Vivo CART-PC02HB User manual

Black 24” Mobile Computer Workstation
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/cart-pc02hb
SKU: CART-PC02HB
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
A(x1)
Desktop
B(x1)
Base
C (x1)
Pole with
Handle
D (x1)
Keyboard
Tray
E(x1)
Printer Shelf
PACKAGE CONTENTS
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF CART.
• USE TIPOVER RESTRAINT OR ANCHOR CART TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
TOOLS NEEDED
Phillips
Screwdriver
F(x2)
Caster
G(x2)
Locking
Caster
H (x1)
Lower Shelf
Bracket
I (x1)
CPU Holder
Mount
J(x1)
CPU Holder
K(x2)
Keyboard
Tray Bracket
L(x4)
Adhesive Pad
M (x2)
Cable Clip
S-A (x3)
M6x12mm Screw
S-B (x4)
M6x16mm Screw
S-C (x14)
M6x12mm Screw
S-D (x4)
M6x8mm Screw
T-A (x1)
4mm Allen Wrench
T-B (x1)
5mm Allen Wrench
T-C (x1)
Wrench
22 lbs
(10 kg)
Per Tray
17.5 lbs
(8 kg)
Worksurface
4.4 lbs
(2 kg)
Keyboard
Tray
22 lbs
(10 kg)
CPU Mount

3
ASSEMBLY STEPS
STEP 1
Screw Casters (F, G) into Base (B).
Adjust Casters (F, G) to sit level on the
oor if needed, then tighten the nut
on each stem against Base (B) using
Wrench (T-C).
STEP 2
Assemble the Pole With Handle (C) to
Desktop (A) using M6x16mm Screws
(S-B) for the pole and M6x12mm Screws
(S-C) for the handle. Tighten the screws
with Allen Wrenches (T-A, T-B).
STEP 3
Assemble Keyboard Tray Brackets
(K) to Keyboard Tray (D) using
M6x12mm Screws (S-C) and
tighten with 4mm Allen Wrench
(T-A).
F
F
G
G
B
K
D
S-C T-A
A
S-B S-C
T-B
T-A
C
T-C

4
STEP 4
Attach assembled keyboard tray to Desktop (A)
using M6x12mm Screws (S-C) and tighten with
4mm Allen Wrench (T-A).
Loosen the screw on Lower Shelf Bracket (H) using a Phillips screwdriver.
Slide the bracket onto the bottom of Pole with Handle (C), then place the
pole into Base (B).
STEP 5
Secure Base (B) to Pole with Handle (C) using M6x12mm Screws (S-A) and tighten with
5mm Allen Wrench (T-B).
STEP 6
T-B
S-A
B
C
C
B
H
A
T-A
S-C

5
STEP 7
Peel backing from Adhesive Pads (L) and apply pads to CPU Holder Mount (I) and CPU
Holder (J). Remove knobs from CPU Holder (J).
Attach assembled CPU holder to le or right side of Lower Shelf Bracket (H) using
M6x8mm Screws (S-D) with a Phillips screwdriver. If needed, adjust the handle by
turning the knob on the back of the handle as shown. The handle should have a
rm feeling with little or no slop.
STEP 9
STEP 8
Assemble CPU Holder (J) and CPU Holder
Mount (I) using previously removed
knobs.
1 2
3 4
H
S-D
J
I
J
L
I

6
STEP 10
Attach Printer Shelf (E) to Lower Shelf Bracket (H) opposite from the CPU holder
using M6x8mm Screws (S-D) with a Phillips screwdriver. Slide the CPU holder
and shelf assembly down so the bumpers are resting on the base, and tighten the
screw on Lower Shelf Bracket (H) using a Phillips screwdriver.
STEP 11
Thread the straps of the CPU Holder (J) through slots on CPU Holder Mount (I) and turn
ends of straps to form a “T”, locking the straps into the slots.
J
I
E
S-D
H
Bumpers

7
Place monitor, keyboard and other items onto desk. Apply Cable Clips (M) where desired to
manage wires from keyboard and mouse. Loosen knobs on CPU holder, adjust holder width
to t CPU tower, then tighten. Unlock buckles on straps and extend straps. Place CPU
tower in holder, pull straps tight around CPU tower, then lock the buckles.
NOTE: To prevent movement, press levers on the locking casters down. Pull levers up to
allow movement.
STEP 12
2
1
buckle
3
M

LAST UPDATED: 12/13/2021
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303