Vivo DESK-SKIRT-30 User manual

Black 30” Cable
Management Desk
Organizer
Instruction Manual
SKU: DESK-SKIRT-30
Assembly Video & Product Info
www.vivo-us.com/products/desk-skirt-30

2
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please contact our product support team at 309-278-5303 or [e-mail] for further assistance.
Check carefully to make sure there are no missing or defective parts. Improper installation may cause
damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
CAUTION!
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
We’re Here for You
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
Chat Us:
www.vivo-us.com
Give us a Call:
309-278-5303
Email Us:
[email protected]om AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
AVG. RESOLUTION TIME (within oice hrs): 5M 4S

3
Package Contents
Included Hardware
Tools Needed:
B(x2)
Side Bar
C(x2)
Mounting Clip
A (x1)
Panel
D (x4)
Upper/Lower
Bar
DrillPhillips
Screwdriver
E (x6)
Joining Tube
S-A (x2)
ST4.8x19 Screw
Pencil

4
ASSEMBLY STEPS
STEP 1
Assemble the steel bar frame using the Side Bars (B), Upper/Lower Bars (D) and Joining Tubes (E).
Lighty tap each joint against a hard surface to ensure all bars and joiners are full pressed in.
STEP 2
NOTE: Ensure all bars and joiners are fully pressed in for a secure fit.
Open the flap and straps of the Panel (A) and insert the frame, making sure the frame is fully
inserted and the material is tightly stretched around it.
Snug Fit:
Fabric on panel has a tight fit around the frame and may need to be
stretched before inserting the frame.
B
ED
A

5
STEP 3
STEP 4
Fasten the straps on Panel (A) to around the assembled frame to secure.
Place the Mounting Clips (C) in the center of each exposed portion of the steel bars.
NOTE: Make sure the wire management flap on the
panel (A) is facing the inside of the desktop.
A
C
A

6
STEP 5
STEP 6
Center the assembled panel under the desktop.
Mark the locations of the Mounting Clips (C) using a pencil. Drill pilot holes using a 1/8” (3mm) bit
and mount the assembled panel to the underside of the desk using the ST4.8x19 Screws (S-A) as
shown.
NOTE: Desktop must be at least 1” thick to prevent screws from poking out through the top
and damaging the surface.
S-A

7
STEP 7
Route and organize the cables and secure them using the flap on the panel (A).
A

LAST UPDATED: 01/08/24
REV2
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
Monday-Friday from 7:00am-7:00pm CST
Need Help? Get In Touch
FOR MORE GREAT VIVO PRODUCTS,
CHECK OUT OUR WEBSITE AT: WWW.VIVO-US.COM
VIVO-us @vivo_us