Vivo DESK-V000VN User manual

Corner Desk Riser
Instruction Manual
SKU: DESK-V000VC/N/W
Assembly Video & Product Info
https://vivo-us.com/products/desk-v000vc

2 3
A (x1)
Desk Riser
B(x2)
Extended Feet
S-A (x10)
M5x10mm Screw
F (x2)
Zipties
D (x1)
Keyboard
Tray
E (x1)
Cable Clips
Phillips
Screwdriver
Scissors
C (x1)
Keyboard
Brackets
If you do not understand these directions, or if you have any doubts about the safety of the installation, please
contact our product support team at 309-278-5303 or [email protected]om for further assistance. Check carefully to
make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not
use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We
cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
LBS
CAUTION!
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
DO NOT EXCEED WEIGHT CAPACITY
FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY.
Package Contents
We’re Here for You
Included Hardware & Tools
Tools Needed:
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
Chat Us:
www.vivo-us.com
Give us a Call:
309-278-5303
Email Us:
[email protected]om AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
Weight Capacity:
33lbs
(15kg)
WARNING: PINCH POINT
DO NOT PLACE HANDS ON OR NEAR SUPPORT BARS. MOVING PARTS CAN CRUSH AND CUT.
PINCH POINTS ARE CREATED DURING LIFTING AND
LOWERING THE WORKSURFACE. FAILURE TO FOLLOW THESE
INSTRUCTIONS MAY RESULT IN SERIOUS PERSONAL INJURY.

4 5
ASSEMBLY STEPS
STEP 1
STEP 3
STEP 4
Carefully remove Desktop (A) from the packaging.
Flip Desktop (A) upside down, then attach the Extended Feet (B) to frame using
M5x10mm Screws (S-A).
Press the handles on each side and li Desktop (A).
Mount Brackets (C) to Keyboard Tray (D) using M5x10mm Screws (S-A).
A
STEP 2
WARNING:
IMPACT HAZARD! MOVING
PARTS CAN CRUST & CUT.
S-A (x4) S-A (x6)
S-A
B
C
D
S-A

6 7
STEP 5 ASSEMBLY COMPLETE
STEP 6
Hang assembled keyboard tray onto pre-installed knobs, and tighten knobs to secure.
NOTE: Make sure the keyboard brackets are curving towards the user, not towards the
inside of the desk.
Attach Cable Clip (D) to desk to manage keyboard and mouse cables. Manage cables
using Zipties (E).
D
E
Assembly is complete and your desk riser is now ready for use.
Press both side levers to raise or lower your desk riser.
When lowering without any weight on the desktop, lightly press down on riser as you lower
it to allow for a smoother lowering process. If it feels diicult to lower aer placing laptop
and other intended setup items, apply light pressure to lower smoothly or add additional
weight.
Please note the 33lb weight capacity when adding weight.

8 9
TENSION ADJUSTMENT
If your desk riser lis up or down too easily, or is
too diicult, the gas spring cable can be adjusted
to your desired tension.
This adjustment is located in two places:
1. Levers: Behind both levers, under desktop.
2. Gas Spring Tip: At the tip of the Gas Spring
Notes:
- The images will focus on the adjusting near
the Levers, but the process are the same, and
the steps can be applied to either location.
1
2
1
Begin by loosening the Inner (1) and Outer (2) Nuts using an adjustable wrench. Loosen
Nuts until they are both on the opposite ends of the Gas Spring Cable.
Gas Spring
Cable
2
1
2
- Any adjustments made need to
be applied to both side of the riser.
- Images shown here show the
maximum and minimum tensions.
In most cases, your ideal tension
will be somwhere in the middle.
If the desk feels diicult to raise and lower, then you will need to increase the Gas Spring
Cable tension. Gently pull the cable away from the Lever until the Inner Nut (2) is firmly
pressed against the middle divider.
Option A:
Desk Is Diicult to Raise/Lower | Increase Tension
Tighten Outer Nut (1) until it firmly holds the cable in its position, as shown below.
2
1
TENSION - CONT’D

10 11
TENSION - CONT’D
1
If the desk is raising or lowering without the handle being pressed, then the tension needs
to be loosened. Gently push the cable towards the Lever the Outer Nut (1) is firmly pressed
against the middle divider.
Option B:
Desk Raises/Lowers Too Easily | Decrease Tension
Tighten Inner Nut (2) until it firmly holds the cable in its position, as shown below.
2

LAST UPDATED: 10/16/2023
REV1.1
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
Monday-Friday from 7:00am-7:00pm CST
Need Help? Get In Touch
FOR MORE GREAT VIVO PRODUCTS,
CHECK OUT OUR WEBSITE AT: WWW.VIVO-US.COM
VIVO-us @vivo_us