Vinsetto 920-071V70 Installation guide

ASSEMBLY & INSTRUCTION MANUAL
INcfb039V01_UK
920-071V70
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
70KG
Max 70kg

IMPORTANT SAFEGUARDS
Read these instructions carefully and retain them for future use.
When using the product, basic safety precautions should always be
followed to reduce the risk of injury including the following:
●Unpack all hardware bags and components to ensure you have all
the parts.
●Use the tools included to assemble the desk, don’t use the incorrect
tools to assemble.
●Do not climb, stand or sit on the desk.
●Do not place objects on the desk when moving.
●Check to ensure all bolts, screws and brackets are tightened on a
regular basis.
●Do not place the table in a humid environment.
●Do not place heavy objects on the table when storing.
There is potential risk of personal injury not to follow the instructions
when in use.
Input voltage 110-240(AC) V
Input AC frequency 47-63 Hz
Output voltage 29 V
Output current 1.8 A
Output power 52.2 W
Average active efficiency 88 %
Efficiency at low load (10 %) 88 %
No-load power consumption 40 W

Parts List
A
C
E
G
I
B
D
F
H
J
Lift column*1
Base*2
Side bracket*2
Desk top*4+Wooden pin*12
Power supply holder*1
Handset + Power supply
Power cord
M6 screws*52
L
Tapping screws*4
K
M4 screws*1
N
5# wrench*1
crossscrewdriver*1
Lift column*1
Frame*2
Motor Rod*1
Desktop connection block*4
G1G
2
N
1
J K LI 1I 2I 3
DX2
1
DX2
2
①
②
④
③
N2

Assembly steps
Step 1:
1.1 Connect the ①board and the ②board with wooden pins. Then connect ③ and ④to the ①and
② tables with wooden pins.
1.2 Fasten connecting blocks with M6 screws as shown in the figure.M6 screws using the
supplied spanner .
1.3 The hand controller is fastened to the table with self-tapping screws.Self-tapping screws
using the supplied screwdriver .
1.4 After installing the power supply holder, set aside.
H
J
N 1
L
N
2
G 2
N
2
N
1
Step 2:
Fixing lift column and lift column to the table leg with M6 screws.M6 screws using the supplied
spanner .
A B J
N
1
N
1
prohibited remove
JH
I 1
L
1
2
4
3
G 2
G 1
2
1
1
2
3
4
J
C
A
B

Step 3:
3.1 Assembling frame tightened with M6 screws.M6 screws using the supplied spanner .
3.2 Then install the two side bracket with M6 screws.M6 screws using the supplied spanner .
J
N 1
J
N 1
Step 4:
4.1 Lay the table board flat and put it on the table shelf.
4.2 Attach M6 screws on the middle crossbar, but not taghten them frstly.M6 screws using
the supplied spanner .
4.3 Align the screw holes on both sides of the frame and lock the M6 screws.M6 screws using
the supplied spanner .
J
N 1
N 1
N
1
N
1
J
Same side
Notice: please preload all the
screws into the holes first and
then fasten them up.
JE
J
D2
D1
D1
D2

Step 5:
6.1 As shown in Figure 1, insert the hexagonal bar into the table leg B until the buckle is not
visible.
6.2 Assemble the other end of the connecting rod to the table leg A and screw on the handle.
The handle does not need to be tightened.
Note: As shown in Figure 2 below, it needs to be aligned with the card slot.
6.3 Pull the connecting rod with the handle to the bottom end of the table leg A in the direction
of the arrow as follows.
6.4 Tighten the handle and install the M4 screws.M4 screws using the supplied screwdriver .
6.5 Conect the power cord and motor of the power supply handest as show in the figure.
KN
2
I3I2I1
N
2
Tightened
1
2
3
K
I3
I2
I1

Operational instructions
1. Lift Column
Press the button or button to control the lift column up or down Press the button to control
up of the lifting column, you can see the height (displayed number) on the screen; press the
button to control the down of the lifting column, you can see the height (displayed number) on
the screen.
2. Set memory height
Press( ) button for 2 seconds, set the current height to the memory height, When flashing
display "H1~H4"2 seconds, after 2 seconds display real-time height.
3. call memory height
Press the number button ( ) can call its corresponding height, lift column will automatically
run to the right position.
4. stroke reset
"E10、E20" alarm state or running to the lowest height position, press the button 3 seconds,
after the display ( Reset) is released, the lifting column starts to run down to the bottom of
the frame and rebound to a certain height, the reset is completed to display the lowest height.
5. protection and alarm
1.Block Protection: Display "E02." During the movement of the desk top vibration, collision or
tilt desktop, which will alarm and immediately stop, reverse motion set the distance after
automatic release, or in the reverse run press any key to stop and release. should be checked
and ensured that the table does not vibrate substantially during operation, hit an obstacle or
occur a tilt re-run.
2.Overheating protection: Display "Hot ." Continuous operating may initiate this protection
and should be recharged or waited for at least 18 minutes before use.
3.Motor abnormal protection: Display "E10." Should be power off, re-check and ensure that
the connection of the motor to the controller is reliable and then reconnect.
4.Overload protection: Display "E20." This alarm should be removed from the desk top when
it’s operating up; if this alarm occurs when it’s operating down, cut off the power and the
heavy objects should be removed, and the power should be re-charged.
5.Under-voltage protection: Display "E31." Should be power off, recheck and make sure the
connection between the power supply and the handset is reliable, then connect the power.
6.Over-voltage protection: Display "E32." Should be power off, recheck and make sure the
connection between the power supply and the handset is reliable, then connect the power.