Victoria Arduino ADONIS 2 gruoups User manual

35
EN
Congratulations, you have chosen an unique in its kind machine.
Read carefully what is advised in the instruction manual for “setting-up” of your “ADONIS”.
You will see how easy it is to make delicious coffee and creamy cappuccinos.
With the passing of time, you will also realise how little maintenance is needed.
Victoria Arduino
ADONIS

36
EN
ADONIS

37
EN
Model: ADONIS 2 gruoups - Net weight: 84 Kg - Gross weight: 90 Kg - Thermal power: 4500 W - Boiler capacity 14 lt - Volts 230-380V 50/60Hz
The approval mark certifies that all machines have been subjected to accurate inspection tests and checks
ADONIS
Model: ADONIS 3 gruoups - Net weight: 98 Kg - Gross weight: 108 Kg - Thermal power: 5000 W - Boiler capacity 17 lt - Volts 230-380V 50/60Hz

38
EN
INDEX
TECHNICAL CHARACTERISTICS ...................... 37
1. GENERAL REMARKS ON
THE CONSIGNMENT .......................................... 39
1.1 SAFETY REGULATIONS.................................................................... 39
2. DESCRIPTION ..................................................... 41
2.1 ACCESSORIES LIST ......................................................................... 42
3. TRANSPORT AND HANDLING ........................... 43
3.1 APPLIANCE IDENTIFICATION............................................................ 43
4. INSTALLATION AND PRELIMINARY
OPERATIONS ...................................................... 44
5. ADJUSTMENTS TO BE MADE BY
A QUALIFIED TECHNICIAN ONLY...................... 46
5.1 FILLING BOILER MANUALLY............................................................. 46
5.2 PRESSOSTAT / PUMP ADJUSTMENT................................................ 47
5.2.1 PUMPADJUSTMENT...........................................................................................47
5.2.2 PRESSOSTAT ADJUSTMENT...............................................................................47
5.3 HOT WATER ECONOMISER ADJUSTMENT ......................................48
5.4 CLOCK BATTERY REPLACEMENT.............................................................49
6. USE ...................................................................... 50
6.1 TURNING THE MACHINE ON............................................................ 50
6.2 LED SWITCH ON ..............................................................................52
6.3 BUTTONS KEY (Selection Configuration)............................................. 52
6.4 STEAM FLOW ADJUSTMENT............................................................ 53
6.4 ADJUSTING THE TURBOCREAM NOZZLE (If Fitted).......................... 53
6.4 ADJUSTING THE AUTOSTEAM NOZZLE (If Fitted) ............................. 54
7. PROGRAMMING.................................................. 55
7.1 KEY................................................................................................... 55
7.2 PROGRAMMING..............................................................................................55
8. CLEANING AND MAINTENANCE........................ 65
8.1 SWITCHING OFF THE MACHINE ...................................................... 65
8.2 CLEANING THE OUTSIDE OF THE MACHINE...................................65
8.3 CLEANING THE STAINLESS COFFEE-HOLDERS..............................65
8.4 CLEANING THE UNIT WITH THE AID OF THE BLIND FILTER ............ 66
8.5 CLEANING FILTERS AND FILTER-HOLDERS .................................... 66
9. MACHINE FUNCTION MESSAGES .................... 67

