Vivo STAND-V004P User manual

Quad Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v004p
SKU: STAND-V004P
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Base
B(x1)
Pole
C(x1)
Pole
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
D (x2)
Arm
E (x1)
Pole Adapter
F (x2)
Cable Clip
G (x1)
Cover
H (x1)
3mm Allen
Wrench
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M-C (x16)
D5 Washer
I (x1)
5mm Allen
Wrench
J(x1)
6mm Allen
Wrench
M-B (x16)
M5x12
M-A (x16)
M4x12
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARD
OR BACKWARD.
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

3
ASSEMBLY STEPS
TOOLS NEEDED
Phillips
Screwdriver
STEP 1
STEP 2
Slide one cable management clip (F) and cover (G) onto pole (B) from bottom. Thread pole (B) into
base (A). Tighten grub screws at base using 3mm allen wrench (H). Slide cover down.
Adjust stopper at desired height using 3mm allen wrench (H).
B
F
GH
A
H
17.6lbs
(8 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM

4
STEP 3
STEP 4
Slide arm (D) onto pole (B). Tighten with 5mm allen wrench (I).
Thread pole adapter (E) onto pole (B). Slide cable management clip (F) onto pole (C) from bottom.
Thread pole (C) into pole adapter (E). Tighten grub screws in pole adapter (E) with 3mm allen wrench
(H). Adjust stopper as desired using 3mm allen wrench (H).
I
D
F
E
C
H
H

5
STEP 5
STEP 6
Slide arm (D) onto pole (C). Tighten with 5mm allen wrench (I).
Insert screws (M-A or M-B) with washers (M-C) into top 2 holes of monitors. Leave slightly loosened.
Slide monitors onto VESA Plates from above. Insert screws (M-A or M-B) with washers (M-C) into
bottom 2 holes of monitors. Tighten all screws.
D
I
M- A
M- B
M- C
1 2
3m m
3
M- A
M- B
M- C

6
STEP 7
Adjust the tilt angle of the monitors. If the weight of the monitors is not supported, tighten joints with
6mm allen wrench (J) as shown in diagram.
STEP 8
Store allen wrenches (H, I, J) as shown in diagram.
+45 °
-45°
J
I
J

7
STEP 9
Do not push monitors too far back.
STEP 10
If monitor heights are not aligned, turn the screw behind each VESA plate using the 5mm allen wrench
(I). Clockwise will raise the monitor and counter-clockwise will lower the monitor.
I
360°
360°

LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303