................30
10.2. ZERO AIR PART ...............................................................................................................................31
10.2.1. Front Panel LED .....................................................................................................................31
10.2.2. Error Codes on Mainboard.....................................................................................................32
11. MAINTENANCE................................................................................................................................. 33
11.1. ROUTINE MAINTENANCE - HYDROGEN PART..............................................................................33
11.2. ROUTINE MAINTENANCE - ZERO AIR PART..................................................................................33
11.2.1. Maintenance Kits....................................................................................................................34
11.2.2. Annual Maintenance Kit .........................................................................................................34
11.2.3. Three-Year Catalyst Replacement Kit .....................................................................................34
11.3. ANNUAL PRE-FILTER ELEMENT REPLACEMENT............................................................................34
11.4. THREE-YEAR CATALYST CHAMBER REPLACEMENT......................................................................35
12. RETURNING THE UNIT...................................................................................................................... 36
13. SPARE PARTS LIST............................................................................................................................. 37
13.1. Hydrogen Part..................................................................................................................................37
13.2. Zero Air Part ....................................................................................................................................40

3
NM & PG PLUS FID STATIONS
USER MANUAL
Version 1.03.0000
www.vicidbs.com
2. INTRODUCTION
The NM & PG Plus FID Stations are 2 in 1 generators of hydrogen and zero air. The ows are optimized to
guarantee a correct functioning of the FID in your GC-MS system. The NM & PG Plus FID Stations need only
a small amount of space on your lab bench due to its space-saving design.
2.1. SYMBOL DEFINITIONS
SYMBOL DESCRIPTION
General warning. Caution is necessary when operating the device or control
close to where the symbol is placed, or to indicate that the current situation
needs operator awareness or operator action in order to avoid undesirable
consequences.
The manual must be consulted in all cases where this symbol is marked on
the device.
Risk of asphyxia. Caution is necessary when operating the device in a not
sufciently ventilated area.
Oxidant material. Caution is necessary due to the presence of oxidant material.
WEEE symbol. When discard this product, it must be sent to separate collection
facilities for recovery and recycling.
Fuse. Notify replaceable fuse place.
OR
OR
OR

4
NM & PG PLUS FID STATIONS
USER MANUAL
Version 1.03.0000
www.vicidbs.com
3. SAFETY
3.1. PERSONAL SAFETY INSTRUCTIONS
Read all instructions and warnings. Failure to do so could induce electrical shock, re and/or serious injury to
the user.
• For indoor use only.
• Never operate the unit at temperatures below 0°C or 32°F. This will cause irreversible
damage to the electrolysis cell.
• Only use pure (deionized) water (see Filling the Water Tank)
• Only operate the unit in a room with sufcient ventilation (see “Installing the
Generator”).
• Only the parts described in the “Spare parts list” can be replaced by the user.
• Do not use the unit if a fault is known.
3.2. INSTRUMENT SAFETY INSTRUCTIONS
The NM and PG Plus FID Stations are designed to produce hydrogen for laboratory and industrial
applications. The unit must only be operated for this purpose, according to the specications and instructions
provided in this manual. The following warnings must be observed at all times. Critical damages on the device
could occur if following warnings are neglected.
• Usual precautions for any hydrogen supply should be taken when using this generator.
• DO NOT use in sealed or unventilated rooms.
• DO NOT use in close proximity to open ames or other sources of ignition.
• Keep the main power supply cable away from hot sources or oil. Damaged or entangled
power supply cables could increase the risk of electrical shock.
• In normal usage, unplug the main power supply cable only when the unit is turned off.
• The main power supply connector must be easily disconnected in case of emergency. It
must be easily accessible at all times.
• DO NOT open and attempt to repair the unit by un-trained individuals.
• DO NOT replace parts with ones not approved by VICI DBS.
• Always unplug the unit from the main power supply before accessing the internal
components for replacement.
• If the unit is used in a way not specied by VICI DBS, the instrument warranty could be
canceled.

