Viessmann VITOSOLIC 200 User manual

Operating instructions
for the system user
VIESMANN
Control unit for solar thermal systems
VITOSOLIC 200
5592 613 GB 5/2009 Please keep safe.

2
Please follow these safety instructions closely to prevent accidents and mate-
rial losses.
Safety instructions explained
Danger
This symbol warns against the
risk of injury.
!Please note
This symbol warns against the
risk of material losses and envi-
ronmental pollution.
Note
Details identified by the word "Note" con-
tain additional information.
Target group
These operating instructions are
designed for system users.
This appliance is not designed to be
used by persons (including children) with
limited physical, sensory or mental
capacities, or lacking experience and/or
knowledge, unless they are supervised
by a person responsible for their safety,
or have received instructions from such
a person as to how to use the appli-
ance.
!Please note
Children should be supervised.
Ensure that children never play
with the appliance.
Danger
Incorrect work on the system can
lead to life-threatening acci-
dents.
Work on electrical equipment
must only be carried out by a
qualified electrician.
In case of fire
Danger
Fire creates the risk of burning
and explosions.
■ Shut down the system.
■ Use a tested fire extinguisher,
class ABC.
Ancillary components, spare and
wearing parts
!Please note
Components that are not tested
with the system may lead to sys-
tem damage, or may affect its
functions.
Installation or replacement work
must only be carried out by quali-
fied personnel.
Safety instructions
For your safety
5592 613 GB

3
Introductory information
Commissioning..................................................................................................... 4
Operation............................................................................................................ 5
Scanning options
Scanning actual values........................................................................................ 6
Scanning messages............................................................................................. 7
Scanning statement values.................................................................................. 8
Scanning the heat meter...................................................................................... 8
What to do if...
The solar thermal system does not start.............................................................. 10
There is no DHW available................................................................................... 10
The display appears dark..................................................................................... 11
The display illumination flashes............................................................................ 11
Scanning faults..................................................................................................... 11
Menu overview.................................................................................................... 12
Index
Index
5592 613 GB

4
The commissioning and matching up of
the control unit to local conditions and to
the structural characteristics of the build-
ing, plus the instruction of the user in
operating the system, must be carried
out by your heating contractor.
Introductory information
Commissioning
5592 613 GB

5
Controls
B
30.04.2009
Tcol
Tcylb
10:59
47.7 °C
35.4 °C
A
AStandard display
The standard display will automat-
ically show after approx. 4 min.
BOK key; to confirm your selection
or save the setting.
This takes you to the previous
step in the menu or cancels a set-
ting that has been started.
/ Cursor keys
To scroll through the menu.
/ Cursor keys
To adjust values.
To change between standard dis-
play and main menu.
The display can show four lines at a time.
The arrow on the l.h. side of the display
highlights the available menu item.
You can scroll through the menu with the
/ keys.
Operation
Operation
5592 613 GB

6
Press the following keys:
1. for the "Main menu".
2. OK the first three actual values will
be displayed.
3. / for additional actual values,
subject to the system equip-
ment level.
4. until the "Main menu"
appears.
"Actual values" Explanation
Tcol Collector temperature in °C
Tcol2 Collector temperature in an additional collector array in °C
Tcylb Actual cylinder temperature in °C
Tcyl2b to Tcyl4b Actual cylinder temperature for additional consumers (e.g.
DHW cylinder 2) in °C
Tby Bypass temperature in °C
T-HE Temperature in an external heat exchanger in °C
Cyl. add. Auxiliary function for DHW heating
Time
Date
Relays 1 to 7 Relay condition
Sensors 1 to 12 Temperature at the respective sensor in °C
Note
If the sensor inputs are not connected, the value for "lead
break" will be displayed.
Intens. Radiation intensity in conjunction with a solar thermal sys-
tem
Note
If the sensor inputs are not connected, the value for "lead
break" will be displayed.
A diagram in the standard display ena-
bles you to scan the collector and actual
cylinder temperatures in the course of
the day. In addition, if your heating con-
tractor has enabled the heat meter, a
diagram displays the heat volume for the
past seven days.
Press the key in succession; the fol-
lowing diagrams will be displayed:
Scanning options
Scanning actual values
5592 613 GB