39
EN
1.1 SAFETY REGULATIONS
 The present manual is an integral and essential
part of the product and will have to be handed over
to the user. Read carefully the written warnings in the
present manual as they give important suggestions
concerning the safety of installation and set-up, use
and maintenance. Keep this manual in a safe place for
further information.
฀ POLLUTION DANGER
 After removing the packaging, check the integral
parts of the machine are intact. If in doubt, do not use
the machine and contact the professionally qualified
personnel. The elements of the packaging must be
kept out of children’s reach as they can be potential
sources of danger and they mustn’t be disposed of in
the environment.
 Before connecting the machine, make sure that the
data of the plate correspond to those of the electrical
distribution network. The plate is located under the
machine’s base. The installation has to be carried out
in compliance with the regulations of the Country where
the machine is set-up, according to the instructions by
the manufacturer and qualified personnel.
The manufacturer can’t be considered responsible for
possible damage caused by failure in earthing the plant.
For the electrical safety of this machine it is obligatory
to arrange the earthing plant, contact an electrician
with proper and certified technical suitability, to check
the electrical capacity of the plant is adequate to the
maximum power of the machine, stated on the plate.
In particular the electrician will have to make sure that
the section of the plants’ cables is suitable to the power
absorbed by the machine.
The use of adaptors, multi-sockets and extensions is
forbidden. If their use is necessary, it is compulsory to
call a licensed electrician.
 The machine must be set-up according to the
sanitary and health regulations valid for hydraulic
plants. For the hydraulic plant contact an authorised
technician.
 This machine will have to be used only for the pur-
pose described in this manual.
The manufacturer can’t be considered responsible
for possible damage caused by improper, wrong, or
unreasonable uses.
฀ WARNING
Before using the machine read carefully and completely
the instruction manual, safety regulations and the
machine tuning/ directions.
 The use of any electrical device must comply with
fundamental regulations. In particular:
• do not touch the machine with wet hands or feet;
• do not use the machine barefoot;
1. GENERAL REMARKS ON THE CONSIGNMENT

40
EN
• do not use extensions in places used as a bath or
shower;
• do not pull the supply cable, to disconnect the
machine from the supplying net;
• do not leave the machine exposed to atmospheric
agents (rain, sun, etc);
• do not allow the machine to be used by children or
by non-authorised personnel that haven’t read and
understood this manual.
 The authorised technician has to, before carrying
out any maintenance operation, unplug the socket after
having switched off the machine switch.
 bis For the cleaning operations bring the machine
to energetic state “O”, that is to say “machine is
switched off and socket unplugged” and keep exclu-
sively to what is stated in the present manual.
 In case of breakdown or wrong functioning of the
machine, switch it off.
Any intervention is strictly forbidden.
Contact exclusively professionally authorised personnel.
The possible repair of the products will have to be made
by the manufacturer only or by an authorised service
using exclusively original spare parts.
Non-compliance with the above stated can compromise
the safety of the machine.
 When setting it up, the licensed electrician will
have to check an omni-polar switch is provided by the
actual safety regulations with opening distance from the
contacts the same or bigger than 3 mm.
 To avoid dangerous overheating, we do recommend
you uncoil the supply cable to its full length.
 The user mustn’t replace the supply cable of this
machine. In case of damage, switch the machine off
and for its replacement contact exclusively profession-
ally qualified personnel.
In the event that you decide not to use a machine of
this kind anymore, we advise you make it ineffective by
unplugging the socket, then cut the supply cable.
฀ WARNING DANGER OF POLLUTION
Do not dispose of the machine in the environment: for
waste disposal, contact a specialised authorised centre
or contact the manufacturer that will give you informa-
tion about this.
! To help the aeration of the machine place it 15 cm
from the walls or from other machines on the aeration
side.
฀ WARNING DANGER OF BURNING
" When using the vapour spear, pay much attention
and do not place hands under it and do not touch it
immediately after its use.
# Remember that before carrying out any set-up
operation, maintenance, download, or tuning, the quali-
fied operator has to wear working gloves and safety
shoes.

Fig. 1
41
EN
2. DESCRIPTION
Adjustment Dial
Steam Flow
Programming Key
LCD Display
Select Buttons
Hot Water / Steam
Delivery Unit Buttons
Filter-Holder
Manual Steam Nozzle
Delivery Unit
Autosteam Nozzle
Piede Regolabile
Hot Water Nozzle
Electric Cup-Warmer
Programming Keys
Cup Rack
Drip Tray
Machine Main
Switch

Fig. 2
42
EN
2.1 ACCESSORIES LIST
CODE DESCRIPTION 2 GROUPS 3 GROUPS
A01 Filling tube ⅜” 1 1
A02 Worktop draining tube
Ø 25 mm - l. 150 cm 1 1
A03 Filter-holder 3 4
A04 Double filter 2 3
A05 Single filter 1 1
A06 Blind filter 1 1
A07 Spring 3 4
A08 Double delivery spout 2 3
A09 Single delivery spout 1 1
A10 Coffee presser 1 1
A11 ‘U’ and ‘T’ keys 1 1
A12 Microfibre cloth 1 1
A13 DVD 1 1
A14 Overall 1 1
A13 A12
A02
A01
A11
A14
A10
A05
A06
A04
A07
A03
A08
A09

