Vision VPD200PM2Ti Manual

Page 1 / 16
HARDWARE INSTALLATION GUIDE
VPD200SM2Ti / VPD200PM2Ti FULL HD NETWORK PTZ Camera
Version 1. 0. 3
Released on 1st of June., 2013

Page 2 / 16
By selecting this product, you have decided to use a professional device that guarantees highest quality and
reliability. We would like to thank you very much for your confidence and kindly ask you to read the following
instructions carefully before installation and operation in order to take full advantage of all quality features
regarding this product.
The lighting flash with an arrowhead symbol, within an equilateral triangle is intended to alert
the user to the presence of non-insulated dangerous voltage within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
INFORMATION
This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at its own
expense.
WARNING
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to
operate the equipment.
CAUTION – To prevent electric shock and risk of the fire hazards
-Do NOT use power source other than that specified.
-Do NOT expose this appliance to rain or moisture.
Trademarks
All names used in this manual for hardware and software are probably registered trademarks of respective
companies.
This installation should be made by a qualified service person and should conform to all local codes.

Page 3 / 16
Table of content
Hardware Installation Guide
1. Precautions ---------------------------------------------------------------------------------------------------- 4
2. Limitation of liability ---------------------------------------------------------------------------------------- 4
3. Disclaimer of warranty ------------------------------------------------------------------------------------- 4
4. Package Contents --------------------------------------------------------------------------------------------- 5
5. Cable Connection --------------------------------------------------------------------------------------------- 6
6. Installation ----------------------------------------------------------------------------------------------7~13
7. Dimension (mm) ----------------------------------------------------------------------------------------------- 14
8. Specification ----------------------------------------------------------------------------------------------------- 14
VPD200SM2Ti ------------------------------------------------------------------------------------------- 15
VPD200PM2Ti ------------------------------------------------------------------------------------------- 16

Page 4 / 16
1. Precautions
l Please read the manual carefully before the installation in order to set up the camera correctly and to
obtain the best picture quality.
l Please keep the manual in good condition for your future reference and service application.
l Installation and services should be only carried out by an authorized personnel according to local safety
regulations.
l If any liquid or solid matter gets into the housing, immediately disconnect the camera from power supply
and have it checked by your authorized dealer before reusing.
l Avoid installing the camera at extremely hot or cold places.
l If you are not a certified person, never try to dismantle the camera. To avoid electric shock, never remove
the screws or covers. There are no parts inside that need maintenance by the user. All maintenance should
be carried out by qualified personnel.
l Avoid installing the camera at a place of high humidity.
l Avoid installing the camera at the place exposed to gas or oil.
l Keep the top glass of the lens always clean in order to obtain the best picture quality all the time. Be
careful not to be stained by fingerprint.
l Don't face the camera directly toward sunlight or sunlight reflecting area. Sensor may go defective at this
condition.
l Please give a special attention to keep the unit from dangerous drop or external shock during the process
of transportation or handling.
l Never try to touch the camera in wet hand. It may cause an electric shock.
l Do not expose the camera to radioactivity. It causes a serious damage on the Sensor.
2. Limitation of liability
This publication is provided “AS IS” without warranty of any kind, either express or implied, including but not
limited to, the implied warranties of merchantability, fitness for any particular purpose, or non-infringement of
the third party's right. This publication could include technical inaccuracies or typographical errors. Changes
are added to the information herein, at any time, for the improvements of this publication and/or the
corresponding product(s).
3. Disclaimer of warranty
In no event shall seller be liable to any party or any person, except for replacement or reasonable maintenance
of the product, for the cases, including but not limited to below:
(1) Any damage and loss, including without limitation, direct or indirect, special, consequential or exemplary,
arising out of or relating to the product;

Page 5 / 16
(2) Personal injury or any damage caused by inappropriate use or negligent operation of the user;
(3) Unauthorized disassemble, repair or modification of the product by the user;
(4) Inconvenience or any loss arising when images are not displayed, due to any reason or cause including any
failure or problem of the product;
(5) Any problem, consequential inconvenience, or loss or damage, arising out of the system combined by the
devices of third party.
(6) Any claim or action for damages, brought by any person or organization being photogenic subject, due to
violation of privacy with the result of that surveillance-camera's picture, including saved data, for some
reason, becomes public or is used for the purpose other than surveillance.
4. Package Contents
Note: Mount Brackets are optional.
l Wall Mount Bracket l Ceiling Mount Bracket
[Screws : Torx Secrew M4´18, Hex Lag #14´50] [Screws : Torx Screw M4´18, Anchor Bolt 3/8"´70]
l Main body & Dome Cover l Accessories
[Main Cable, Wrench, Cross LAN cable, Audio cable, CD]

