Vivo DESK-SF02W User manual

White Wall Mounted Drop-Down Cabinet
and Desk
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-sf02w
SKU: DESK-SF02W
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2 3
STEP 2
Insert x8 Wood Dowel Pins (P) into edges of Rear Panel (B).
PACKAGE CONTENTS
TOOLS NEEDED
33lbs
15kg
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
A (x1)
Top Panel
B(x1)
Rear Panel C(x1)
Le Panel
D (x1)
Bottom Panel
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
Drill
Level
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS.
ADULT SUPERVISION IS REQUIRED.
ASSEMBLY STEPS
STEP 1
Insert x3 Cam Lock Screws (O) into Bottom Panel (D), and x2 Wood Dowel Pins (P) into
sides of Panel.
E (x1)
Front Panel
F(x1)
Right Panel
G(x2)
Hinge
H (x1)
Handle
I (x2)
Small Plug
J(x1)
Magnet
K (x2)
Upper Ball Joint
L (x2)
Lower Ball
Joint
M(x2)
Strut
N(x1)
Bumper
O (x18)
Cam Lock Screw
W-A (x8)
Wall Screw
W-B (x8)
Self Tapping
DrywallAnchor
W-C (x8)
Washer
P (x12)
Wood Dowel
Pin
Q(x18)
Cam Lock Nut
R(x8)
Large Plug
S (x14)
ST4x16
T (x12)
ST2.9x12
U (x2)
M4x8
V(x4)
ST5.5x50
STEP 3
Assemble Rear Panel (B) to Bottom Panel (D).

4
STEP 8
STEP 9
Extend the Struts (M) to their full length. Snap small ends onto Lower Ball Joints (L).
Attach Upper Ball Joints (K) to Le and Right Panels (C, F) using x6 ST4x16 Screws (S). Snap
large ends of Struts onto Upper Ball Joints, then attach Lower Ball Joints to Front Panel (E)
using x6 ST4x16 Screws (S), making sure each ball is facing out.
With the assembled cabinet standing up, place the Front Panel (E) face-down in front with the
bottom edge flush with the cabinet. Assemble the Hinges (G) to the cutouts in the assembled
cabinet and Front Panel using ST2.9x12 Screws (T), making sure the Phillips head on each
Hinge is facing into the cabinet as shown in the diagram.
Close the assembled cabinet and check alignment of the Front Panel. If the Panel is not
aligned, turn the Phillips head screw on each Hinge to align the Panel.
STEP 5
Assemble Le and Right Panels (C, F) to previously assembled Bottom and Rear Panel (B, D), then
place Top Panel (A) onto assembled cabinet.
STEP 4
Insert x4 Cam Lock Screws (O) into Le Panel (C) and x1 Wood Dowel Pin into top of Panel (C).
Repeat for Right Panel (F). Insert x7 Cam Lock Screws into Top Panel (A).
STEP 6
Insert all cam lock nuts(Q) into Bottom, Rear, Le and Right Panels. Turn all plugs clockwise
using a Phillips screwdriver to lock Panels together.
STEP 7
Attach Handle (H) to front of Front Panel (E) using M4x8 Bolts (U). Once tightened, insert
Small Plugs (I) into holes.
5
Keep the magnet (J) aligned
with the edge of the top
panel (A) while tightening.

Determine desired location of desk on wall. Use a stud finder to determine if any vertical set
of holes can be mounted into a wood stud or not. With the help of a partner, hold desk against
wall and mark (8X) mounting locations through Rear Panel (B). Use of a level is recommended.
Then proceed to Options A or B below.
Note: This desk is designed to mount securely in drywall only. However, it is still recommended
to install at least one set of vertical mounting points in a wood stud. Two sets of mounting
points are spaced 16” apart for the most secure mounting option (Option A below).
Option A: Wood Stud Installation
For all locations that line up with a stud, drill 1.75” (45mm) deep holes using a 1/8” (3mm)
bit. If attaching desk with the 4X locations for wood studs, mount desk to wall using (4X)
ST5.5x50mm screws (W) with (4X) washers (W-C). Install large plugs (R) over all holes on rear
panel (B).
STEP 10
Press Bumper (N) into holes in Bottom Panel (D).
STEP 11
STEP 12
Place laptop and other items on desk when open and in use. When not in use, all devices may be
stored inside.
67
Option B: Drywall Installation
For all locations that do not line up with a stud, insert self-tapping drywall anchors (W-B)
using phillips screwdriver. If attaching desk with the 8X locations in drywall, mount desk
to wall using (8X) ST4x35mm screws (W-A) with (8X) washers (W-C). Install mounting hole
covers (R) over all holes on rear panel (B).
Note: If attaching desk with 2X locations in wood stud, refer to Option A for wood stud
drilling and installation instructions. The remaining 4X mounting points should still be
installed in drywall.
STEP 11 (Continued)
R
R

LAST UPDATED: 10/28/2020
REV2
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303