Vivo STAND-TV70A User manual

Easel Studio TV Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-tv70a
SKU: STAND-TV70A
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Base
B(x2)
Pole
C(x4)
Leg
I (x6)
Cable Clip
J (x6)
3/8” Srew
K(x1)
2mm Allen
Wrench
H(x2)
Security Cable
Clamp
D (x1)
Upper VESA
Bracket
E (x1)
Lower VESA
Braket
F (x1)
Security
Cable
G (x2)
Security
Clip
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
M-F (x4)
Metal Spacer
M-G (x8)
Small Spacer
M-E (x4)
M8x50
M-A (x4)
M5x14
M-B (x4)
M6x14
M-D (x4)
M8x30
M-H (x8)
Big Spacer
M-C (x4)
M6x30
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
N (x4)
Concrete Anchor
M(x4)
ST4.8x38 Screw
L (x1)
4mm Allen
Wrench
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

3
ASSEMBLY STEPS
STEP 1
Screw the legs (C) into the base (A).
TOOLS NEEDED DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
STEP 2
Screw the poles (B) onto the top of the base.
88lbs
(40kg)
A
C
B
Drill
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO
MOUNT. We include mounting hardware for brick and concrete walls. If unsure, please contact us at
vivo-us.com, email at [e-mail], or call us at 309-278-5303.

4
STEP 3
Loosen the support rings on the poles using the 4mm Allen wrench (L). Adjust
rings to hold TV at desired height, using a tape measure to ensure the rings are
adjusted evenly, and tighten with the 4mm Allen wrench.
NOTE: Rings should be at least 2” below the tops of the poles.
STEP 4
Remove screws from lower VESA bracket (E) and open clamps.
2
Note:
Please secure the locking collar
before attaching the TV screen.
L
1
3
E1
E2

5
STEP 5
OPTION A: Flat Back Monitor
Position VESA brackets horizontally
on the back of the TV, making sure
upper VESA bracket (D) is on top and
lower VESA bracket (E) is below. Secure
using screws (M-A or M-B) with square
washers (M-F), with security clips (G)
installed to top holes.
OPTION B: Curved Back Monitor
Position VESA brackets horizontally
on the back of the TV, making sure
upper VESA bracket (D) is on top
and lower VESA bracket (E) is below.
Secure using screws (M-C, M-D or
M-E) with square washers (M-F) and
spacers (M-G, M-H) with security clips
(G) installed to top holes.
E1
D
M- F
M- A
M- F
M- B
M- F
G
M- A
M- F
G
M- B
TVTV
TVTV
E1
D
M- G
M- H
M- F
G
M- E
M- F
G
M- C
M- D M- E
M- F
M- C
M- D
M- F

6
STEP 6
Slide the TV with VESA brackets (D, E) onto poles. Close the clamps on lower VESA
bracket over the poles and secure with previously removed screws.
Peel backing from cable clips (I) and install clips on rear legs. Use clips to organize
cables.
Optional: Secure cable clips using 3/8” screws (J). Screws are able to thread
directly into wood without drilling pilot holes.
1
2
3
E2
I
J
1
2
3

7
STEP 7
ø 3.5mm
40mm
40mm
ø 7mm
(ø 9/23")
(1.6")
1
3
2
1100-1350mm
400-650mm
H
K
F
F
G
1 2
X
X
M
2
1
M
N
1100-1350mm
400-650mm
H
K
F
F
G
12
OPTION A: Wood Stud Wall
Using Security Cable Clamps (H) as guides,
mark drilling locations on wall at the same
height as the upper VESA bracket. Use of
a stud finder is recommended. Drill holes
at least 1.6” (40mm) deep using a 1/8”
(3mm) drill bit. Mount clamps to wall using
ST4.8x38 screws (M). Thread security cable
(F) through security clips on TV and center
holes in cable clamps as shown, then tighten
clamps using the 2mm Allen wrench (K).
OPTION B: Concrete/Brick Wall
Using Security Cable Clamps (H) as guides,
mark drilling locations on wall at the same
height as the upper VESA bracket, spaced
400mm - 650mm (16” - 26”) apart. Drill holes
at least 1.6” (40mm) deep using a 9/32”
(7mm) drill bit. Insert concrete anchors (N)
into holes and mount clamps to wall using
ST4.8x38 screws (M). Thread security cable
(F) through security clips on TV and center
holes in cable clamps as shown, then tighten
clamps using the 2mm Allen wrench (K).

LAST UPDATED: 04/27/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303