Vivo STAND-V003T User manual

Triple Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v003t
[email protected]om www.vivo-us.com 309-278-5303
SKU: STAND-V003T

2
PACKAGE CONTENTS
TOOLS NEEDED
WARNING!
Phillips
Screwdriver
A (x3)
VESA Plate
B(x1)
Monitor Mount
C(x1)
Arm
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Clamp
E (x1)
Pole
F (x1)
Pole
G (x1)
Pole Adapter
H (x2)
Cable Clip
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M-A (x12)
M4x12
M-B (x12)
M4x16
I (x1)
Grommet Base
J(x2)
VESA Cap
M-C (x12)
M5x12
M-F (x12)
Spacer
M-D (x12)
M5x16
M-E (x12)
D5 Washer
K (x2)
Small Screw
L (x5)
Rubber Pad
M (x3)
Large Screw
N (x1)
Grommet Plate
O(x1)
Knob
P (x1)
3mm Allen
Wrench
Q (x1)
4mm Allen
Wrench
R (x1)
6mm Allen
Wrench
17.6 lbs
(8 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM

3
ASSEMBLY STEPS
STEP 1
OPTION A: Clamp Installation
Apply rubber pads (L) to clamp (D) as shown in diagram. Attach clamp (D) to pole (E) with large screws
(M) using 4mm allen wrench (Q). Secure clamp (D) to desk.
OPTION B: Grommet Base Installation
Remove crank from clamp (D). Apply rubber pads (L) to grommet base (I) as shown in diagram. Place
on desk. Put grommet plate (N) on crank. Insert crank through desk and grommet base (I) from
below. Attach and tighten pole (E).
D
E
Q
M
L
D
L
I
N
10-75mm
E

4
STEP 2
Slide one cable management clip (H) onto pole (E). Slide arm (C) onto pole (E) and tighten in place
using 6mm allen wrench (R). Screw pole adapter (G) onto pole (E). Screw pole (F) into pole adapter.
Tighten using 3mm Allen wrench (P) as shown in diagram.
HC
E
R
E
G
F
P
Slide one cable management clip (H) onto pole (F). Slide monitor mount (B) onto pole (F) and tighten
in place using 6mm allen wrench (R).
STEP 3
B
H
R

5
STEP 4
INNER HOLES
Attach VESA plates (A) to monitors using screws (M-A or M-C) and washers (M-E).
OUTER HOLES
Attach VESA plates (A) to monitors using screws (M-B or M-D), washers (M-E), and spacers (M-F).
STEP 5
Slide VESA plates (A) with monitors attached onto monitor mounts as shown in diagram.
M- A
M- C
M- E
A
M- B
M- D
M- E
A
M- F

6
STEP 6
Use VESA caps (J) and small screws (K) to secure bottom two monitors as shown in diagram. Tighten
with 6mm allen wrench (R) as shown in diagram. Use knob (O) to secure top monitor as shown in
diagram. Tighten with 6mm allen wrench (R) as shown in diagram.
STEP 7
Use cable management clips (H) to manage cables. Use cable management clips (H) to store allen
wrenches.
R
K
J
O
P
Q
R

7
Adjust as Desired
±180°
+45°
-45°
R
+45°
-45°
±180°
+45°
-45°
±180°

LAST UPDATED: 10/28/2019
Open Monday-Friday from 7:00am-7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times.
If any parts are received damaged or defective, please contact us.
We are happy to replace parts to ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]
www.vivo-us.com
309-278-5303
AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
AVG. RESOLUTION TIME (within oice hrs): < 15 M