Vivo STAND-V001R User manual

Pneumatic Arm Monitor & Touch Screen Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v001r
SKU: STAND-V001R
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Base
B(x1)
Monitor Arm
C(x1)
Lower Arm
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Cover
E(x1)
M4x8
F (x4)
M6x20
G(x1)
4mm Allen
Wrench
H (x1)
6mm Allen
Wrench
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M-A (x4)
M4x12
M-B (x4)
M5x12
M-C (x4)
D5 Washer

3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
4.4-22lbs
(2-10kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
Assemble the monitor arm (B) to the lower arm (C) using M6x20 bolts (F), and
tighten with the 4mm Allen wrench (G). Attach the cover (D) to the lower arm
using the M4x8 bolt (E).

4
STEP 2
Attach the assembled monitor arm to the base (A) using M6x20 bolts (F), and tighten with the 4mm
Allen wrench (G).
STEP 3
Insert 12mm bolts (M-A, M-B) with washers (M-C) into the top two mounting holes of
the monitor, leaving 3mm of thread exposed.

5
STEP 4
Hang the monitor over the slots in the VESA mounting plate, insert two
more bolts (M-A, M-B) with washers (M-C) into the lower two holes,
and tighten with a Phillips screwdriver.

6
STEP 5
Adjust tilt support by removing the cap from the side and tightening the bolt underneath with the
6mm Allen wrench (H), then replace the cap. Route cables through the opening in the lower arm.
STEP 6
To adjust gas spring support, hold the gas spring arm down to the straight-forward position and turn
the adjustment screw using the 6mm Allen wrench (H). Clockwise will reduce support, and
counter-clockwise will increase support.

7
Adjust as Desired

LAST UPDATED: 03/06/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303