5
NM & PG PLUS FID STATIONS
USER MANUAL
Version 1.03.0000
www.vicidbs.com
4. SPECIFICATIONS
GENERAL
Operating temperature ºC (ºF) 15 to 35 (59 to 95)
Operating relative humidity 0 to 80%, non-condensing
Dimension mm (in) 690W x 150H x 680D (27W x 6H x 26.7D)
Electrical supply 110-120V 60Hz / 220-240V 50Hz
Electrical protection Transient over-voltage until over-voltage category II (Accept transient
over-voltage occurring on the network)
General earth connection is done by the main power supply cable.
Fuse F2 : 5x20mm, 4.0 or 6.3 A T (see “Fuses and Voltage Setting”)
Microprocessor controlled Graphic display - Touch Screen, 128 x 64 pixels
Pollution degree 2
IP protection degree IP20
Atmospheric pressure From 850 to 1150 hPa
External vibrations Inferior to 0.05g / 25Hz
Working instruments position Horizontal ONLY
HYDROGEN COMPONENT
TYPE & PURITY FLOW RATE AT STP CC/MIN POWER CONSUMPTION
Hydrogen ow rate - PG models
Purity +99.9996%
HC free
100, 250 65 to 115 W
Hydrogen ow rate - NM models
Purity +99.99996%
HC free
100, 300, 600, 1000, 1350 90 to 400 W
Max outlet pressure barg (psig) 11 (160)
AIR COMPONENT
TYPE & PURITY FLOW RATE AT STP CC/MIN POWER CONSUMPTION
Zero air purity ow
HC free
1800, 5000 200 to 500 W
Max outlet pressure barg (psig) 5 (72.5) to ±0.1 (±0.5)
STP: Standard temperature and pressure (20°C, 1 barg)
Any changes or modications to this equipment not expressly approved by the manufacturer may void
the user’s authority to operate the equipment.

6
NM & PG PLUS FID STATIONS
USER MANUAL
Version 1.03.0000
www.vicidbs.com
4.1. COMMON OPTIONS
4.1.1. Remote Connections
Requires the I/O board option.
The hydrogen generators are tted with an optional remote control feature, which allows the user to check
the status of the machine from a remote position, and to start/stop the production of hydrogen. The contacts
used in the remote control are potentially free relay contacts. The contacts can be congured via software as
normally-open or normally-closed (see the Conguration section). The maximum voltage and current ratings
for the contacts are 1A / 48V. The pin conguration of the remote connector is shown in the table below.
Remote connector pin conguration:
PIN DESCRIPTION
1+2 Start (12-30 VDC polarity not important)
3+4 Standby
5+6 Reaching external pressure
09+10 Low water level
11+12 Bad water
13+14 Change water
4.1.2. Cascading
Requires the I/O board option.
The RS-485 interface allows up to 10 generators to be operated in parallel mode. The generators are
connected with an external non-return valve to a gas line. The pressure must be controlled with an external
pressure regulator. The outlet pressure is xed to 10.3 bars. This mode allows up to 10 generators in a
cascading group.
How does cascading work:
The communication of the generators is done via the RS-485 interface. For a correct communication each
generator needs a unique ID number. Each generator must know how many generators are connected in the
cascading group.
As soon as the generators are powered up, one generator becomes the master, and controls the others
(slaves). If there is a problem with the master, one of the slave generators will become the master. Every
generator can be forced to be the master, by entering into the menu you will see the function “force to
master”, just select this function and acknowledge. When a generator is the master, you can see the letter
“M” in the menu button, while the slaves show the letter “S”.

7
NM & PG PLUS FID STATIONS
USER MANUAL
Version 1.03.0000
www.vicidbs.com
GAS LINE
PRESSURE CONTROLLER
NON RETURN VALVE NON RETURN VALVES
H2 OUT
GENERATOR 1
H2 OUT
GENERATOR 2
H2 OUT
GENERATOR 3
CONFIGURATION
Cascading Mode: YES
N. Gen H2 in Cascading: 3
ID Number: 1
RS-485 Port 1 RS-485 Port 2
CONFIGURATION
Cascading Mode: YES
N. Gen H2 in Cascading: 3
ID Number: 2
RS-485 Port 1 RS-485 Port 2
CONFIGURATION
Cascading Mode: YES
N. Gen H2 in Cascading: 3
ID Number: 3
RS-485 Port 1 RS-485 Port 2
The cascading function will only work properly if the gas outlets on all the generators are
connected to the same gas line.

