Vision Fitness T9250 User manual

Assembly
Guide
T9250 AND T9450
FOLDING TREADMILLS

30:00
0
1
STEP
2
STEP
6
STEP
To avoid possible damage to this Folding Treadmill, please follow these assembly steps in the correct order. Before proceeding
though, find your new Folding Treadmill’s 2 serial numbers, located on the underside of the main frame and on the bottom of the
console, and enter here:
Refer to these numbers when calling for service, and also enter these serial numbers on your Warranty Card and in your own
records. Be sure to read your Owner’s Guide before using your new Folding Treadmill.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your Folding Treadmill, to prevent loos-
ening and noise. Also, during each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before
completely tightening any ONE bolt.
Assembly
Guide
T9250 AND T9450
FOLDING TREADMILLS
3
STEP
4
STEP
Frame Serial Number Console Serial Number

5mm Allen Wrench
Screwdriver
TOOLS, HARDWARE, & PARTS INCLUDED
PARTS BOX
Water Bottle, Qty: 1
Safety Magnet Key, Qty: 1
Color-coded Hardware Bags
8mm Allen Wrench

HARDWARE INCLUDED
ORANGE BAG
BLUE BAG
PINK BAG
M8 x 20L Bolts
Quantity: 8
Flathead pointed screw
Quantity: 2
M8 x 135L Bolts
Quantity: 4
M8 x 20L Bolts
Quantity: 4
Flathead screw
Quantity: 4

5
1
STEP
2
STEP
1
STEP
• Slide on the right and left console
mast covers from the bottom of the
console masts
• Using the wire tie as a guide, slide
the data cables (One small and one
large) up from the bottom of the right
console mast. Make sure the data
cables run through the slot located at
the front of the right console mast.
• Put the console mast into the
console mast bracket. Be sure not to
pinch the data cables
• Secure the console mast to the
bracket with 4 bolts (M8x20L); 2 bolts
on each side. Tighten with the
enclosed 5mm Allen wrench
• Repeat on the left side
NOTE: There are no data cables on
the left side.
ORANGE BAG
2
STEP
• Slide the left and right console mast
covers over the console mast brackets.
• Fold the treadmill
• Attach the right side cover using the
Flathead pointed screws for the rear
of the cover and the Flathead screws
for the front of the cover.
• Repeat this step on the left side.
• Unfold the treadmill
BLUE BAG

6
30:00
0
3
STEP
4
STEP
3
STEP
• Plug the large data cable into the
large connector on the console. Plug
the small data cable into the small
connector on the console.
• Push the extra data cable into the
console mast. Be sure not to pinch the
data cables.
• Mount the console to the console
masts. Attach the console using four
bolts (M8x20L) and tighten using the
enclosed 5mm Allen wrench.
• Attach one handlebar to the right
console mast using two bolts
(M8x135L).
• Repeat on the left side
PINK BAG
4
STEP
Once your treadmill has been
positioned for use, you should lock the
four transport wheels located on the
lower folding frame. With your foot,
simply press down on the bottom
latch, labeled ON, of all four
transport wheels.
LOCK WHEELS

7
5
STEP
Once the Treadmill is plugged in, you need to configure the Treadmill and perform auto-calibration for maximum performance.
PREMIER and DELUXE CONSOLE:
DO NOT STAND ON THE BELT WHEN PERFORMING THE AUTO-CALIBRATION
Once the treadmill is plugged in, you will need to configure and run auto-calibration. With the safety key in place, turn the
treadmill on. A setup screen should appear on the console. Set your treadmill to the correct model number (9250 or 9450)
using the ELEVATION arrow keys and the correct units (MI [miles]/KM [kilometers]) using the SPEED arrow keys. If you are
unsure of the model number, you can locate the number on the console masts. Once you have located the model number and
units with the arrow keys, press and hold SELECT. Now you can perform auto-calibration by pressing START.
The treadmill will run through minimum and maximum speed and elevation. This will take 3 to 5 minutes. Let the treadmill per-
form this complete function. “END” will appear when auto-calibration is complete. When auto-calibration is complete, it will
take about 30 seconds for the treadmill to reboot and return to the start-up screen.
SIMPLE CONSOLE:
DO NOT STAND ON THE BELT WHEN PERFORMING THE AUTO-CALIBRATION
Once the treadmill is plugged in, you will need to configure and run auto-calibration. With the safety key in place, turn the
treadmill on. A setup screen should appear on the console. The large LED window displays the model number and the small
LED window displays the units. Set your treadmill to the correct model number (9250 or 9450) using the ELEVATION arrow
keys and the correct units (0 for miles and 1 for kilometers) using the SPEED arrow keys. If you are unsure of the model num-
ber, you can locate the number on the console masts. Once you have located the model number and units with the arrow
keys, press and hold SELECT. Now you can perform auto-calibration by pressing START.
The treadmill will run through minimum and maximum speed and elevation. This will take 3 to 5 minutes. Let the treadmill
perform this complete function. “END” will appear in the window when auto-calibration is complete. When auto-calibration
is complete, it will take about 30 seconds for the treadmill to reboot and return to the start-up screen.
MODEL CONFIGURATION & AUTO-CALIBRATION

8
500 South CP Avenue • P.O. Box 280 • Lake Mills, WI 53551
toll free 800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
©2005 Vision Fitness. All Rights Reserved. 9.05
AG18.31PRD
REV6
6
STEP
6
STEP
• If the running belt slips when used,
use the supplied 8mm Allen wrench to
turn the left and right tension bolts
clockwise 1 /4-turn at a time until the
belt no longer slips.
• Run the treadmill at 2.0 mph. If the
running belt is too far to the right side,
use the supplied 8mm Allen wrench to
turn the right tension bolt clockwise
1
/4-turn at a time until the belt remains
centered during use.If the running belt
is too far to the left side, turn the left
tension bolt clockwise 1 /4-turn at a
time until the belt remains centered
during use.
BELT TENSION