Vivo MOUNT-CUB2D User manual

Cubicle Monitor Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-cub2d
SKU: MOUNT-CUB2D
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MOUNT OR
MONITOR
• USE TIPOVER RESTRAINT
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
A (x1)
Main Plate
B(x1)
Clamp Plate
C(x1)
VESA Support
Plate
P(x1)
M8x20
J (x4)
M4x30
L (x1)
Oval Pate
D(x1)
VESA Plate
E(x4)
M6x22 Bolt
F (x4)
M6 Washer
G(x4)
M4/M6 Spacer
H (x1)
Allen Key
I (x4)
M4x12
Q(x1)
Plastic Knob
M (x1)
M4x12
K (x1)
Clamp Knob
O (x2)
M8x12
N (x1)
M4 Washer
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

3
ASSEMBLY STEPS - OPTION A: DESK MOUNT
STEP 1
TOOLS NEEDED
22lbs
(9.98kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
STEP 2
Screw the Clamp Knob (K) into the Clamp Plate
(B). For a desk thickness of 1/2” to 2”, the plastic
handle is on the same side as the mounting lip
on the plate, and for a desk thickness of 1-1/2” to
3”, the plastic handle is on the opposite side from
the lip (please note, maximum monitor height is
aected by desk thickness). Assemble the Oval
Plate (L) to the Clamp Knob using the M4x12 Bolt
(M) and M4 Washer (N).
Mount the assembled clamp to the Main Plate (A)
using the M8x12 Bolts (O), and tighten with the
5mm Allen Key (H).
ÅÇ
Ä
_
~
NM
K
B
L
E
^
É
A
E
STEP 3
Tighten the Main Plate with clamp to the desk. Do
not overtighten, as this may cause the stand to lean
back.

4
STEP 4
Mount the VESA Support Plate (C) to the Main Plate at the desired height using M6x22 Bolts (E) and
M6 Washers (F), and tighten with the 4mm Allen Key (H). If the monitor will be removed frequently or
the back of the stand must be flush, use M4/M6 Spacers (G) between the VESA Support Plate and Main
Plate. Please note, the lever must be facing down.
STEP 5
OPTION A: Flat Back Monitor
For monitors with a flat back, mount the VESA
Plate (D) using M4x12 Bolts (I).
OPTION B: Curved Back Monitor
For monitors with a curved or recessed back,
mount the VESA Plate (D) using M4x30 Bolts (J)
and M4/M6 Spacers (G).
STEP 6
Mount the VESA Support Plate (C) to the Main Plate at the desired height using M6x22 Bolts (E) and
M6 Washers (F), and tighten with the 4mm Allen Key (H). If the monitor will be removed frequently or
the back of the stand must be flush, use M4/M6 Spacers (G) between the VESA Support Plate and Main
Plate. Please note, the lever must be facing down.
bc
EF

5
Ö
Ñ
_
PB
Q
STEP 7
To remove the monitor, pull the release lever on the VESA Support Plate forward and li the monitor.
STEP 1
OPTION A
For a cubicle wall thickness of up to 1-3/8”, install the Clamp Plate (B) to the Main Plate (A) with the
long side facing in. Secure with the M8x20 Bolt (P) and Plastic Knob (Q), but do not tighten. Hang
the Main Plate with Clamp Plate over the cubicle wall. Move the plates together against the wall and
tighten the Plastic Knob.
ASSEMBLY STEPS - OPTION B: CUBICLE MOUNT
OPTION B
For a cubicle wall thickness of 1” to 2.4”, install the Clamp Plate (B) to the Main Plate (A) with the long
side facing out. Secure with the M8x20 Bolt (P) and Plastic Knob (Q), but do not tighten. Hang the Main
Plate with Clamp Plate over the cubicle wall. Move the plates together against the wall and tighten the
Plastic Knob.
switch
switch
Ö
Ñ
_
^
A
B
Q
P

6
STEP 2
Mount the VESA Support Plate (C) to the Main Plate at the desired height using M6x22 Bolts (E) and
M6 Washers (F), and tighten with the 4mm Allen Key (H). If the monitor will be removed frequently or
the back of the stand must be flush, use M4/M6 Spacers (G) between the VESA Support Plate and Main
Plate. Please note, the lever must be facing down.
STEP 3
OPTION A: Flat Back Monitor
For monitors with a flat back, mount the VESA
Plate (D) using M4x12 Bolts (I).
OPTION B: Curved Back Monitor
For monitors with a curved or recessed back,
mount the VESA Plate (D) using M4x30 Bolts (J)
and M4/M6 Spacers (G).

7
STEP 4
Slide monitor with VESA Plate onto the VESA Support Plate. There will be a “click” when the monitor
is fully seated and locked.
STEP 5
To remove the monitor, pull the release lever on the VESA Support Plate forward and li the monitor.
switch

LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303