Vivo STAND-V100G User manual

Pneumatic Arm Single Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v100g
SKU: STAND-V100G
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
TOOLS NEEDED
4.4-26.4lbs
(2-12kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
A (x1)
Arm
B(x1)
VESA Plate
C(x1)
Pole
J (x1)
Support Plate
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Base
E(x1)
Clamp
Brace
F (x1)
Clamp
G(x1)
Cover
H (x1)
Carriage Bolt
I (x1)
Grommet Base
K (x1)
M8 Nut
M-A (x4)
M4x12
M-B (x4)
M5x12
M-C (x4)
D5 Washer
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly
or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
S (x1)
6mm Allen
Wrench
L (x1)
M8 Washer
M (x3)
M6x16
R (x1)
4mm Allen
Wrench
N (x3)
M6x12
O (x2)
M6x10
P (x4)
Pad
Q (x1)
Cable Clip
T (x1)
Wrench

3
ASSEMBLY STEPS
STEP 1
OPTION A: Clamp Installation
Attach the pole (C) to the base (D) using
M6x16mm bolts (M) and tighten with the
4mm Allen wrench (R). Attach clamp brace
(E) to the base using M6x12mm bolts (N),
and tighten with the 4mm Allen wrench (R).
Apply pads (P) to each corner of the base.
For 3/8” - 2-5/32” (10-55mm) desktop
thickness, attach the clamp (F) to the
upper position on the clamp brace using
M6x10mm bolts (O) and tighten with the
4mm Allen wrench (R).
For 2” - 3-11/32” (50-85mm) desktop
thickness, attach the clamp (F) to the
lower position on the clamp brace using
M6x10mm bolts (O) and tighten with the
4mm Allen wrench (R).
Place the mount with clamp on the desk
edge and tighten the hand bolt. Place the
cover (G) on the back of the clamp.
OPTION B: Grommet Installation
Drop the carriage bolt (H) down through
the center hole of the grommet base (I),
making sure the counter-sink holes are
on the underside of the base. Attach the
grommet base with carriage bolt to the
base (D) using M6x12mm bolts (N), and
tighten with the 4mm Allen wrench (R).
Apply pads (P) to each corner of the base.
If a grommet hole is not present in the
desktop, drill a hole through the desktop
using a 3/8” (10mm) bit. Place the base
over the hole, then secure by attaching
the support plate (J) to the carriage bolt
protruding from underneath the desk using
the M8 nut (K) with M8 washer (L). Tighten
the M10 nut using the wrench (T).

4
STEP 2
Slide the cable clip (Q) and arm (A) down onto
the pole. Tighten the arm to the pole using the
6mm Allen wrench (S).
STEP 3
Attach the VESA plate (B) to the monitor using bolts (M-A or
M-B) with washers (M-C), making sure the arrow is facing
towards the top of the monitor, and tighten with a Phillips
screwdriver.

5
STEP 5
If needed, adjust the gas spring in the arm (A) to support the monitor using
the 6mm Allen wrench (S). While holding the arm in the straight forward
position, turn the screw in back clockwise to decrease support, and
counter-clockwise to increase.
CAUTION - To avoid damage to the monitor
and mount, always keep the arm in a horizontal
position while making adjustments.
STEP 4
Pull back the release lever on the support
bracket, then place the monitor with VESA
plate (B) into the support.

6
STEP 6
STEP 7
Adjust tilt support by turning the bolt on the side of the tilt joint using the 6mm Allen wrench (S).
Use the cable clips on the arm and pole to organize cables.

7

LAST UPDATED: 08/24/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303