Vision Fitness T9200 DELUXE User manual

ENGINEERING GUIDES
1
Date of last revision: 2.06
TREADMILL.UPPERBDENG.DELUXE.REV1
STANDARD CONSOLE FOR:
(T9200 DELUXE, T9500 DELUXE, T9600 DELUXE, T9250 DELUXE, T9450 DELUXE)
DELUXE (6-WINDOW) UPPER BOARD
ENGINEERING GUIDE

ENGINEERING GUIDES
Date of last revision: 2.06 TREADMILL.UPPERBDENG.DELUXE.REV1
2
ENGINEERING MODE
The user must hold down “ELEVATION UP” and “SPEED DOWN” for 5 seconds after powering up the treadmill to
enter the engineering menus. The P6 menu appears with the software version in the upper right window along with
the model number in the upper left window. Press
“STOP” to exit P6. The user has 6 engineering modes to choose
from. The
“SPEED” and “ELEVATION” keys scroll through the modes, while “SELECT” chooses the mode. HOLDING
the
“SELECT” button saves information and the “STOP” button goes back to the previous screen. When in
Engineering modes 1-5, holding down the
“STOP” button for 5 seconds will return you to the Engineering Mode
Selection Screen.
Display Engineering Mode
Eng 1- Configure Mode Edits variables stored in the NOVRAM. Speed and Incline variables
can be edited in this mode.
Eng 2- Display and Key Test Tests displays and keyboard
Eng 3- Burn In Mode Runs continuous program
Eng 4- Auto Calibration Mode Calibrates both speed and elevation
Eng 5- Speed Sensor Test Tests speed sensor functionality
Eng 6- Exit Exit engineering mode
ENG1: EDIT VARIABLES MODE
The display shows the P address. To choose the P address press “SELECT” .
To clear P9 total time press and hold
“START” for 3 seconds
To clear P10 total distance press and hold
“START” for 3 seconds
T9200/T9250/T9450 VARIABLES
Address Description Default Value Min.Value MaxValue
P0 Minimum Speed Data N/A 310 600
SP1 Speed Data 2 N/A 700 1100
P1 1/2 max Speed Data N/A 1400 2100
SP2 Speed Data 4 N/A 2000 3000
P2 Max speed Data N/A 3200 4500
P3 LED Brightness 3 0 9
P4 Minimum Elevation Data N/A 30 300
P5 Max Elevation Data N/A 650 900
P6 Model and Unit (Metric/US) N/A N/A N/A
P7 Max Time 99 15 99
P8 Default Weight 150 80 400
P9 Accumulated Time N/A N/A N/A
P10 Accumulated Distance N/A N/A N/A
P11 Belt Thickness (depending on model) 16 44
P12 Roller Diameter 60 60 60
P13 Elevation motor 1
P14 Pause Time 5:00 :20 10:00
P15 Default Time 30 1 99
P16 Default Age 40 5 120
P17 Exit Mode (Exits Eng 1)
Deluxe Upper Board: Engineering Guide

ENGINEERING GUIDES
Date of last revision: 2.06TREADMILL.UPPERBDENG.DELUXE.REV1
3
T9500/T9600 VARIABLES
Address Description Default Value Min.Value MaxValue
P0 Minimum Speed Data N/A 310 600
SP1 Speed Data 2 N/A 700 1400
P1 1/2 max Speed Data N/A 2000 3200
SP2 Speed Data 4 N/A 3000 4200
P2 Max speed Data N/A 3900 5200
P3 LED Brightness 3 0 9
P4 Minimum Elevation Data 250 30 300
P5 Max Elevation Data 850 650 900
P6 Model and Unit (Metric/US) N/A N/A N/A
P7 Max Time 99 15 99
P8 Default Weight 150 80 400
P9 Accumulated Time N/A N/A N/A
P10 Accumulated Distance N/A N/A N/A
P11 Belt Thickness (depending on model) 16 44
P12 Roller Diameter 60 60 60
P13 Elevation motor 1 N/A N/A
P14 Pause Time 5:00 :20 10:00
P15 Default Time 30 1 99
P16 Default Age 40 5 120
P17 Exit Mode (Exits Eng 1)
CONFIGURATIONS
Modify the units by pressing the speed arrows to select MI or KM. Modify the model by pressing the elevation arrows.
Press and hold
“SELECT” to save.
Deluxe Upper Board: Engineering Guide
T9250
0-12% elevation
0.5-10 mph/ 0.8-16kph
T9450
0-12% elevation
0.5-10 mph/ 0.8-16kph
T9200
0-12% elevation
0.5-10 mph/ 0.8-16kph
T9500
0-12% elevation
0.5-12 mph/ 0.8-20 kph
T9600
0-15% elevation
0.5-12 mph/ 0.8-20 kph

