Viega 8142 User manual

for WB with single-hole fitting
Model Year built:
8142 from 09/2005
en_INT
Viega Eco Plus washbasin corner element
Instructions for Use

Viega Eco Plus washbasin corner element 2 from 24

Table of contents
1About these instructions for use 4
1.1 Target groups 4
1.2 Labelling of notes 4
1.3 About this translated version 5
2Product information 6
2.1 Standards and regulations 6
2.2 Intended use 6
2.2.1 Areas of use 6
2.3 Product description 7
2.3.1 Overview 7
2.3.2 Compatible components 7
2.3.3 Sound protection 7
2.3.4 Technical data 8
3Handling 9
3.1 Assembly information 9
3.1.1 Mounting conditions 9
3.1.2 Installation dimensions 9
3.1.3 Required tools 9
3.2 Assembly 11
3.2.1 Mounting element 11
3.3 Disposal 24
Table of contents
Viega Eco Plus washbasin corner element 3 from 24

1 About these instructions for use
Trade mark rights exist for this document, further information can be
found at viega.com/legal .
1.1 Target groups
The information in this instruction manual is directed at the following
groups of people:
nHeating and sanitary professionals and trained personnel
nDrywall builder
It is not permitted for individuals without the abovementioned training or
qualification to mount, install and, if required, maintain this product. This
restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.
1.2 Labelling of notes
Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.
DANGER!
This symbol warns against possible life-threatening injury.
WARNING!
This symbol warns against possible serious injury.
CAUTION!
This symbol warns against possible injury.
NOTICE!
This symbol warns against possible damage to property.
Notes give you additional helpful tips.
About these instructions for use
Viega Eco Plus washbasin corner element 4 from 24

1.3 About this translated version
This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e. g. EN) and/or in Germany
(e. g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The relevant national laws, stand-
ards, regulations, directives and other technical provisions take priority
over the German/European directives specified in this manual: The
information herein is not binding for other countries and regions; as said
above, they should be understood as a recommendation.
About these instructions for use
Viega Eco Plus washbasin corner element 5 from 24

2 Product information
2.1 Standards and regulations
The following standards and regulations apply to Germany / Europe.
National regulations can be found on the relevant web site of your
country at viega.com/standards .
Regulations from section: Fields of application / Mounting conditions
Scope / Notice Regulations applicable in Ger-
many
suitable masonry walls EN 1996-1-1
suitable concreted walls DIN 1045
suitable support profiles DIN 18183
Regulations from section: Sound protection
Scope / Notice Regulations applicable in Ger-
many
Fulfilled noise protection require-
ments
DIN 4109
Fulfilled noise protection require-
ments
DIN 4109 (additional sheet 2)
Fulfilled noise protection require-
ments
VDI 4100 SSt I-SSt II
2.2 Intended use
2.2.1 Areas of use
The Viega Eco Plus washbasin element is suitable for mounting on
masonry wall constructions and support profiles pursuant to the regula-
tions in section Ä„Regulations from section: Fields of application /
Mounting conditions“ on page 6 .
Product information
Viega Eco Plus washbasin corner element 6 from 24

2.3 Product description
2.3.1 Overview
3
4
5
6
7
1
2
Fig. 1: Components and scope of delivery
1 - Viega Eco Plus element
2 - adjusting screws
3 - threaded bolt
4 - mounting bracket for drain elbow
5 - connections for wall plates
6 - drain elbow
7 - adjustable feet
2.3.2 Compatible components
The element is compatible with all common washbasin ceramics, even
with larger projection (barrier-free).
2.3.3 Sound protection
The washbasin element complies with the noise insulation requirements
specified in section Ä„Regulations from section: Sound protection“
on page 6 .
Product information
Viega Eco Plus washbasin corner element 7 from 24

2.3.4 Technical data
The product has the following technical data:
drain elbow DN 40 / 50
Rubber nipple DN 40 / 30
Construction height 980 mm–1130 mm
Product information
Viega Eco Plus washbasin corner element 8 from 24

3 Handling
3.1 Assembly information
3.1.1 Mounting conditions
The element is suitable for mounting on masonry wall constructions and
support profiles pursuant to the regulations in section
Ä„Regulations
from section: Fields of application / Mounting conditions“ on page 6 .
The element may only be mounted on even wall surfaces.
With the construction height, the marked height of the upper edge of
the finished floor must be observed.
3.1.2 Installation dimensions
Fig. 2: Dimensions
3.1.3 Required tools
The following tools are required for mounting the washbasin element:
Suitable walls
Construction height
Handling
Viega Eco Plus washbasin corner element 9 from 24

ndrill with 10 mm drill bit
nratchet with sockets: 13 mm / 17 mm
nfork or ring spanner: 13 mm / 17 mm
Handling
Viega Eco Plus washbasin corner element 10 from 24

3.2 Assembly
3.2.1 Mounting element
980 - 1130
Position the element at construction height.
The element can be adjusted continuously from 980–1130 mm.
Align element.
Mark drill holes.
Mounting in a corner (approx. 90°)
Handling
Viega Eco Plus washbasin corner element 11 from 24

980 - 1130
Drill holes for the wall fixing and the floor supports.
Hit dowel (10 mm) into the wall/floor.
Handling
Viega Eco Plus washbasin corner element 12 from 24

Screw the element into the wall and into the floor (SW 13 / 17).
Handling
Viega Eco Plus washbasin corner element 13 from 24

Connect water and wastewater pipe.
Clad the element with a single layer of IFGP cladding panels
(1 x 12.5 mm).
Handling
Viega Eco Plus washbasin corner element 14 from 24

980 - 1130
Position the element at construction height.
The element can be adjusted continuously from 980–1130 mm.
Remove the floor support where the drainage line is.
Align element.
Mark drill holes (5 wall fixings and one floor support).
Mounting in the corner (approx. 90°) with cladding of the drainage line
Handling
Viega Eco Plus washbasin corner element 15 from 24

980 - 1130
Drill holes for the wall fixing and the floor support.
Hit dowel (10 mm) into the wall/floor.
Handling
Viega Eco Plus washbasin corner element 16 from 24

Screw the element into the wall and into the floor (SW 13 / 17).
Handling
Viega Eco Plus washbasin corner element 17 from 24

Connect water and wastewater pipe.
Clad the element with a single layer of IFGP cladding panels
(1 x 12.5 mm).
Handling
Viega Eco Plus washbasin corner element 18 from 24

980 - 1130
Position the element at construction height.
The element can be adjusted continuously from 980–1130 mm.
Align element.
Mark drill holes (4 wall fixings and two floor supports).
Mounting on the wall (one-sided fixing)
Handling
Viega Eco Plus washbasin corner element 19 from 24

980 - 1130
Drill holes for the wall fixing and the floor support.
Hit dowel (10 mm) into the wall and the floor.
Handling
Viega Eco Plus washbasin corner element 20 from 24