43
EN
3. TRANSPORT AND HANDLING
3.1 APPLIANCE IDENTIFICATION
When contacting the manufacturer, Victoria Arduino for
any reason, always quote the machine serial number.
The machine is transported on pallets containing several
machines inside boxes secured to the pallet by straps.
Before performing any transport or handling operation,
the operator must:
• wear safety gloves and footwear and overalls with
elasticised ends.
Pallets must be transported using an adequate lifting
mechanism (fork-lift truck type).
฀ CAUTION: COLLISION OR CRUSHING HAZARD
During the entire handling operation, the operator must
make sure no one or nothing is inside the operating
area.
Slowly lift the pallet to about 30 cm from the ground and
move to the loading area. After making sure there are no
obstacles, persons or things, proceed with loading.
Once at destination, always using an adequate lifting
mechanism (eg. fork-lift), after making sure there is no
one or nothing within the unloading area, lower the pallet
to about 30 cm from the ground and transport it to the
storage area.
฀ CAUTION: COLLISION OR CRUSHING HAZARD
Before performing the following operation, make sure the
load is in place and is not likely to fall when the straps
are cut.
The operator, wearing safety gloves and footwear, must
now cut the straps and store the product. To perform this
operation, check the technical characteristics of the prod-
uct to determine the weight of the machine to be stored
and take consequent precautions.
฀ CAUTION: POLLUTION HAZARD
Once the machine has been freed of the pallet or con-
tainer, do not discard these in the environment - pollution
hazard.

Fig. 3
Fig. 4
44
EN
After unpacking, assess that the machine and its
accessories unit are complete, then proceed as fol-
lows:
• place the machine so that it is level on a flat sur-
face;
• assemble its supporting feet by inserting the insert
into the cylindrical unit (see Fig. 3);
• twist the rubber foot into the screw thread inside
the unit (see Fig. 3);
• screw the whole assembled unit into the allotted
setting for the machine’s adjustable feet;
• level the machine by regulating the adjustable
feet;
E฀ NOTE
The unit grooves have to face upwards, as shown in the
following illustration.
It is advisable to install a softener (1) and then a mesh
filter (2) on the external part of the plumbing system, dur-
ing preliminaries and after levelling the machine.
In this way impurities like sand, particles of calcium, rust
etc will not damage the delicate graphite surfaces and
durability will be guaranteed.
Following these operations, connect the plumbing sys-
tems as illustrated in the following figure.
฀ WARNING
Avoid throttling in the connecting tubes.
Assess that the drain pipe (3) is able to eliminate waste.
KEY
0Softener
1Mesh filter
2Drain Ø 50 mm
4. INSTALLATION AND PRELIMINARY OPERATIONS
2
3
1

1 2 3 4
5
Fig. 5
1 2 3 4
5
Fig. 6
45
EN
E฀ NOTE
For a correct functioning of the machine the water
works pressure must not exceed 4 bars.
Otherwise install a pressure reducer upstream of the
softener; the internal diameter of water entrance tube
must not be less than 6mm (⅜”).
฀ CAUTION RISK OF SHORT CIRCUITS
The machine must always be protected by an automatic
omnipolar switch of suitable power with contact open-
ings of equal distance or more than 3mm.
Nuova Simonelli is not liable for any damage to peo-
ple or objects due to not observing current security
measures.
Prior to connecting the machine to the electrical mains,
assess that the voltage shown on the machine’s data plate
corresponds with that of the mains.
If it does not, carry out the connections on the basis of the
available electrical line, as follows:
• for V 380 / 3 phases voltage + Neutral:
• for V 230 / monophase voltage:
KEY
0Black
1Grey
2Brown
3Blue
4Yellow-green