Page 6 / 16
5. Cable Connection
• Dome Cover Do not detach protection vinyl from dome cover before finishing all
installation process to protect dome cover from scratches or dust.
• DIP Switch Sets up camera ID and protocol.
• Drop Prevention
Spring
This part keeps the camera from dropping during installation and
maintenance. After install the Bracket, please, hang the spring to
the drop prevention hook of main body as shown in picture for
further tasks.
• Mounting Screw
Hole
This hole is for screws that assembles the main body with a
bracket.
• IP Reset Switch Reset its network configuration to the factory defaults. You will lose
all data that had been entered previously. To initialize the system
to the factory default, press the reset button for more than 5
seconds.
• LAN Port Used for the Ethernet connection
• Audio Port Used for the audio in/out connection.
• Video (BNC) Used for the composite video out or HD-SDI video out connection
according to models
• Main Connector Used for the power wire, the RS-485 communication cable, alarm
in/out connection cable according to models.

Page 7 / 16
6. Installation
DIP Switch Setup
When you control the camera through RS-485, before installation, you should set the DIP switches to
configure the camera ID, communication protocol.
Camera ID setup
ON
ON
1 2 3 4 5 6 7 8
l ID numbers of camera are set up with binary numbers..
See the examples shown below
Pin 1 2 3 4 5 6 7 8
ID Value 1 2 4 8 16
32
64
128
ex) ID=5 on
off
On
off
off
off
off
off
ex) ID=10 off
on
Off
on
off
off
off
off
l The camera ID range is 1~255. Camera ID must not be 0.
l Factory default of Camera ID is 1.
l Match the camera ID with Cam ID setting of your DVR or Controller
to control the camera.

Page 8 / 16
Communication Protocol Setup
1 2 3 4
ON
ON
l
Select the appropriate Protocol with DIP switch combination.
Switch State
Protocol/Baud rate
P0
(Pin 1)
P1
(Pin 2)
P2
(Pin 3)
OFF
OFF
OFF
PELCO
-
D, 2400 bps
ON
OFF
OFF
PELCO
-
D, 9600 bps
OFF
ON
OFF
PELCO
-
P, 4800 bps
ON
ON
OFF
PELCO
-
P, 9600 bps
Otherwise
Reserved
l If you want to control using DVR or P/T controller, their protocol must
be identical to camera. Otherwise, you can not control the camera.
l Adjust the DIP switch after turning off the camera. If you changed the
camera protocol by changing the DIP switch, the change will be effective
after you reboot the camera.
l Factory default of protocol is “Pelco-D, 2400 bps”.

Page 9 / 16
Installation Camera with Brackets
Installation using Ceiling Mount Bracket
① Remove the ceiling tile from the ceiling and
cut a hole whose diameter is 30~40mm on the
ceiling tile to pass the wire(s) and cable(s)
through to the upside of the ceiling. (In case of
the wiring and cabling through the mounting
surface only) Then prepare the ceiling mount
bracket. Pull the wire(s) for the system as below.
(Anchor Bolt 3/8"×70)
② Hook up “Drop Prevention Spring” on main
body to prevent camera from unexpected drop and
pull the wire(s) and cable(s) for the system as
below
③ Line up the mold lines and assemble main
body to mount adaptor and turn it. And
assemble the main both with the camera
mount adaptor with the screws. (Torx screw
M4X18). Please make sure the screws are
tightly assembled for waterproof.
④ Screw the dome cover to the main body and
remove the protection vinyl from the dome
cover.
Notice
l Before starting the installation, make sure that the Camera ID and Protocol are set up properly.
l To adjust the installation height from the mounting surface, the pipe and coupler should be
needed between the surface mount part of the ceiling mount bracket and the camera mount part
of the ceiling mount bracket. Note that they are not supplied by the manufacturer.
Spring Wire Hook
END START

Page 10 / 16
Installation using Wall Mount Bracket
① Make a hole whose diameter is 30~40mm on
the mounting surface to pass the wire(s) and
cable(s) through the mounting surface. (In case of
the wiring and cabling through the mounting
surface only) Then prepare the wall mount
bracket. Pull the wire(s) and cable(s) for the
system as below. Attach the wall mount bracket to
the mounting surface. (Hex Lag #14×50)
② Hook up “Drop Prevention Spring” on main
body to prevent camera from unexpected
drop and pull the wire(s) and cable(s) for the
system as below.
③ Line up the mold lines and assemble main body to
mount adaptor and turn it. And assemble the main
both with the camera mount adaptor with the
screws. (Torx screw M4X18). Please make sure the
screws are tightly assembled for waterproof.
④ Screw the dome cover to the main body
and remove the protection vinyl from
the dome cover.
Notice
l Before starting the installation, make sure that the Camera ID and Protocol are set up properly.
Spring Wire Hook
END START

