Vision VIS ZP3102 User manual

VIS_ZP3102
Z-Wave Motion Detector
Firmware Version : 4.84
Quick Start
AThis device is a wireless Z-Wave actor. A single click on the programming switch on the back side of
the enclosure (behind little hole) will confirm Inclusion and Exclusion. Opening the enclosure will wake up
the device and keep it awake.
Please refer to the chapters below for detailed information about all aspects of the products usage.
Product description
This motion detector (PIR = passive infrared receiver) detects the presence of a person in a room. The units
send information to a controller or any other associated Z-Wave device. The device is protected by a tamper
switch that will issue an alarm when the enclosure if opened. Beside the Motion detection the device also
reports the ambient temperature.
Installation Guidelines
1. Release the cover tap to open the cover.
2. Ensure that the system is properly powered. Insert the CR123A battery into the batter compartment and
the LED will start flashing slowly. This means that the device is not yet included into a Z-Wave network.
(c) 2016 Z-Wave Europe GmbH, Antonstr. 3, 09337 Hohenstein-Ernstthal, Germany, All rights reserved, www.zwaveeurope.com - pp 1

3. Using the adhesive tape to mount the device about 2 m above surface. To enhance operation place the
device on a position which can detect the room widely. See figure below. The solid areas are the areas
monitored.
Behavior within the Z-Wave network
IOn factory default the device does not belong to any Z-Wave network. The device needs to join an
existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also leave a network. This process is called Exclusion. Both processes are initiated by the
primary controller of the Z-Wave network. This controller will be turned into exclusion respective inclusion
mode. Please refer to your primary controllers manual on how to turn your controller into inclusion or
exclusion mode. Only if the primary controller is in inclusion or exclusion mode, this device can join or leave
the network. Leaving the network - i.e. being excluded - sets the device back to factory default.
If the device already belongs to a network, follow the exclusion process before including it in your network.
Otherwise inclusion of this device will fail. If the controller being included was a primary controller, it has to
be reset first.
A single click on the programming switch on the back side of the device will confirm Inclusion and
Exclusion.
(c) 2016 Z-Wave Europe GmbH, Antonstr. 3, 09337 Hohenstein-Ernstthal, Germany, All rights reserved, www.zwaveeurope.com - pp 2

Operating the device
The Motion detector will send a wireless signal every time a motion is detected. Please be aware that the
device will need some time to adjust after turning on. After power on and inclusion please waitfor 5 minute
before expecting correct operation.
Wakeup Intervals - how to communicate with the device?
WThis device is battery operated and turned into deep sleep state most of the time to save battery
life time. Communication with the device is limited. In order to communicate with the device, a static
controller Cis needed in the network. This controller will maintain a mailbox for the battery operated devices
and store commands that can not be received during deep sleep state. Without such a controller,
communication may become impossible and/or the battery life time is significantly decreased.
This device will wakeup regularly and announce the wakeup state by sending out a so called Wakeup
Notification. The controller can then empty the mailbox. Therefore, the device needs to be configured with
the desired wakeup interval and the node ID of the controller. If the device was included by a static
controller this controller will usually perform all necessary configurations. The wakeup interval is a tradeoff
between maximal battery life time and the desired responses of the device.
Opening the enclosure will wake up the device.
It is possible to set the node ID to 255 to send wakeup notifications as broadcast. In this mode device takes more time to
go to sleep and drains battery faster, but can notify all it's direct neighbors about a wakeup.
Node Information Frame
NI The Node Information Frame is the business card of a Z-Wave device. It contains information
about the device type and the technical capabilities. The inclusion and exclusion of the device is confirmed
by sending out a Node Information Frame. Beside this it may be needed for certain network operations to
send out a Node Information Frame.
A single click on the programming switch on the back side of the device will send out a Node Information
Frame.
Associations
AZ-Wave devices control other Z-Wave devices. The relationship between one device controlling
another device is called association. In order to control a different device, the controlling device needs to
maintain a list of devices that will receive controlling commands. These lists are called association groups
and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event
happens all devices stored in the respective association group will receive a common wireless command.
(c) 2016 Z-Wave Europe GmbH, Antonstr. 3, 09337 Hohenstein-Ernstthal, Germany, All rights reserved, www.zwaveeurope.com - pp 3

Association Groups:
1 Control Device when Motion is detected (max. nodes in group: 5)
Configuration Parameters
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can
adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow to configure signed values. In order to set values in the range 128
… 255 the value sent in the application shall be the desired value minus 256. For example: to set a
parameter to 200? it may be needed to set a value of 200 minus 256 = minus 56. In case of two byte value
the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Re-Trigger Waiting Time (Parameter Number 1, Parameter Size 1) Time until an associated device will turn
off if no new movement is detected
Value Description
129 — 127 Seconds
Technical Data
Battery Type 1 * CR123A
Explorer Frame Support Yes
SDK 4.54.00
Device Type Slave with routing capabilities
Generic Device Class Binary Sensor
Specific Device Class Routing Binary Sensor
Routing No
FLiRS No
Firmware Version 4.84
(c) 2016 Z-Wave Europe GmbH, Antonstr. 3, 09337 Hohenstein-Ernstthal, Germany, All rights reserved, www.zwaveeurope.com - pp 4