Vivo STAND-TV65C User manual

Solid Wood TV Floor Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-tv65c
SKU: STAND-TV65C
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
A (x1)
Center Leg
B(x2)
Side Leg
C(x1)
Pole
D(x1)
Center Brace
P-A (x1)
Security Cable
P-B (x2)
Security Clip
P-C (x1)
Security Bracket
P-D x2)
Security Cable
Clamp
P-E (x1)
ST4.8x38mm
Screw
P-F (x1)
Anchor
M-A (x4)
M5x14mm Screw
M-B (x4)
M6x14mm Screw
M-C (x4)
M6x30mm Screw
M-D (x4)
M8x30mm Screw
M-E (x4)
M8x50mm Screw
M-F (x4)
Square Washer
M-G (x8)
Small Spacer
M-H (x8)
Big Spacer
P-G (x2)
M5 Washer
E (x1)
Upper VESA Bracket
F(x1)
Lower VESA Bracket
G(x1)
Cover
H(x1)
Collar
S-A (x3)
M6x70mm
Screw
S-B (x1)
M6x90mm
Screw
S-C (x1)
M45.5 Spacer
S-D x1)
M6x30mm
Screw
T-A x1)
4mm Allen
Wrench

3
TOOLS NEEDED
Phillips
Screwdriver Drill
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
88 lbs
(40 kg)
Level Pencil

4
ASSEMBLY STEPS
STEP 1
Assemble Side Legs (B) to Center Brace (D) using M6x70mm Screws (S-A) and 4mm Allen Wrench (T-A).
B
D
S-A
T-A

5
STEP 2
Loosen the screw on the back of Pole (C) using 4mm Allen Wrench (T-A) and connect Pole (C) to Center
Leg (A). Assemble Center Leg (A) to Center Brace (D) using M6x70mm Screw (S-A) and 4mm Allen
Wrench (T-A). Attach Cover (G) to the assembly.
NOTE: To remove Cover (G), press on the right side.
C
T-A
A
D
S-A
T-A
G

6
STEP 3
Ensure that the flathead screw in the back of Pole (C) is positioned vertically as shown below. Thread
M6x90mm Screw (S-B) into the bottom of Center Leg (A) using 4mm Allen Wrench (T-A). Retighten the
screw in the back of Pole (C) using 4mm Allen Wrench (T-A).
C
S-B
A
T-A
T-A

7
STEP 4
Slide Collar (H) and M45.5 Spacer (S-C) over Pole (C) and secure it in the desired location using
M6x30mm Screw (S-D) and 4mm Allen Wrench (T-A).
STEP 5
Remove the Security Screw (F1) from Lower VESA Bracket (F) and open the clamp.
F
F1
H
S-C
C
S-D
T-A

8
STEP 6
OPTION A: Flat Back Monitor
Position VESA brackets horizontally on the back of the TV, making sure Upper VESA Bracket (E) is on
top and Lower VESA Bracket (F) is below. Secure using screws (M-A or M-B) with Square Washers
(M-F), M5 Washers (P-G),and Security Clips (P-B) installed to top holes.
OPTION B: Curved Back Monitor
Position VESA brackets horizontally on the back of the TV, making sure Upper VESA Bracket (E) is on
top and Lower VESA Bracket (F) is below. Secure using screws (M-C, M-D or M-E) with Square Washers
(M-F) and Spacers (M-G, M-H) with Security Clips (P-B) installed to top holes.
F
F
E
F
E
F

9
STEP 7
Slide the TV with VESA Brackets (E, F) onto Pole (C), letting Upper VESA Bracket (E) rest on Collar (H).
Close the clamp on Lower VESA Bracket over Pole (C) and secure with previously removed Security
Screw (F1). Remove the magnetic cable channel cover on the back of Center Leg (A) and route cables.
E
F
C
F1
A
Magnetic Cover
>20mm

10
STEP 8 (Option A)
Wood Stud Wall
Using Security Bracket (P-C) as a guide, mark the drilling location on wall at the same height as
the upper VESA bracket. Use of a stud finder is recommended. Drill the hole at least 1.6” (40mm)
deep using a 1/8” (3.5mm) drill bit. Mount clamp to wall using ST4.8x38mm Screws (P-E). Thread
Security Cable (P-A) through Security Clips (P-B) on TV and center holes in Security Brackets (P-C)
as shown, then tighten Security Cable Clamps (P-D) with a Phillips screwdriver.
E