Vivo STAND-RACE1A User manual

Racing Steering Wheel Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-race1a
SKU: STAND-RACE1A
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2 3
ASSEMBLY STEPS
STEP 1
Peel the backing o of the foot pads (D) and apply pads to the bottom of each foot (C). Screw the feet
into the base of the stand (A).
PACKAGE CONTENTS
TOOLS NEEDED
44lbs
(20kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
A (x1)
Stand
B(x1)
Upright Support
Bracket
C(x4)
Foot
J (x1)
Shier Support
K (x4)
Cheese Head
Bolt
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
D(x4)
Foot Pad
E(x2)
Cable Clip
F (x4)
Round Head
Bolt
G(x6)
Ziptie
H (x1)
Allen Wrench
I (x1)
Shier Support
Bracket
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
STEP 2
Loosen the knobs on the middle of the post, then extend the post. Remove the two knobs locking the
post in the folded position. Raise the post, then install the upright support bracket (B) to the base
and post using x2 round head bolts (F) and the previously removed knobs. Tighten the bolts with the
Allen wrench (H).
STEP 3
Tilt the wheel support plate up to the desired angle, then insert x2 round head bolts (F) to secure the
tilt angle. Tighten with the Allen wrench (H).

4 5
STEP 4 STEP 6
Adjust the post to the desired height, then tighten the knobs to secure the height.
Install the shier support bracket (I) to the le or right side of the wheel support plate using x2
cheese head bolts (K). Tighten with the Allen wrench (H).
STEP 7
STEP 5
Adjust the foot plate to the desired angle and reinsert the previously removed knobs.
Remove the knobs from the foot plate. Remove the bolts using the Allen wrench (H), move the plate
to the desired position, then reinstall the bolts.

6 7
STEP 8 STEP 10
STEP 9
Attach the cable clips (E) to the post for cable management.
Mount the shier support (J) to the support bracket using x2 cheese head bolts (K) and tighten with
the Allen wrench (H). The support may be installed to the close or far position depending on user
preference.
FOLDING INSTRUCTIONS
Remove the lower two knobs (A1) from the upright support bracket (B) and gently fold the post down.
Loosen the knobs on the middle of the post to extend for clearance if needed. Reinsert the previously
removed knobs into the sides to lock the post in the folded position.

LAST UPDATED: 04/02 /2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303