Page 11 / 16
Wiring/Cabling & Connecting
Port Description
l Main Cable
Port Pin Number (RJ45)
Connector / Wire Color
Signal
1 BLACK DC 12V
2 BROWN GND
3 ORANGE ALARM OUT/COM
4 WHITE OUT 2
5 YELLOW OUT1
6 GREEN SENSOR IN/COM
7 BLUE IN 1
8 GRAY IN 2
l Audio Cable
Port Pin Number Connector/ Wire Color
Signal
1 RCA (Yellow) Audio IN
2 Audio GND
3 RCA (White) Audio OUT
Connecting Power
1. Carefully check the voltage and current capacity of the rated power. The rated power is
indicated in the back of main unit.
2. After confirming the power source, connect power adaptor and connect the 12V DC
connector to the system
l For the DC input models, be careful with the polarity of DC power. The system should be

Page 12 / 16
permanently damaged by wrong DC input.
l In case that the length of the power wire is very long, there may be voltage drop and the
system may not work properly. Make the length of the power wire as short as possible.
Connecting Network
1. Plug network cable to Ethernet port (RJ-45 network port).
Connecting Video
1. To display video through the composite connect each port to a monitor using BNC coaxial
cable
Connecting Audio
Audio is full-duplex. It is possible to set the mode as Tx-only, Rx-only or Tx-Rx.
1. Connect audio input and output ports to audio devices accordingly.
2. The Audio signal required is line level, so an audio equipment with an amp, mixer or other
amplifier should be used.
Connecting Sensor and Alarm
Connect sensor and alarm devices to corresponding terminals accordingly.
l Sensor Input
l Relay Output
IN COM
IN 1
IN 2
Sensor 1
Sensor 2
V+
OUT
1
AC or DC
LOAD
Internal
OUT
2
LOAD
OUT COM

Page 13 / 16
Maximum allowable electrical load of relay is shown bellow table.
Drive Power DC Power AC Power
Max. Load Max DC 24V, 1A Max AC 125V, 0.5A
7. Dimension (mm)
200
207.8
150
220.3
50207.8
158.2
56.4 56.4
65 32.3
74.181.5
1.5" NPT
110
40
300
309.1
118.6
80
100
138.6
4- 8

Page 14 / 16
8. Specification
8.1. VPD200SM2Ti
Model Specification
Image sensor 1/2.8" 3.27M SONY Progressive scan CMOS image sensor for excellent image quality
Day & Night Auto/Color/BW
Environment OUTDOOR(IP66)
Optical Zoom 20X
Digital Zoom 12X
Lens 20x AF zoom ( f4.7~94mm (F1.6~F3.5)]
Min. illumination /
Light sensitivity (Lux)
[color] ICR off: 1.7Lux
ICR on: 0.3Lux
[B/W] ICR: 0.5Lux
ICR: 0.095Lux
Pan Tilt
Operation
Pan 360 Endless (400 deg/sec)
Tilt 0~90 deg (400 deg/sec)
WDR/BLC On/Off
Noise Reduction 2DNR
AE Mode Auto, Manual, Bright, Shutter Priority, Iris Priority,
GAIN Control Auto/Manual (-3 ~ 28dB)
Shutter Control Auto/Manual (1/1 ~ 1/10.000 sec)
White Balance Auto/Manual (Red, Blue Gain, Adjustable)
Video Compression H.264 High Profile@Level 4.0, Motion JPEG
Resolutions Up to 1920 x 1080
Frame rate H.264 Up to 30fps with 1920x1080
MJPEG Up to 30fps with VGA resolution
Video streaming Support multi stream with H.264, MJPEG
Adjustable frame rate
VBR/CBR in H.264
Image setting Day & Night
Auto White Balance
Auto Exposure
Effect - Color, Sharpness, Mirror/V-Flip, etc.
Privacy Mask
Output BNC x1, 1.0Vp-p, 75 ohm Composite Video, NTSC/PAL
Audio
Audio streaming Two-way, full duplex
Compression G.711
Sample Rate 8KHZ
Data Rate 64Kbps
Audio input Microphone input /1 x Line-In (Mono)
Audio output Line output/ 1 x Line-Out (Mono)
Network Security Password protection
User access log
HTTPS encryption
Supported
protocol HTTP, HTTPS, FTP, SMTP, UPnP, DNS, DynDNS, NTP, RTSP, RTP, TCP, UDP,
ICMP, DHCP
System
integration
Intelligent video Motion detection up to 1920x1080 with 4x3 blocks
Alarm trigger Motion detection
External input/Normal Open/Close Type
Alarm events File upload via ftp, e-mail
Notification via email, FTP and TCP
Video buffer 16MB pre-alarm and post-alarm
Recording Save to Micro SD card with event mode and continuous mode
Firmware upgrade
Remote upgrade via network

