Vision Fitness T9250 User manual

Guide
Assembly
T9250, T9350, T9450HRT
FOLDING TREADMILLS

folding treadmills
To avoid possible damage to this Folding Treadmill, please follow these assembly steps in the correct order. Before proceeding
though, find your new Folding Treadmill’s serial number, located on the underside of the main frame, and enter here:
Refer to this number when calling for service, and also enter this serial number on your Warranty Card and in your own records.
Be sure to read your Owner’s Guide before using your new Folding Treadmill.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your Folding Treadmill, to prevent
loosening and noise. Also, during each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before
completely tightening any ONE bolt.
T9450HRTT9250 T9350
1
STEP
2
STEP
3
STEP
4
STEP

5MM Allen Wrench
Screwdriver
TOOLS, HARDWARE, & PARTS INCLUDED
PARTS BOX
Water Bottle, Qty: 1
Optional Heart Rate Chest Strap, Qty: 1
(T9450HRT only)
Color-coded Hardware Bags
Owner’s Guide
Assembly Guide
Warranty Card
8MM Allen Wrench

ORANGE BAG
BLUE BAG
PINK BAG
M8 x 50L Bolts
Quantity: 4
TOOLS, HARDWARE, & PARTS INCLUDED
M8 x 20L Bolts
Quantity: 2
M4 x 12L V-head Screw
Quantity: 2
M8 x 135L Bolts
Quantity: 4
M8 x 20L Flathead Bolts
Quantity: 4
M4 x 12L V-head Flat Screw
Quantity: 4

5
1
STEP
2
STEP
1
STEP
• Fold up the right-hand console mast
to the vertical position. Be sure not to
pinch the data cables.
• Insert the bolt (M8 x 50L) in the side
and tighten with the blue-handled 5MM
Allen Wrench.
• Insert one bolt (M8 x 20L) in the front
and tighten with the blue-handled
5MM Allen Wrench.
• Repeat this on the opposite side.
NOTE: There are no data cables on
the left side.
ORANGE BAG
2
STEP
• Slide the base side covers down the
left-hand and right-hand console
masts.
• Fold the treadmill to the vertical
position.
• Secure the right-hand base side
cover to the base frame. Use the
V-head screw (M4 x 12L) for the rear
of the cover and the Flat screws
(M4 x 12L) for the front of the cover.
Repeat this step on the left side.
• Unfold the treadmill.
BLUE BAG

6
3
STEP
3
STEP
• Mount the right-hand side mount
handlebars to the console mast using
two bolts (M8 x 135L). Repeat this on
the left-hand side.
• Plug in the large data cable into the
large plug connection in the connection
box on the right-hand side of the console.
• Plug in the small data cable into the
small plug connection in the connection
box on the right-hand side of the
console
NOTE: Push all extra data cable into
the console mast. Make sure not to
pinch or cut the data cable.
• Mount the console to the console
masts using four bolts (M8 x 20L)
and tighten with the blue-handled
5MM Allen wrench.
PINK BAG

7
4
STEP
• If the running belt slips when used,
use the supplied 8MM Allen wrench to
turn the left and right tension bolts
clockwise 1 /4-turn at a time until the
belt no longer slips.
• If the running belt is too far to the
right side, use the supplied 8MM Allen
wrench to turn the right tension bolt
clockwise 1 /4-turn at a time until the
belt remains centered during use.
If the running belt is too far to the left
side, turn the left tension bolt
clockwise 1 /4-turn at a time until the
belt remains centered during use.
BELT TENSION
500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
2001 Vision Fitness. All Rights Reserved. 11.01 Part #Z92TM43-AG1810PRD
AG18.10PRD
REV2
4
STEP