Vision Fitness E3600HRT User manual

Assembly
Guide
E3600HRT
COMMERCIAL UPRIGHT FITNESS BIKE

1
STEP
2
STEP
3
STEP 4
STEP
To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order. Before proceeding, find your
new Fitness Bike’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be
sure to read your Owner’s Guide before using your new Fitness Cycle.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Fitness Bike to prevent loosen-
ing and noise. Also, during each assembly step, ensure that ALL screws are in place and partially threaded in before completely
tightening any ONE screw.
Assembly
Guide
E3600HRT
COMMERCIAL UPRIGHT FITNESS BIKE

TOOLS & PARTS INCLUDED
5MM Allen Wrench
15MM Pedal Wrench
Screwdriver
PARTS BOX
Console Mast Cover, Qty: 1
Water Bottle & Cage, Qty: 1
Color-coded Hardware Bags
Owner’s Guide, Qty: 1
Assembly Guide, Qty: 1
Warranty Card, Qty: 1
Heart Rate Chest Strap, Qty: 1

HARDWARE INCLUDED
ORANGE BAG PINK BAG
M8 x 65L Screw
Quantity: 2
BLUE BAG
M8 x 15L Screw
Quantity: 7
M8 x 20L Screw
Quantity: 2
M8 x 20L Screw
Quantity: 2
M8 Lock Washer
Quantity: 4
M8 Lock Washer
Quantity: 6
M8 Lock Washer
Quantity: 2

5
1
STEP
• Install the rear foot with four lock
washers (M8), two inside screws
(M8x65L), and two outside screws
(M8x20L). Tighten with the 5MM Allen
wrench.
ORANGE BAG
1
STEP

6
2
STEP
• Slide the rubber boot onto the
console mast.
• Unfold the wire harness located in
the console mast frame bracket.
Connect it to the wire tie coming from
the bottom of the console mast. Pull
the wire tie and wire harness up
through the top of the console mast
while simultaneously sliding the mast
into the frame bracket.
• Secure the mast to the frame using
six lock washers (M8) and six screws
(M8x15L). Tighten with the 5MM Allen
wrench. Place the seventh screw
(M8x15L) in the rear of the frame
bracket and tighten until snug.
• Slide the rubber boot down and
snap it into place on the side cover.
• Remove the nuts (M8) from the
bottom of the seat. Attach the seat to
the seat post with the nuts you just
removed. Tighten with the 15MM
wrench.
• Loosen the seat post knob and slide
the seat post into place in the seat
tube bracket.
BLUE BAG
2
STEP

7
3
STEP
• Feed the heart rate wires of the
handlebar through the small hole
located in the front of the console
mast. Pull these wires up through the
hole at the top of the console mast.
Attach the handlebar to the console
mast using two lock washers (M8)
and two screws (M8x20L). Tighten
with the 5MM Allen wrench.
PINK BAG
3
STEP

8
500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
2002 Vision Fitness. All Rights Reserved. 8.02 Part #Z36CB39-AG1821PRD
AG18.21PRD
REV1
4
STEP
• Remove the four mounting screws
from the back of the console with the
Phillips screwdriver. Make sure the 9
Volt battery is plugged in and in place
on the back of the console. Connect
the wire harness and the two heart
rate wires to the receptacles in the
back of the console. Attach the
console to the console mast with the
four screws removed earlier in this
step.
• With the Phillips screwdriver,
remove the two screws located half
way up the console mast. Attach the
water bottle bracket to the console
mast with the two screws. Insert the
water bottle.
CONSOLE
4
STEP