Vision Fitness E4000 User manual

Assembly
Guide
E4000
DUAL-ACTION UPRIGHT FITNESS CYCLE

1
STEP
2
STEP
4
STEP
3
STEP
To avoid possible damage to this Fitness Cycle, please follow these assembly steps in the correct order. Before proceeding, find
your new Fitness Cycle’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be
sure to read your Owner’s Guide before using your new Fitness Cycle. If any parts, hardware or tools are missing, please call
1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Fitness Cycle to prevent
loosening and noise. Also, during each assembly step, ensure that ALL screws and nuts are in place and partially threaded in before
completely tightening any ONE screw.
Assembly
Guide
E4000
DUAL-ACTION UPRIGHT FITNESS CYCLE
5
STEP

5MM Allen Wrench 15MM Pedal Wrench
Screwdriver
4MM L-Shaped Wrench
TOOLS & PARTS INCLUDED
PARTS BOX
Front Axle, Qty: 1
Front Transport Wheels, Qty: 2
Arm Rail Covers, Qty: 2
Water Bottle & Bracket, Qty: 1
Owner’s Guide, Qty: 1
Assembly Guide, Qty: 1
Warranty Card, Qty: 1
Closed Wrench

BLUE BAG
ORANGE BAG
PINK BAG
HARDWARE INCLUDED
M8 x 19L Screw
Quantity: 4
M8 x 41L Screws
Quantity: 2
M5 x 12L Screw
Quantity: 1
M8 Nylock Nut
Quantity: 2
M17 Wavy Washer
Quantity: 2
M8 x30 Washer
Quantity: 2

5
1
STEP
• Slide the rear foot into place and
secure the four screws (M8 x 19L)
with the 5MM Allen wrench.
ORANGE BAG
1
STEP

6
2
STEP
• Loosen the Set Screw in the Arm
Axle with the 4MM L-shaped Wrench.
• Slide the Front Arm Axle into the
plastic sleeve of the front foot. Slide a
Wavy Washer onto each end of the
axle.
• You will now need to disassemble
part of the roller assembly on the arm
crank. Please remove the Nylock Nut
(M8), the Washer (M8 x 17), the
Tension Spring, the Washer (M13),
and the Outside Roller. Repeat this
step on the left side.
• Slide the Right Arm onto the right
arm axle and the right arm crank.
Reinstall the Outside Roller, the
Washer (M13), the Tension Spring,
the Washer (M8x17), and the Nylock
Nut (M13). Repeat this step on the left
side
• Attach the Right Arm Cover to the
right arm. It should snap into place.
Repeat this step on the left side.
• Install the Right Mobile Wheel, the
Washer (M8x30), and the Nylock
Nut (M8) to each end of the axle.
Tighten with the closed wrench.
Repeat this step on the left side.
• Tighten the Set Screw in the Arm
Axle with the 4MM L-shaped Wrench.
BLUE BAG
2
STEP

7
3
STEP
• Remove the three screws from the
upper cover of the bike frame.
• Slide the upper cover onto the
console mast.
• Attach the included string to the
Sensor Wire and pull the Sensor Wire
up through the console mast. Slide the
tension control wire up through the
console mast.
• Slide the console mast onto the
frame bracket and fix it in place with
two screws (M8 x 41L) and the
5MM Allen wrench.
• Install the batteries into the console.
Plug the Sensor Wire into the
Console. Attach the Console with the
included screws.
• Turn the tension knob to Level 15.
Reach inside the mast and connect the
tension control cables. Turn the knob
to Level 1 and mount the knob to the
mast with the screw (M5 x 12L).
• Slide the Upper Cover into place
and secure it to the frame using the
two screws for the front and one
screw for the back of the cover.
(These are the screws you removed in
the first step)
PINK BAG
3
STEP
4
STEP
• Place the seat on the seat post and
tighten with a 13MM wrench.
SEAT
4
STEP

8
500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
2002 Vision Fitness. All Rights Reserved. 8.02 Part #Z40CB29-AG1807PRD
AG18.07PRD
REV2
5
STEP
• Attach the left and right pedals to
the left and right crank arms. Tighten
using the 15MM Pedal wrench.
• Slide the foam grips onto the dual-
action arms. NOTE: It is best to spray
a lubricant such as Armor-All into the
foam grip to help with this step.
BLACK BAG
5
STEP