Vivo MOUNT-KB05ES-W User manual

Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-kb05es
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
White Clamp-on Small Keyboard Tray
SKU: MOUNT-KB05ES-W

2
ASSEMBLY STEPS
STEP 1
STEP 2
C
E
F
C
I
Assemble the Keyboard Tray (E) using Connecting Plates (F) and M5x12 Flat Head Screws (C), and
tighten with a Phillips screwdriver.
Attach the Keyboard Stop (I) to the back of the Keyboard Tray (E) using M5x12 Flat Head Screws (C).
Tighten with a Phillips screwdriver.
PACKAGE CONTENTS
TOOLS NEEDED
11lbs
(5kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualied technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specied in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
A(x6)
M4x7
B(x8)
M5x12
D(x2)
Pad
F (x2)
Connecting
Plate
C(x12)
M5x12 Flat Head
E(x1)
Keyboard
Tray
G(x2)
Sliding Bracket
H(x2)
Clamp
I(x1)
Keyboard Stop
NOTE: 2 Extra screws have been included of each

3
STEP 3
STEP 4
STEP 5
B
G
H
Right
Left
A
Desktop
D
Assemble Slider Brackets (G) to the Keyboard Tray (E) using M5x12 Screws (B), and tighten with a
Phillips screwdriver. The slider brackets should protrude from the back of the keyboard tray.
NOTE: If the keyboard tray is not sliding in completely , remove the keyboard backstop on the
tray. This will allow for an extra 0.75” (19mm) of clearance. If more clearance is needed, change the
orientation of the desk having the sync rod facing towards you. This will avoid the crossbar and cable
tray entirely.
Assemble Clamps (H) to the Slider Brackets (G) using M4x7 Screws (A). Tighten with a Phillips
screwdriver.
NOTE: Clamp can be oset using the extra holes in Slider Brackets (B) to allow the tray to be pulled
out an extra 1.2” (30mm) when in use. If mounted this way the tray will sit further out from desk edge.
Place Pads (D) on the underside of each clamp. Place assembled keyboard mount on the edge of the
desk and tighten clamps.
NOTE: To ensure keyboard tray is level, do not over-tighten clamps.
Slide keyboard tray forward/back to the desired position.

LAST UPDATED: 09/19/2022
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs):
309-278-5303