Page 15 / 16
API CGI Interface document
ActiveX Interface(ocx(dll) + document)
Physical RESET Button 1 x Factory Reset Button
Power Source DC 12V/5.0A
PoE High PoE (PoE+) 802.3at (Optional)
Power
Consumption Max. 36W
Weight (Appr.) Ceiling: 3,600g / Wall: 3,400g
LED's Power, Network Connection
Dimension(mm) Ceiling: 200(Ø) x 407.8 / Wall: 300(Ø)x309
Environ-
ment
Operating
Temperature -25 degree~50 degree Celsius (-13F~122F)
Storage
Temperature -25 degree~60 degree Celsius (-13F~140F)
Software Included Software
NVR Lite (16 Channel), IP Installer (Windows Only)
Package Contents Network Camera, Main Cable, Audio Cable, Lan Cable, Software CD
8.2. VPD200PM2Ti
Model Specification
Image sensor 1/3" 2.1M Progressive scan CMOS image sensor for excellent image quality
Day & Night Auto/Color/BW
Environment OUTDOOR(IP66)
Optical Zoom 20X
Digital Zoom 32X
Lens 20x AF zoom ( f4.7~94mm (F1.6~F3.5)]
Min. illumination /
Light sensitivity (Lux)
color] 0.5 Lux
DSS : 0.002 Lux
[B/W] 0.1 Lux
DSS : 0.001 Lux
Pan Tilt
Operation
Pan 360 Endless (400 deg/sec)
Tilt 0~90 deg (400 deg/sec)
WDR/BLC OFF/WDR/BLC
Noise Reduction (2D+3DNR) Auto/Off/Low/Middle/High
AE Mode Auto, Manual, Shutter Priority, Iris Priority,
GAIN Control Auto/Manual
Shutter Control 1/30 (25) ~ 1/60,000 sec
White Balance Auto/One push/Manual/Indoor/Outdoor
Video Compression H.264 High profile, Motion JPEG
Resolutions Up to 1920 x 1080
Frame rate H.264 Up to 30fps with 1920x1080
MJPEG Up to 30fps with VGA resolution
Video streaming Support multi stream with H.264, MJPEG
Adjustable frame rate
VBR/CBR in H.264
Image setting Day & Night
Auto White Balance
Auto Exposure
Effect - Color, Sharpness, Mirror/V-Flip, etc.
Privacy Mask
Output BNC x1, 1.0Vp-p, 75 ohm Composite Video, NTSC/PAL
Audio
Audio streaming Two-way, full duplex
Compression G.711
Sample Rate 8KHZ

Page 16 / 16
Data Rate 64Kbps
Audio input Microphone input /1 x Line-In (Mono)
Audio output Line output/ 1 x Line-Out (Mono)
Network Security Password protection
User access log
HTTPS encryption
Supported
protocol HTTP, HTTPS, FTP, SMTP, UPnP, DNS, DynDNS, NTP, RTSP, RTP, TCP, UDP,
ICMP, DHCP
System
integration
Intelligent video Motion detection up to 1920x1080 with 4x3 blocks
Alarm trigger Motion detection
External input/Normal Open/Close Type
Alarm events File upload via ftp, e-mail
Notification via email, FTP and TCP
Video buffer 16MB pre-alarm and post-alarm
Recording Save to Micro SD card with event mode and continuous mode
Firmware upgrade
Remote upgrade via network
API CGI Interface document
ActiveX Interface(ocx(dll) + document)
Physical RESET Button 1 x Factory Reset Button
Power Source DC 12V/5.0A
PoE High PoE (PoE+) 802.3at (Optional)
Power
Consumption Max. 36W
Weight (Appr.) Ceiling: 3,600g / Wall: 3,400g
LED's Power, Network Connection
Dimension(mm) Ceiling: 200(Ø) x 407.8 / Wall: 300(Ø)x309
Environ-
ment
Operating
Temperature -25 degree~50 degree Celsius (-13F~122F)
Storage
Temperature -25 degree~60 degree Celsius (-13F~140F)
Software Included Software
NVR Lite (16 Channel), IP Installer (Windows Only)
Package Contents Network Camera, Main Cable, Audio Cable, Lan Cable, Software CD