Vision Fitness R2600HRT User manual

Guide
Assembly
R2600HRT
SEMI-RECUMBENT FITNESS CYCLE

semi-recumbent fitness cycle
To avoid possible damage to this Fitness Cycle, please follow these assembly steps in the correct order. Before proceeding though,
find your new Fitness Cycle’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and also enter this serial number on your Warranty Card and in your own records.
Be sure to read your Owner’s Guide before using your new Fitness Cycle.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your Fitness Cycle, to prevent
loosening and noise. Also, during each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before
completely tightening any ONE bolt.
R2600HRT
1
STEP
2
STEP
3
STEP
5
STEP
5
STEP
4
STEP

5MM Allen Wrench
Screwdriver
TOOLS & PARTS INCLUDED
PARTS BOX
Power Supply, Qty: 1
Water Bottle & Bracket, Qty: 1
Heart Rate Chest Strap, Qty: 1
Console Mast Rubber Cover, Qty: 1
Parts Bags
Owners Manual
Assembly Guide
Warranty Card
6MM Allen Wrench
5MM L-Shaped Wrench
4MM L-Shaped Wrench

GREEN BAG
HARDWARE INCLUDED
M8 x 15MM Bolt
Quantity: 4
M8 x 20L Cap Screw
Quantity: 4
M8 Lock Washer
Quantity: 4
PINK BAG
M8 x 15MM Bolt
Quantity: 4
M8 Washer
Quantity: 4
ORANGE BAG
M8 x 20MM Bolt
Quantity: 4
BLUE BAG
M8 x 60MM Bolt
Quantity: 2
M8 Lock Washer
Quantity: 2
BLACK BAG
M6 x 55MM Bolt
Quantity: 8
M6 Lock Washer
Quantity: 8

5
1
STEP
• Install the rear foot with the four
bolts (M8 X 20MM), using the Blue
5MM Allen wrench.
ORANGE BAG
1
STEP
2
STEP
• Slide the rubber cover onto the
console mast.
• Unfold the wire and attach it to the
string located inside the mast. Guide
the wire up through the mast while
simultaneously sliding the mast onto
the frame bracket.
• Bolt the mast to the frame with the
two bolts (M8 x 60MM) and two lock
washers (M8) using the 5MM Allen
wrench. Make sure these are tight!
• Slide the rubber cover down over
the bolt heads.
• Attach the waterbottle cage to the
console mast using the two included
screws.
BLUE BAG
2
STEP

6
3
STEP
• Mount the upper handlebars to the
console mast using the four bolts
(M8 X 15MM) and four washers (M8)
using the 5MM Allen wrench.
PINK BAG 3
STEP
4
STEP
• Remove the four screws from
the back of the console. Plug the wire
connector from inside the mast into
the console. The cable connector is
slotted, so it may only be connected
one way; do not force it!
• Mount the console to the mast using
the four screws. Do not pinch the
cable!
CONSOLE
4
STEP

7
5
STEP
Wires A
Wires B
5
STEP
• Attach the seat frame onto the
seat bracket, using 4 cap screws
(M8x20L). Tighten with the 6MM Allen
Wrench.
• Connect Wires A on the seat
handlebar to Wires B on the seat
bracket. Attach the seat handlebar to
the seat bracket using 4 bolts
(M8x15L) and 4 lock washers (M8).
Tighten with the 5MM Allen Wrench.
GREEN BAG

8
621-D East Lake Street • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
2001 Vision Fitness. All Rights Reserved. 5.01 Part #Z26RB49-AG1802PRD
AG18.02PRD
REV2
6
STEP
6
STEP
• Secure the seat back and the seat
bottom to the seat frame with 8 bolts
(M6x55L) and 8 lock washers (M6).
Tighten with the 4MM L-shaped Allen
wrench.
• Attach the seat cover to the rear of
the seat back rest by snapping it in
place.
BLACK BAG