ENGINEERING GUIDES
Date of last revision: 2.06 TREADMILL.UPPERBDENG.DELUXE.REV1
4
ENG2: DISPLAY TEST MODE
Key Function
ENTER/ SELECT All LEDs light up
SPEED UP Turns on individual LEDs in all the displays in a clockwise motion and the dots in the dot
matrix move up in different colors
SPEED DOWN Turns on individual LEDs in all the displays in a counter-clockwise motion and the dots in the
dot matrix move down in different colors
STOP No Function
ELEVATION UP Shifts 8 across the seven segment display and a column in the dot matrix from Left to Right
ELEVATION DOWN Shifts 8 across the seven segment display and a column in the dot matrix from Right to Left
START Turns on the Function LEDs one at a time. Continue to press START to test each LED.
ELEVATION 1-9 Displays Elevation number in the LED windows
SPEED 1-9 Displays Speed number in the LED windows
ENG 3: BURN IN MODE
The burn in mode can be used to run tests that require the treadmill to continually run. The program is based on the
5k program. Segment changes will occur, depending on the treadmill configuration. When the system reaches the last
segment, it loops to the first segment. Speed start is at half max. The user can adjust the speed and incline. The program
returns to the preset incline upon segment completion. Keyboard functions are the same as in normal operating mode.
ENG 4: AUTO-CALIBRATION
1. Check configuration in ENG 1 before auto-calibrating treadmill.
2. Press the
“SELECT” key once. ““AAUUTTOO--CCAALLIIBBRRAATTEE””will scroll in the dot matrix.
3. Press “START” key once to begin Auto-Calibration
4. The treadmill software will look where the elevation stalls to determine the minimum elevation. The software
then automatically backs off to set 0% elevation. The software will then look where the elevation stalls for the
highest point the treadmill elevation will go. The software will automatically back off and set the maximum
elevation, 12% or 15% depending on the treadmill model. Meanwhile the belt is being driven while the
speed is being monitored. As it reaches the minimum, speed 1, 1/2 max, speed 2 and max speed the PWM
is recorded for these targets. The Elevation window displays the Elevation A/D and the number in the upper
right window displays the speed PWM.
6. To look at these numbers after calibration go into engineering mode and go to ENG1; press
“SELECT” .
7. In P0, SP, P1, SP2, P2 the speed will be displayed. Press
“SELECT” to read the PWM value.
P4 and P5 represent the elevation values
Deluxe Upper Board: Engineering Guide

ENGINEERING GUIDES
Date of last revision: 2.06TREADMILL.UPPERBDENG.DELUXE.REV1
5
ENG 5: SPEED SENSOR MODE
The PWM value is displayed in the upper right window. The Elevation A/D is displayed in the upper left window.
The Dot Matrix displays a flashing row of lights between 2 constant rows of lights. As the
“SPEED UP” arrow is
pressed the flashing row will flash quicker, indicating a faster PWM.
ENG 6: EXIT ENGINEERING
ERROR MESSAGES
Three types of errors can occur; speed, elevation, and EEPROM software error. All three use the same display to indicate
the error, with the error number appearing in the main window. An elevation error shuts down the treadmill and disables
normal operation. A speed sensor error also shuts down the treadmill. The user, however, can enter engineering mode
after an error announcement.
Deluxe Upper Board: Engineering Guide
ERROR DISPLAY DESCRIPTION SOLUTION
SAFETY SWITCH
If the safety magnet disconnects from the console, the treadmill shuts down if in run mode. The treadmill displays ““--------““in
the main window. This is a safety precaution to warn the user that power is still being applied to the board. This safety
switch condition occurs in any mode, including engineering modes.
When the magnet reconnects to the console, the board resets. Any activity or run time information prior to the reconnection
will be lost.
Elevation
Range
Elevation
Stall
Elevation
Lost
Over speed
No Speed
Feedback
E4
E4
E6
E7
E9
Current elevation position is outside
zero and max elevation values
Current elevation position has not
reached target incline
No elevation signal reading or elevation
motor is not connected.
Speed of the belt differs from the
calibrated max speed by 1.0 mph or
km/h as measured by the speed sensor
No speed is detected during
Auto-Calibration
Enter ENG 1 and manually position elevation within
the min and max values. If not possible, recalibrate
min and max elevation
Check for bad cable connection. Check for connection
between motor controller and elevation motor as well
as any obstruction to the elevation. Try to reboot system
Check for bad cable connection. Check for connection
between motor controller and elevation motor. Check
for bad elevation motor
Cycle power to clear error. Check speed sensor and
magnets as well as any obstruction to the rollers or
running belt. Recalibrate.
Check speed sensor cable, speed sensor and magnets