Fig. 8
Fig. 7
46
EN
5.1 FILLING BOILER MANUALLY
E฀NOTE
This operation must be carried out with the machine
turned off.
All models ADONIS are equipped with a level gauge to
keep the water level inside the boiler constant.
When using the machine for the first time, it is advisable
to fill the boiler by hand to avoid damaging the electrical
resistor and turning on the electronic protection.
If this should happen, just turn the machine off and then
start it up again to complete its loading procedure (see
chapter “MACHINE FUNCTIONS MESSAGE – LEVEL
ERROR”).
To fill the boiler manually for the first time, proceed
as follows:
• remove the grid and the drip tray;
• remove the protective metal sheet by unscrewing
the two side screws "A" as shown in the following
illustration;
• turn the manual “A” level tap so that water will
enter the boiler;
• after about 45 seconds, shut off the valve ”A” as
illustrated in the following figure;
• switch on the machine (see the chapter
“SWITCHING ON THE MACHINE”).
5. ADJUSTMENTS TO BE MADE BY A QUALIFIED TECHNICIAN ONLY
A
A

Fig. 11
Fig. 9
Fig. 10
47
EN
5.2 PRESSOSTAT / PUMP ADJUSTMENT
E฀ NOTE
This operation can be carried out while the machine
is turned on.
To adjust the service pressure of the boiler, thus
regulating the water temperature, according to the
various functions and needs of the coffee desired,
proceed as follows:
• remove the grid and the drip tray;
• remove the protective metal sheet by unscrewing
the two side screws "A" as shown in the following
illustration;
5.2.1 PUMP ADJUSTMENT
• Turn the pump registration screw, turning it clock-
wise to INCREASE and counter clock wise to
DECREASE the pressure;
Advisable pressure: 9 bar
5.2.2 PRESSOSTAT ADJUSTMENT
• Use the adjustment screw for the pressure switch
to INCREASE (anticlockwise) or REDUCE (clock-
wise) the pressure in the boiler tank;
Advisable pressure: 1 - 1,4 bar
(according to the kind of coffee)
A

Fig. 12
Fig. 13
48
EN
• The set pump pressure is displayed in the bottom
section "B" of the pressure gauge, inside the
machine (see Fig. 12);
• The pressure set on the pressure switch is dis-
played in the top section "C" of the pressure gauge,
inside the machine (see Fig. 12);
At the end of the adjustment process, refit the sheet
metal guard on the relevant housing and secure it in
place with the two side screws. Refit the drip tray and
the work surface grid.
• To access the pressure gauge, remove the cup
warmer section on the left by loosening the two
screws "D" as illustrated in the following figure.
5.3 HOT WATER ECONOMISER
ADJUSTMENT
E฀NOTE
This operation can be carried out while the machine
is turned on.
All models ADONIS are equipped with a hot water mixer
tap which adjusts the water temperature and optimises the
system’s performance.
To adjust the hot water economiser, turn the registration
knob.
• The hot water economiser is located inside the
machine.
C
B
D

Fig. 14 Fig. 15
49
EN
OFF
S TO P CL OCK
• To access the economiser, remove the cup warmer
section on the left by loosening the two screws "D"
as illustrated in the following figure.
• Turn the adjustment knob ANTICLOCKWISE /
CLOCKWISE to INCREASE / REDUCE the tempera-
ture of the hot water;
• when the operation has been completed, screw
the protective panel back on.
5.4 CLOCK BATTERY REPLACEMENT
The electronic control unit is equipped with a lithium bat-
tery to provide the clock with an approximately three-year
autonomy period, after which replacing the battery may
prove necessary.
In case the machine has remained unutilised for a long
time, the clock can be blocked by proceeding as follows:
• with the machine off the display will read:
• press the ENTER key for 5 seconds; the display
will read:
The clock will start up again as soon as the machine is
plugged in once more.
D

Fig. 16
50
EN
฀ WARNING
Replacement of the lithium battery must be carried out
EXCLUSIVELY by Qualified Technician.
Nuova Simonelli cannot be held liable for any damage
to people or things due to non observance of the safety
prescriptions described in this booklet.
Before starting to use the appliance, the operator must be
sure to have read and understood the safety prescriptions
contained in this booklet.
The ADONIS model is equipped with a display key T
and a technical key U. With the display key Tit is pos-
sible to access the normal operating functions, while
programming menus can be seen but not modified
(Chapter 7).
The technician Ukey allows you to access all the func-
tions and to modify the parameters of the programming
menu.
6.1 TURNING THE MACHINE ON
• Plug the machine in and position the main switch
"A" on “I”.
• The unlit display will read:
6. USE
OFF
A