8
NM & PG PLUS FID STATIONS
USER MANUAL
Version 1.03.0000
www.vicidbs.com
5. PRESENTATION OF THE DEVICE
5.1. FRONT VIEW
Touch display to control and
manage the generator
Zero air manometer
Water drain
Power on/off for
H2
Status LED for zero
air generator
Zero air pressure regulator
USB port
Power on/off for
zero air
5.2. Back View
Outlet H2 Relief Valve
110/230 V Inlet CEI C14
Fuse Holder 3
I/O Board Option
Hydrogen Outlet
Volt Selector with F2 Fuse Holder
Zero Air Inlet
Water Inlet
Remove Plug Before Use
Set the Correct Fuses
Zero Air Outlet
Outlet Vent O2 G 1/8” Female
Remove Plug Before Use

9
NM & PG PLUS FID STATIONS
USER MANUAL
Version 1.03.0000
www.vicidbs.com
5.3. INTERNAL VIEW
Perma Pure
H2 Motherboard
GLS
Circuit Pump
Air Motherboard
Cooling Coil
Zero Air Catalyst
Cell
Power Supply
Water Tank
Dryer (NM version only)
Internal Water Tanks

10
NM & PG PLUS FID STATIONS
USER MANUAL
Version 1.03.0000
www.vicidbs.com
5.4. SCHEMATICS
5.4.1. Fluidics
The hydrogen generator produces pure hydrogen (and oxygen as a by-product) through the electrolysis of
water. The key element of the generator is an electrochemical cell assembly which contains a solid polymer
electrolyte. No free acids or bases are used. Deionized or pure distilled water is the only liquid which will be in
contact with the cell. Since water is consumed it must be relled from time to time as required. The generated
hydrogen gas is accumulated in the hydrogen/water separator and the desiccant housing. The internal
pressure is controlled by a pressure transducer. The outlet pressure is controlled by a proportional valve. The
hydrogen is dried by passing through the automatic dryer. The hydrogen then passes through the outlet port
at the rear.
Air from the external compressed air source goes rst trough an external dust lter. Then it will pass through a
catalytic oven that will remove the CO and CH4. After cooling, the air is ready.
System:
Schematic no:
Date:
Created:
Checked:
Released:
THIS DOCUMENT AND THE INFORMATION WHICH
IT CONTAINS SHALL NOT BE USED, EXPLOITED
OR SOLD, AND SHALL NOT BE REVEALED OR
DISCLOSED TO OTHERS WITHOUT THE EXPRESS
WRITTEN PERMISSION OF VICI. THIS DOCUMENT
SHALL REMAIN THE PROPERTY OF VICI AND
SHALL BE RETURNED UPON DEMAND.
R
Rev.:
Sheet:
By:
Description:
ECN no:
PG Plus FID-Station
water and hydrogen flow diagram 06.10.2020
06.10.2020
SBU
SB
1
1/1
PG Plus Fluidics - Zero Air Part
PG Plus Fluidics - Hydrogen Part

11
NM & PG PLUS FID STATIONS
USER MANUAL
Version 1.03.0000
www.vicidbs.com
System:
Schematic no:
Date:
Created:
Checked:
Released:
THIS DOCUMENT AND THE INFORMATION WHICH
IT CONTAINS SHALL NOT BE USED, EXPLOITED
OR SOLD, AND SHALL NOT BE REVEALED OR
DISCLOSED TO OTHERS WITHOUT THE EXPRESS
WRITTEN PERMISSION OF VICI. THIS DOCUMENT
SHALL REMAIN THE PROPERTY OF VICI AND
SHALL BE RETURNED UPON DEMAND.
R
Rev.:
Sheet:
By:
Description:
ECN no:
NM Plus FID-Station with PRB
water and hydrogen flow diagram 06.10.2020
06.10.2020
SBU
SB
1
1/1
NM FID STATION 100 300 600 1000
Cell DB-CELL-MI DB-CELL-MU1 DB-CELL-MU2 DB-CELL-MU3
Gas Liquid Separator (GLS) DB-RH200-010
Over Pressure Relief Valve DB-H200-035
Perma Pure Tubes DB-H200-034
Pressure Release Block (PRB) DB-10638
Dryer DB-NMP200-000 DB-NMP200-001
PG FID STATION 100 250
Cell DB-CELL-MI DB-CELL-MU1
Gas Liquid Separator (GLS) DB-RH200-010
Over Pressure Relief Valve DB-H200-035
Perma Pure Tubes DB-H200-034
Pressure Release Block (PRB) DB-10638
NM Plus Fluidics - Zero Air Part
NM Plus Fluidics - Hydrogen Part

