Vivo STAND-E-149 User manual

Electric Single Ultrawide
Monitor Desk Mount
Instruction Manual
SKU: STAND-E-149
Assembly Video & Product Info
www.vivo-us.com/products/stand-e-149

Contact Us First!
PERSONABLE CUSTOMER SUPPORT
Our friendly product support team is here to help!
DO NOT RETURN ITEM
We’re Here for You!
Missing a Part?
Our customer-minded support team is here for YOU,
Monday-Friday 7am-7pm CST.
We oer immediate assistance with rapid response times
from customer service agents and product techncians to
help you every step of the way!
Monday-Friday
Chat Us:
www.vivo-us.com
Give us a Call:
309-278-5303
Email Us:
[email protected]om
If any parts are received damaged / defective OR you are
missing a part, please reach out to us within 30 days of
product delivery to have it replaced at no cost.
We are happy to replace parts to ensure you have a fully
functioning product
7AM - 7PM

Product Warranty
Returns | Product Didn’t Work Out?
For the most up to date details on your product’s warranty, please visit
the product’s listing on our website or reach out to customer support.
vivo-us.com/products/stand-e-149
We oer a hassle-free 30 day return on all products. Contact customer
support at 309-278-5303 or [email protected]om. Please note: For items
ordered in error or no longer needed, the return shipping charges will
be at the buyer’s expense.
If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact our product
support team at 309-278-5303 or [email protected] for further assistance. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly
specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting,
incorrect assembly or inappropriate use.
LBS
CAUTION!
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
DO NOT EXCEED WEIGHT CAPACITY
FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY.
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND
ELECTRIC SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR SELLER TO
REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE MADE
CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
ELECTRICAL SAFETY INSTRUCTIONS

4
Package Contents
Included Hardware & Tools
F (x1)
VESA Plate
A (x1)
Electric Stand
B(x1)
Lower Clamp
Bracket
C(x1)
Upper Clamp
Bracket
D(x1)
Clamp Cable Clip
E(x1)
Arm Bracket
G (x1)
Cable Sleeve
H (x1)
AC Adapter
I (x1)
Power Cable
J (x1)
Control Panel
K (x1)
Power Cable
S-A (x4)
M6x12mm
Screw
S-B(x1)
Screw Cap
S-C (x1)
M3x8mm
Screw
M-A (x4)
M4x12mm
Screw
M-C (x4)
M5 Washer
T-A (x1)
4mm Allen
Wrench
M-B (x4)
M5x12mm
Screw
T-B (x1)
6mm Allen
Wrench
L(x1)
Large Pad
M(x2)
Small Pad N(x2)
Cable Clip
S-D (x2)
ST3.5x18mm
Screw

5
Phillips
Screwdriver
Pencil
Drill
Scissors
Tools Needed: Weight Capacity:
22lbs
(10kg)

6
ASSEMBLY STEPS
STEP 1
SECURE CLAMP BRACKET
Attach Upper Clamp Bracket (C) to the bottom of the Electric Stand (A) using M6x12mm
Screws (S-A) and 4mm Allen Wrench (T-A). Remove protective film from Large Pad (L) then
attach it to the bottom of the stand.
A(x1)
C(x1)
L(x1)
S-A (x4)
T-A
T-A
L
S-A
C
A

7
STEP 2 A. DESKTOPS 10-55mm (0.40”-2.15”)
FOR DESKTOPS 10-55mm (0.40”-2.15”)
Align the key slots on Lower Clamp Bracket (B) with the screws on Upper Clamp Bracket (C).
Pull Lower Clamp Bracket (B) down and lock the screws on Upper Clamp Bracket (C) in place
with the 4mm Allen Wrench (T-A).
PROCEED
TO STEP 3
B(x1)
6mm
10mm-55mm
T-A
B
C
T-A

8
FOR DESKTOPS 50-85mm (2”-3.35”)
Remove the screws on Upper Clamp Bracket (C) and reassemble them into the lower set of
holes using 4mm Allen Wrench (T-A).
Align the key slots on Lower Clamp Bracket (B) with the screws on Upper Clamp Bracket (C).
Pull Lower Clamp Bracket (B) down and lock the screws on Upper Clamp Bracket (C) in place
with the 4mm Allen Wrench (T-A).
T-A
T-A
STEP 2 B. DESKTOPS 50-85mm (2”-3.35”)
6mm
50-85mm
B(x1)
CT-A
C
B
T-A

9
T-A
D(x1)
STEP 3
STEP 4
SECURE CLAMP TO DESKTOP
Clamp the stand assembly onto desk and press the Clamp Cable Clip (D) onto Upper Clamp
Bracket (C).
ATTACH ARM BRACKET
Partially loosen the screw the on side of Arm Bracket (E) using 6mm Allen Wrench (T-B).
Slide Arm Bracket onto the post of Electric Stand (A) and secureusing 6mm Allen Wrench.
E (x1)
C
D
A
T-B
E

10
STEP 5
CONNECT VESA PLATE TO MONITOR
Attach VESA Bracket (E) to the monitor using either M4x12mm (M-A) or M5x12mm Screw
(M-B) and Washers (M-C) along with a Phillips Screwdriver.
M-A (x4)
M-B (x4)
M-C (x4)
F (x1)
or
F
M-C
M-A
M-B