7
Actual cylinder temperature curve
Tcylb today
12
Collector temperature curve
Tcol today
12
Amount of heat in kWh
HM 1
7
5 5
33
6
1
Note
The right bar indicates the value of the
current day in kWh.
Scanning messages
Press the following keys:
1. for the "Main menu".
2. for "Reports".
3. OK to confirm.
4. for further displays (see the fol-
lowing table).
"Messages:" Explanation
No fault There is no fault at the solar control unit.
Loading cyl...
(only with several consum-
ers)
Consumer displayed is being heated.
Pause cyl...
(only with several consum-
ers)
Only if the "Cyclical heating" function has been ena-
bled by your heating contractor:
Pause in the heating of the displayed consumer.
Cyl set... Consumer displayed has reached its set value.
Fault A fault has occurred at the solar control unit (for "Scan-
ning the fault display", see page 11).
SW version Software version (only for service engineers)
HW version Hardware version (only for service engineers)
Scanning options
Scanning actual values (cont.)
5592 613 GB

8
Press the following keys:
1. for the "Main menu".
2. for "Solar".
3. OK to confirm.
4. for "Statement".
5. OK to confirm.
6. / for additional statement val-
ues, subject to the system
equipment level.
7. until the "Main menu"
appears.
"Statement" Explanation
Colmax Maximum collector temperature in °C
Col2max Maximum collector temperature in an additional collector
array in °C
Cylmax Maximum cylinder temperature in °C
Cly2max to
Cly4max
Maximum cylinder temperature for additional consumers (e.g.
DHW cylinder 2) in °C
Relays 1 to 7 Hours run of actuators connected at relay outputs (e.g. solar
circuit pump at R1)
Days Days run, solar control unit
To reset the values, except for days
run:
Whilst the value is displayed, press the
following keys:
1. OK "Delete?""Yes" is displayed.
2. OK to confirm.
Scanning the heat meter
Press the following keys:
1. for the "Main menu".
2. for "HM".
3. OK to confirm.
4. for "HM 1" or "HM 2".
5. OK to confirm.
6. / for additional values, subject to
the system equipment level.
Scanning options
Scanning statement values
5592 613 GB

9
7. until the "Main menu"
appears.
"HM..." Explanation
Tflow Flow temperature in °C
Tretn Return temperature in ºC
"Heat" Amount of heat in Wh
"Heat" Amount of heat in kWh
"Heat" Amount of heat in MWh
Note
Add the heat values together.
The values are not calibrated.
To reset the heat meter values:
Whilst the value is displayed, press the
following keys:
1. OK "Delete?""Yes" is displayed.
2. OK to confirm.
Scanning options
Scanning the heat meter (cont.)
5592 613 GB

10
Cause Remedy
The mains isolator is switched OFF. Switch ON the mains isolator.
The solar control unit MCB has respon-
ded (mains voltage is present, display
does not illuminate).
Contact your local heating contractor.
Collector limit temperature or set cylinder
temperature has been reached.
Wait until the respective temperature has
fallen below the relevant limit.
The solar control unit is in "manual
mode".
To select "Auto":
1. Press .
2. Press until "Manual mode" is dis-
played.
3. Press OK to confirm.
4. Press until "Relay 1" etc. is dis-
played.
5. Press OK to confirm.
6. Press the / keys for "Auto".
7. Press OK to confirm.
8. Press until "Main menu" is dis-
played.
There is no DHW available
Cause Remedy
The solar control unit is faulty. Contact your local heating contractor.
Collector temperature too high; safety
shutdown through the solar control unit.
Wait until the collector temperature has
fallen.
The set cylinder temperature is too low. Contact your local heating contractor.
Solar circuit pump faulty. Contact your local heating contractor.
The DHW cylinder is not reheated:
The operating and time program is incor-
rectly set at the boiler control unit.
Enable DHW heating.
Operating instructions of the boiler
control unit
What to do if...
The solar thermal system does not start
5592 613 GB