Vivo DESK-SKIRT-60P User manual

Black Clamp-on 60” Cable Management Desk Organizer
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-skirt-60p
SKU: DESK-SKIRT-60P
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
Phillips
Screwdriver
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual and do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or
inappropriate use.
PACKAGE CONTENTS
TOOLS NEEDED
ASSEMBLY STEPS
STEP 1
WARNING!
B (x2)
Side Bar
M-A (x3)
3/4” Screw
E (x3)
Mounting Clip
F (x6)
Upper/Lower
Bar
H (x4)
Joiner
A (x1)
Panel
Connect the centers of the T Joiners (C) to the ends of the Middle Bars (G). Connect the Upper/Lower
Bars (F) to the sides of the T Joiners (C), then connect the Joiners (H) and Side Bars (B) to the sides to
complete the frame assembly.
Drill Pencil
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
C (x4)
T Joiner
G (x2)
Middle Bar
D (x2)
Clamp
S-A (x2)
Screw
C
G
FH
B

3
STEP 2
Open the flap and straps of Panel (A) and insert the frame, making sure the frame is fully inserted and
the material is tightly stretched around it.
A
STEP 3
Fasten the straps on Panel (A) to secure the frame.
A
STEP 4
Place Mounting Clips (E) in the center of each exposed portion of Upper/Lower Bars (F).
NOTE: Make sure the wire management flap on Panel (A) is facing upward.
E
F
A

4
STEP 5
For thinner desktops (<1.5” (40mm)), adjust Clamp (D) by disassembling, flipping the bottom
bracket, and reassembling using a Phillips screwdriver.
D
STEP 6
E
S-A
Secure Mounting Clips (E) to Clamp (D) in one of four mounting locations using Screws (S-A).

5
STEP 7
Mount the assembled panel to the desktop and tighten Clamps (D) to secure the assembly in place.
STEP 8
Route and organize the cables and secure them using the flap on the panel (A).
A

6
Screw Mounting
Center the assembled panel under the desktop.
STEP 5 (Optional)
STEP 4 (Optional)
E
Screw Mounting
Place the Mounting Clips (E) in the center of each
exposed portion of Upper/Lower Bars (F).
NOTE: Make sure the wire management flap on Panel (A) is facing the inside of the desktop.
A
F

7
STEP 7 (Optional)
Screw Mounting
Route and organize the cables and secure them using the flap on Panel (A).
A
STEP 6 (Optional)
Screw Mounting
Mark the locations of Mounting Clips (E) using a pencil. Drill pilot holes using a 1/8” (3mm) bit and
mount the assembled panel to the underside of the desk using 3/4” Screws (M-A) as shown.
NOTE: Desktop must be at least 1” thick to prevent screws from poking out through the top and damaging the surface.
E
M-A

LAST UPDATED: 11/07/2021
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303