ENGINEERING GUIDES
Date of last revision: 2.06 TREADMILL.UPPERBDENG.DELUXE.REV1
6
USER ENGINEERING MODE (DELUXE ONLY)
Your treadmill offers a User Engineering Mode that can access certain data and help to troubleshoot your treadmill.
User Engineering Mode is designed for you to access functions that will not affect important treadmill settings. To
access this mode please hold down
“SPEED DOWN” and “SELECT” for 5 seconds while the treadmill is in any state
of setting up a program. When in the User mode, ""UUSSEE""is displayed. To access the data press the
“SPEED” and
“ELEVATION” keys to scroll through the available data/functions. To select the data/function, press “SELECT” . To
exit, press
“STOP” . The units screen will appear when entering user engineering. If the units are correct press “STOP” .
UNITS
P6 represents units, English or Metric. You can select this configuration for your Treadmill.
““MMII””or ““KKMM””appears in the dot matrix. If it is ““MMII””, the Treadmill is configured in English units (miles/mph); ““KKMM””represents
a Metric configuration (kilometers/kph). Press the
“SPEED” arrows to toggle between English and Metric.
In order to save the modified value, press and hold
“SELECT” . Note that changing units does affect the stored value
of weight and clears any stored user programs. Changing units may also require you to perform auto-calibration.
MAX TIME
P7 represents the maximum time, which is displayed in the upper right window. This is the maximum amount of time
the Treadmill will display. You can modify this time by using the
“SPEED” or “ELEVATION” arrows. Press and hold
“SELECT” to save the new value.
DEFAULT WEIGHT
P8 represents default weight. Weight appears in the upper left window. To modify weight, press the “SPEED” arrows.
To save the new default weight, press and hold
“SELECT” prior to exiting. If Units is modified immediately prior, weight
defaults to 150 lbs. or 68 kg.
ACCUMULATED TIME
P9 represents accumulated time, in hours. To exit, press “STOP” . This information can not be modified.
ACCUMULATED DISTANCE
P10 represents accumulated distance, in either miles or kilometers. To exit, press “STOP” . This information can not
be modified.
PAUSE TIME
P14 represents the pause time, which is displayed in the upper right window. The default pause time is 5 minutes.
You can modify the pause time from 20 seconds to 10 minutes. You can modify this time by using the
“SPEED” or
“ELEVATION” arrows. Press and hold “SELECT” to save the new value.
DEFAULT TIME
P15 represents the program default time, which is displayed in the upper right window. Most programs have a default
time of 30 minutes. You can modify this time by using the
“SPEED” or “ELEVATION” arrows. Press and hold
“SELECT” to save the new value.
Deluxe Upper Board: Engineering Guide

ENGINEERING GUIDES
Date of last revision: 2.06TREADMILL.UPPERBDENG.DELUXE.REV1
7
DEFAULT AGE
P16 represents the default age, which is displayed in the upper left window. The Treadmill comes with the default age
of 40. You can modify the age by using the
“SPEED” or “ELEVATION” arrows. Press and hold “SELECT” to save
the new value.
AUTO-CALIBRATION
DO NOT STAND ON THE BELT WHEN PERFORMING THE AUTO-CALIBRATION!
Auto-calibration is not represented by a Px designation. ""AAUUTTOO""appears in the center window. When you enter the
function, ""AAUUTTOO""begins flashing. To begin auto-calibration, press
“START” . The treadmill will run through minimum and
maximum speed and maximum incline, this will take three to five minutes. Let the treadmill perform this complete function
before exiting the Engineering Mode.
Elevation A/D or Elevation in % appears in the left window. PWM value or Speed appears in the right window.
""EE""will appear in the center window when the auto-calibration is complete. When auto-calibration is complete, it
will take about 30 seconds to return to the start-up screen with ““PP11””showing in the function window.
EXIT USER ENGINEERING MODE
P17 represents exit mode. When you press “SELECT” to select the function, the console performs a reboot, returning
to program setup.
Deluxe Upper Board: Engineering Guide