ViewSonic NMP580-W User manual

NMP580-W
Network Media Player
Quick Start Guide
2
Box Contents
Mounting and Installation
Attach the wireless antenna as shown in left, screw
antenna clockwise onto the post.
[Attach on the back of the monitor] Separate the Velcro pads
and stick one of them to the bottom of player. Stick the other
Velcro pad onto the back of monitor, and then attach the player
to it. Use HDMI extension cord to connect player and the
monitor.
1

中国
http://www.viewsonic.com.cn
电话：4008 988 588
香港
http://www.hk.viewsonic.com
電話：852 3102 2900
澳門
http://www.hk.viewsonic.com
電話：853 2840 3687
台灣
http://www.viewsonic.com.tw
電話：[phone]
한국
http://ap.viewsonic.com/kr/
Phone: [phone]
Singapore/Malaysia/Thailand
http://www.viewsonic.com.sg
Phone: [phone]
India
http://www.in.viewsonic.com
Phone: [phone]
United States
http://www.viewsonic.com
Phone: [phone] (Toll-Free)
1-424-233-2530 (Toll)
Canada
http://www.viewsonic.com
Phone: [phone] (Toll-Free)
1-424-233-2533 (Toll)
Europe
http://www.viewsoniceurope.com
www.viewsoniceurope.com/uk/
support/call-desk/
Australia/New Zealand
http://www.viewsonic.com.au
Phone: [phone] (AUS)
0800 008 822 (NZ)
South Africa
http://ap.viewsonic.com/za/
Latin America (Chile)
http://www.viewsonic.com/la/
http://www.viewsonic.com/la/soporte/
servicio-tecnico
Latin America (Mexico)
http://www.viewsonic.com/la/
http://www.viewsonic.com/la/soporte/
servicio-tecnico
Latin America (Peru)
http://www.viewsonic.com/la/
http://www.viewsonic.com/la/soporte/
servicio-tecnico
Latin America (Argentina)
http://www.viewsonic.com/la/
http://www.viewsonic.com/la/soporte/
servicio-tecnico
Puerto Rico & Virgin Islands
http://www.viewsonic.com
Phone: [phone] (English)
http://www.viewsonic.com/la/soporte/
servicio-tecnico
3
4
i
Port connections
System setup
1. PLUG the AC power adapter into an AC outlet
→ You should see the boot up screen as shown on the right.
2. WAIT while player boots up (~ 60 seconds)
→ Once you see the “Basic settings” screen, the unit is ready for content update or
menu configuration.
3. PLUG IN a USB mouse to the unit’s USB port.
4. Enter the corresponding configuration menu by moving the mouse cursor over the
configuration and click on the option to enter
→ (Wireless model only) Using the USB mouse, click on “Wireless LAN” to enter
Wireless Configuration and provide security information to connect to your wireless
access point.
→ Find and set the correct time/date AND time zone. IMPORTANT: time zone must be
set correctly in the menus or via management software for scheduled playback.
→ (OPTIONAL) Set a Password in the menus to prevent unauthorized changes.
IMPORTANT: Password is required to enter the setup menu during playback.
5. Click Set content button to enter the content service menu and configure your
signage appliance to a content service.
NMP580-W
Network Media Player
Quick Start Guide
NMP580-W_QSG_Rev. 1a 08-21-15
Copyright © 2015 ViewSonic Corporation. All rights reserved.
HDMI
IN
Micro SD
card Audio
OUT
USB X 3
DC in
RS232
ADB Status
LED
Ethernet
Reset
button
Wireless Antenna
Post
Kensington Lock S/PDIF
HDMI
OUT
VGA