12
NM & PG PLUS FID STATIONS
USER MANUAL
Version 1.03.0000
www.vicidbs.com
ZERO AIR PART 1800 5000
Inlet Filter DB-10567
Pressure Regulator DB-RH200-015
Flow Restrictor DB-5000-0051 DB-5000-0052
Catalyst Oven DB-10494 DB-10495
Cooling Coil DB-RH200-026 DB-RH200-027
Check Valve DB-10640
Outlet Filter DB-10641
5.4.2. Electronics
PG Plus Electronics
System:
Schematic no:
Date:
Created:
Checked:
Released:
THIS DOCUMENT AND THE INFORMATION WHICH
IT CONTAINS SHALL NOT BE USED, EXPLOITED
OR SOLD, AND SHALL NOT BE REVEALED OR
DISCLOSED TO OTHERS WITHOUT THE EXPRESS
WRITTEN PERMISSION OF VICI. THIS DOCUMENT
SHALL REMAIN THE PROPERTY OF VICI AND
SHALL BE RETURNED UPON DEMAND.
R
Rev.:
Sheet:
By:
Description:
ECN no:
PG Plus FID-Station
electrical diagram 20.04.20
08.06.20
SBU
SB
1
1/2

13
NM & PG PLUS FID STATIONS
USER MANUAL
Version 1.03.0000
www.vicidbs.com
NM Plus Electronics
System:
Schematic no:
Date:
Created:
Checked:
Released:
THIS DOCUMENT AND THE INFORMATION WHICH
IT CONTAINS SHALL NOT BE USED, EXPLOITED
OR SOLD, AND SHALL NOT BE REVEALED OR
DISCLOSED TO OTHERS WITHOUT THE EXPRESS
WRITTEN PERMISSION OF VICI. THIS DOCUMENT
SHALL REMAIN THE PROPERTY OF VICI AND
SHALL BE RETURNED UPON DEMAND.
R
Rev.:
Sheet:
By:
Description:
ECN no:
NM Plus FID-Station with PRB
electrical diagram 20.04.20
08.06.20
SBU
SB
1
1/2
NM FID STATION 100 300 600 1000
Power Inlet DB-H200-045
Power Supply DB-PH200-003 DB-PH200-004
IO Board DB-10155
Display Board DB-10648
Display Membrane DB-H200-042
Mainboard DB-RH201-001 DB-RH204-001 DB-RH206-001 DB-RH207-001
Inlet Fan DB-H200-040
Outlet Fan DB-H200-040

14
NM & PG PLUS FID STATIONS
USER MANUAL
Version 1.03.0000
www.vicidbs.com
PG FID STATION 100 250
Power Inlet DB-H200-045
Power Supply DB-PH200-003
IO Board DB-10155
Display Board DB-10648
Display Membrane DB-H200-042
Mainboard DB-RH201-008 DB-RH203-008
Inlet Fan DB-H200-040
Outlet Fan DB-H200-040
5.5. DIMENSIONS
690 mm (27 in)
680 mm (26.7 in)
150 mm (6 in)

15
NM & PG PLUS FID STATIONS
USER MANUAL
Version 1.03.0000
www.vicidbs.com
5.6. WEIGHT
H2 FLOW RATE CONFIGURATION AIR FLOW RATE NM PLUS FID STATION
100 mL/min 1800/5000 41 kg (90.4 lbs)
300 mL/min 1800/5000 42 kg (92.6 lbs)
600 mL/min 1800/5000 43 kg (94.8 lbs)
1000 mL/min 1800/5000 44 kg (97 lbs)
H2 FLOW RATE CONFIGURATION AIR FLOW RATE PG PLUS FID STATION
100 mL/min 1800/5000 39 kg (86 lbs)
250 mL/min 1800/5000 39 kg (86 lbs)
5.7. TRANSPORT AND STORAGE
Temperature Minimum -15ºC (59ºF), Maximum 35ºC (95ºF)
Humidity Less than 90% RH, non-condensing
Shocks and Vibrations during transport Shocks <1g; Vibrations <0.2g/5Hz
Instrument position Horizontal
The above mentioned values are considered for packing.
Recommendations for Transport:
If the instrument needs to be shipped back to the factory for repair, the gas generator should be packed in its
original packaging with the inlets and outlets protected against any accidental
exposure to dust or particles.
Purge water before moving the instrument. Do not move when it is full of water.

