Vivo DESK-V201G User manual

26” x 19” Height Adjustable Desktop Workstation
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-v201g
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: DESK-V201G

2
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual and do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
WARNING!
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF DESK OR CHAIR
• USE TIPOVER RESTRAINT OR ANCHOR DESK TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
PACKAGE CONTENTS
B1 (x1)
Chair Leg
B2 (x2)
Chair Feet
B4 (x1)
Side Support Bar
B5 (x1)
Center Support
Bar
B6 (x1)
Seat Bottom
B3 (x1)
Support Bar
B8 (x1)
Desktop
B9 (x1)
Right Side
Drawer Slider
B10 (x1)
Le Side
Drawer Slider
B11 (x1)
Plastic Drawer
B12(x1)
Desk Leg
B13(x2)
Desk Feet
B7 (x1)
Seat Back
A1 (x8)
Metal Washer
A3(x12)
Plastic Washer
A4 (x4)
Long Thread Screw
A5(x2)
Knob
A2(x12)
Medium Screw
A6 (x4)
Short Screw
A8 (x4)
Long Screw
A9 (x1)
Hook
A10(x1)
Allen Wrench
A7 (x4)
Short Thread
Screw
NOTE: Not all hardware included will be used.

3
TOOLS NEEDED
ASSEMBLY STEPS
STEP 1
Attach chair legs (B1) to chair feet (B2), making sure legs are fully seated in openings. Secure feet using
4 medium screws (A2) and 4 metal lock washers (A1). Tighten with allen wrench (A10).
Phillips
Screwdriver
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
50lbs
(22.68kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury. 150lbs
(68.04kg)
DESK CHAIR
Assemble right side support bar (B3) to leg using 2 medium screws (A2) and 2 plastic washers (A3). The
support bar has a large hole on the le side which will face inward. Tighten with allen wrench. Slide
center support bar (B5) into large hole on right side bar. Slide le side support bar (B4) onto center bar,
and secure to legs with 2 medium screws (A2) and 2 plastic washers (A3). Tighten with allen wrench.

4
STEP 2
Secure seat back using knobs (A5). Adjust chair feet to sit level if needed.
STEP 3
Mount plastic seat bottom (B6) to assembled chair frame using 4 long plastic thread screws (A4).
Tighten with phillips screwdriver. Slide plastic seat back (B7) onto chair frame, aligning upper or lower
holes in seat back with screw holes in frame depending on the needed height.

5
STEP 4
Assemble right side drawer slider (B9) to desktop
(B8) using 2 short screws (A6) and 2 plastic washers
(A3). Tighten with allen wrench. Check to ensure
slider pulls out towards the front of the desk.
STEP 5
Assemble le side drawer slider (B10) to
desktop using 2 short screws (A6) and 2
plastic washers (A3). Tighten with allen
wrench.
Mount plastic drawer (B11) to sliders
using 4 short plastic thread screws (A7).
Tighten with screwdriver.
Attach desk legs (B12) to desk feet (B13), making sure legs are fully seated in openings. Secure feet
using 4 medium screws (A2) and 4 metal lock washers (A1). Tighten with allen wrench.

6
STEP 5 (cont.)
STEP 6
Assemble desktop to legs using 4 long screws (A8) and 4 plastic washers (A3). Tighten with allen
wrench.
Squeeze sides of hook (A9) and fit into slot on le or right side of desk. Adjust desk feet to sit level if
needed.
Loosen knobs on sides of desk to adjust desk
tilt angle, and tighten knobs to secure position.
STEP 7

7
Height Adjustment
RAISE:
Step on the support bar with one foot and pull up with even motion on both sides of the desk, until it
reaches desired height. Repeat with chair.
LOWER:
Step on the support bar with one foot and pull up with even motion on both sides of the desk, until it
reaches max height. Slowly lower down to desired height. Repeat with chair.
Raise desktop slowly
to keep items stable.
Keep monitor and laptop
base fully on the desktop.
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.

If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654
Last Updated: 05/13/2019