Vivo CART-V04C User manual

Mobile Projector Cart
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/cart-v04c
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: CART-V04C

2 3
PACKAGE CONTENTS
WARNING!
A1 (x5)
M6x65
A2 (x9)
Washer
A3 (x8)
Nut
A4 (x4)
M6x12
A5 (x4)
M6x30
A6 (x3)
M6x50
A7 (x1)
Washer
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF CART.
• USE TIPOVER RESTRAINT OR ANCHOR CART TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
ASSEMBLY STEPS
STEP 1
Place the base (B2) upside down and attach the feet (B1) using four M6x65 bolts (A1), four washers
(A2), and four nuts (A3). Tighten using provided wrench (A9).
STEP 2
A8 (x1)
M6x50
A9 (x1)
Wrench
A10 (x1)
Allen Key
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
Attach casters (G1,G2) to feet (B1) using wrench (A9) as shown in diagram.
G1 (x2)
Caster
G2 (x2)
Locking Caster
G3 (x3)
Knob
G4 (x2)
Plate
B1x2
B2
B3
B4
B5
B1 (x2)
Feet
B2 (x1)
Base
B3 (x1)
Center Pole
B4 (x1)
Lower Shelf
B5 (x1)
Top Shelf
A1x4
A3x4 A2x4
B1
B1
A9x1
B2
G2x2
G1x2
A9x1
A9x1
22 lbs
(10 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Per Tray
TOOLS NEEDED
Phillips
Screwdriver

4 5
STEP 3
Turn assembly over and attach center pole (B3) using four M6x12 bolts (A4). Tighten using Allen key
(A10).
Secure center pole (B3) to base (B2) using one M6x65 bolt (A1), one washer (A2), and one nut (A3).
Tighten with wrench (A9).
STEP 4
STEP 5
Attach lower shelf (B4) using two M6x30 bolts (A5), two washers (A2), and two nuts (A3). Tighten with
wrench (A9) and Phillips screwdriver (not included).
Adjust the height of center pole (B3) and secure in place using two M6x50 bolts (A6) and two
adjustment knobs (G3).
STEP 6
A4x4
B3
A10x1
A1x1
A2x1
A3x1
A9x1
A2x2
A3x2
A5x2
B4
A9x1
G3x2
A6x2

6 7
STEP 7
Secure two plates (G4) to either side of center pole (B3). Place top shelf (B5) over assembly. Attach top shelf (B5) using one M6x50 bolt (A8), two washers (A2), and one nut (A3) in the top hole. Use
one M6x50 bolt (A6), washer (A7), and knob (G3) in bottom hole.
STEP 8
B5
G4x2
1
2
A3x1
A9x1
A2x2
A8x1
A10x1
A7x1
A6x1 G3x1

Last Updated: 11/12/2018
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654