16
NM & PG PLUS FID STATIONS
USER MANUAL
Version 1.03.0000
www.vicidbs.com
5.8. FUSES AND VOLTAGE SETTINGS
Fuse values depend on voltage and device settings. Use only 5x20mm fuse slow blow.
INSTRUMENT SETTINGS INPUT VOLTAGE
SETTING (V AC)
FUSES (A T)
PARTS FUSE MARK
Hydrogen Part F3 110 6.3
220 4
Zero Air Part 1500 F2 110 2
220 2
Zero Air Part >1500 F2 110 6.3
220 6.3
Check the setting of the voltage selector on the rear of the unit. The set voltage is indicated in the white
square.
• Use only 240 V AC or 120 V AC settings and change fuses if needed.
• Turn off the instrument before changing the voltage or fuse.
To change the voltage or fuse, proceed as follows:
Use a small at screwdriver to push the snap clip of voltage selector insert to
remove it.
B. To change the fuse value, just replace it. Use a screwdriver to unscrew the
cap from fuse holder F3. Replace the fuse using a 5x20mm fuse, and screw the
cap into its original position.
A. To change the voltage, spin the white
holder. Re-insert the voltage selector and
check to assure the white window shows the
desired voltage.

17
NM & PG PLUS FID STATIONS
USER MANUAL
Version 1.03.0000
www.vicidbs.com
6. INSTALLATION AND INITIAL START-UP
6.1. RECEIVING THE GENERATOR
All units have been carefully inspected before transport. Visual checks for damage and functional tests
should be performed upon receipt. Any damage must be immediately noted and reported. The generator
must only be returned according to the shipping instructions provided.
Keep all of the ORIGINAL packaging for instrument return.
6.2. INSTALLING THE GENERATOR
The hydrogen generator must be placed on a at, level, vibration-free, shock-free surface. Do not place the
generator over a source of heat, as this may cause the device to overheat. The unit should not be in contact
with any other objects on any side, and the air inlet must not be blocked. Leave at least 30 cm (11.8 in) of
free space at the rear for ventilation. Do not operate the generator in a sealed or unventilated room, or in
close proximity to open ame or other sources of ignition. Do not operate the generator at below freezing
temperatures. Operation is guaranteed at operating temperatures between +15 and +40°C (59 to 10ºF).
• Normal precautions for any
hydrogen supply should be taken
when using the generator.
• DO NOT use in sealed or
unventilated rooms.
• DO NOT use in close proximity of
open ames or other sources of
ignition.
Place the GC-MS unit as showed here, in the
middle of the upper surface of the Plus FID
Station.

18
NM & PG PLUS FID STATIONS
USER MANUAL
Version 1.03.0000
www.vicidbs.com
6.3. GAS CONNECTIONS
Pure dry hydrogen at regulated pressure is available at the hydrogen outlet port at the rear of the
generator. This port must be connected to 1/8” tubing using a stainless-steel or copper Swagelok
connector. Teon connectors are not suitable. The pressure at this port is adjusted and shown on the
display. The hydrogen relief port at the rear of the unit can be connected to an exhaust hood or other vent
system.
Install compressed air with a ¼” tubing to AIR IN. The air quality must meet the minimum specication
according ISO8573-1:2010 Class 1.2.1. The pressure must be between 4.5 to 10 bar (65 to 160 psig).
The AIR OUT is a 1/8” Swagelok connector.
The line from the relief port should never connect in such a way that back pressure
can develop.
Remove the plugs from the
hydrogen vent before operating the
unit and connect H2 vent to a purge
tube. Keep these plugs for
further shipments of the unit.

19
NM & PG PLUS FID STATIONS
USER MANUAL
Version 1.03.0000
www.vicidbs.com
6.4. FILLING THE WATER TANK
The Plus FID Station has an internal water tank included in its chassis. The tanks must be relled with
deionized water with conductivity below 1 µS. Follow these steps in order to ll the automatic water tank
system correctly.
1. Fill the external tank provided with
deionized water (below 1 µS/cm).
4. Place the tank higher than the generator (the
system is relled by gravity). Water will begin to ow
from the tank into the generatoe.
• Disconnect the external tank when max is reached to avoid overll.
• ONLY use deionized water in the generator. Water containing metallic, salt, or
other inonic impurities will contaminate/damage the cell, and will void the
warranty.
2. Pull the front panel of the generator by handles as
showed in photo (g.1). You have the access to the
relling tting (g.2).
3. Connect the external water tank tting to
the rell tting on the front of the instrument.
5. Disconnect the tank when the water
has reached the MAX level shown on the
side of the unit.