Vivo STAND-SIT2E User manual

Electric Sit-Stand Workstation
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-sit2e
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: STAND-SIT2E

2 3
WARNING!
TOOLS NEEDED
44lbs
(19.96kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC
SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR
SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
A (x1)
Pole
B(x1)
Base
C(x1)
Decorative
Cover
J (x1)
4mm Allen
Wrench
D(x1)
Arm
E(x1)
Tray
F (x1)
Power Cord
G(x2)
M8x24
H (x4)
M6x10
I (x4)
M6x20
M-A (x8)
M4x12
M-C (x8)
M4x16
M-B (x8)
M5x12
M-D (x8)
M5x16
M-F (x8)
Spacer
M-E (x8)
D5 Washer
K (x1)
6mm Allen
Wrench
A( x1)
ASSEMBLY STEPS
STEP 1
Attach pole (A) to base (B) with M6x20 screws (I) using
4mm allen wrench (J).
A
B
I

4 5
STEP 3
Insert two more screws (H) into the bottom 2 holes at the base of pole (A) using 4mm allen wrench.
Tighten all 4 screws.
J
H
Insert power cord (F) at base of pole (A). Slide decorative cover (C) onto base of pole (A).
STEP 4
N
O P
C
Use up arrow to raise tray (E). Insert screws (G) into bottom of tray (E) as shown in diagram.
STEP 5
N
G
O
Insert two screws (H) into the top 2 holes at the base of pole (A) using 4mm allen wrench (J) as shown
in diagram. Do not tighten completely. Hang tray (E) on screws just inserted.
STEP 2
J
H
N
O
6mm
E
STEP 6
Remove VESA plates by turning knob counterclockwise. Keep all parts nearby.
D

6 7
Attach VESA plates to the mounts of arm (D) using knobs.
STEP 9
STEP 11
Adjust tilt of monitors as desired. Store allen wrenches in decorative cover (C).
J
K
�
STEP 10
Tighten with 5mm allen wrench (K).
K
STEP 7
Slide arm (D) onto pole (A) and tighten at desired height using 4mm allen wrench (J).
1
OPTION A: Flat Back Monitor
For at back monitors, attach VESA plates using
12mm screws (M-A or M-B) with washers (M-E).
STEP 8
OPTION B: Curved Back Monitor
For curved or recessed back monitors, use 16mm
screws (M-C or M-D) with washers (M-E) and
spacers (M-F).
MA MB-/ -
ME-
ME-
MF-
MC MD-/ -
OPERATING INSTRUCTIONS
Upward and Downward Movement
Press and hold the up or down arrow until the workstation reaches the desired height. If motor
continuously operates for a relatively long period of time, the overheat protection will activate. The
control panel will work normally again aer approximately 20 min.
Overload Protection Mode
While operating, should the load on the desk exceed rated specications, the system will enter into
overload protection mode to protect the system from damage. When this happens, the workstation will
move downward approximately 30mm and come to a stop with the current height displayed.
Reset Mode
While the unit is powered on, press the down arrow until workstation moves to the fully lowered position.
Don’t release until it raises approximately 5mm and automatically stops.
+/-45°
+/-30°
180°

Last Updated: 11/15/2018
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654