51
EN
E฀ NOTE
The machine is not operative in that the main switch
only supplies the electronic card.
฀ WARNING
For electronic card maintenance, turn the machine off
by means of the external main switch or disconnect the
plug.
MANUAL SWITCHING ON / OFF
Automatic On / Off NOT PROGRAMMED
SWITCH ON
press the RESET key for 2 seconds, the buzzer will beep,
the display will light up to indicate the release of the
EPROM for about 1 second.
The control unit will start up an auto diagnosis cycle
to check the functions, all the selection keys will light
up.Once the check is completed the display will read:
with the day and time. When 110°C has been reached,
the heating message will disappear and will be replaced
by the words:
E฀ NOTE
On completion of the check up all the selection keys
are activated.
฀ WARNING
In case the auto diagnosis indicates error or malfunc-
tion, call an assistance centre; the operator MUST NOT
intervene.
POWER OFF
press the RESET key for 2 seconds; the machine will turn
off and the display will read:
Automatic On / Off PROGRAMMED
The machine will SWITCH ON at the first programmed
switch-on time (see the section entitled PROGRAMMING
at the paragraph PROGRAMMING ON - OFF).
The control unit will perform an auto diagnosis of all func-
tions and all of the selection keys will light up.
Once the diagnosis is complete, the display will read as
follows:
H EA TING
M A CHINE RE A D Y
OFF
H EA TING

Fig. 17
52
EN
with the date and time. Once the temperature of 110°C has
been the word “Heating” will disappear to be replaced by:
E฀ NOTE
Once the auto diagnosis has been completed all the
keys are activated.
฀ WARNING
In case the auto diagnosis indicates error or malfunc-
tion, call the assistance centre; the operator MUST NOT
intervene.
The machine will SWITCH OFF at the first time set for stop-
ping the coffee maker (see chapter on PROGRAMMING
and paragraph on PROGRAMMING ON – OFF).
E฀ NOTE
the machine can be switched on or off manually as
indicated in the previous paragraph.
6.2 LED SWITCH ON
• Plug the machine in and position the main switch
"B" on “I”.
6.3 BUTTONS KEY
Selection Configuration
M A CHINE RE A D Y
1 Small coffee 2 Small coffees
1 Long coffee 2 Long coffees
Continuous Hot Water
Steam Cup Warmer
B

Fig. 18
Fig. 19
Fig. 19.A
Fig. 19.B
53
EN
6.4 STEAM FLOW ADJUSTMENT
Use the dial to increase/reduce the flow of steam inject-
ed into the milk, as illustrated in the following figure.
6.5 ADJUSTING THE TURBOCREAM
NOZZLE
(If Fitted)
To increase/reduce the amount of air injected into the
milk from the TurboCream nozzle (and therefore to
increase/reduce the amount of foam in the heated milk)
proceed as illustrated in Fig. 19:
0Loosen the stainless steel tube (1) as illustrated in
Fig. 19.A.
1To increase/reduce the amount of air, tighten (turn-
ing clockwise) or loosen (turning anticlockwise) the
Teflon tube (2) as illustrated in Fig. 19.B.
2Tighten the stainless steel tube again.
E฀ NOTE
By reducing or increasing the length (tightening or
loosening) the tube/Teflon tube by a few fractions of a
mm/mm, there is a significant difference in the amount
of foam in the heated milk.
2
1

Fig. 20
Fig. 20.A
Fig. 20.B
54
EN
6.6 ADJUSTING THE AUTOSTEAM
NOZZLE
(If Fitted)
To increase/reduce the amount of air injected into the
milk from the TurboCream nozzle (and therefore to
increase/reduce the amount of foam in the heated milk)
proceed as illustrated in Fig. 20:
0Loosen the stainless steel tube (1) as illustrated in
Fig. 20.A.
1To increase/reduce the amount of air, tighten (turn-
ing clockwise) or loosen (turning anticlockwise)
the Teflon tube (2) as illustrated in Fig. 20.B.
2Tighten the stainless steel tube again. 3As far as concerns temperature settings, see the
relevant programming section.
E฀ NOTE
By reducing or increasing the length (tightening or
loosening) the tube/Teflon tube by a few fractions of a
mm/mm, there is a significant difference in the amount
of foam in the heated milk.
2
1