Vivo STAND-LIVE1M User manual

Mobile All-In-One Livestream Multi-Mount
Floor Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-live1m
SKU: STAND-LIVE1M
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
M-B (x4)
M5x12mm
Screw
PACKAGE CONTENTS
WARNING!
A (x1)
Adjustable
Pole
B(x1)
Ring Light
C(x1)
Mic Boom
J (x4)
Upper Arm
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly
or inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Laptop Tray
E(x4)
Legs
F (x1)
VESA Plate
G(x1)
Base
H (x2)
Cable Clip
I (x2)
Lower Arm
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
K (x1)
Dual Connector
L (x1)
Phone/Tablet
Holder
M (x1)
Mic Boom
Clamp
N(x1)
Mic Mount
O (x2)
Caster
P (x2)
Locking Caster
Q (x4)
Locking Pole
Ring
R(x1)
Pole Cover
TOOLS NEEDED
6.6lbs
(3kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
2.2lbs
(1kg)
MICROPHONE CAMERA & PHONE
11lbs
(5kg)
MONITOR
11lbs
(5kg)
LAPTOP
S(x2)
Threaded
Connector
T (x2)
Ball Head
S-A (x3)
M6x20mm
Screw
S-B (x8)
M6x25mm
Screw
S-C (x4)
M4x8mm
Screw
S-D (x4)
M5 Washer
T-A (x1)
4mm Allen
Wrench
T-B (x1)
5mm Allen
Wrench
T-C (x1)
Wrench
M-A (x4)
M4x12mm
Screw
M-C (x4)
M5 Washer
Phillips
Screwdriver

3
ASSEMBLY STEPS
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
Connect Legs (E) to Base (G) using M6x25mm Screws (S-B) and 5mm Allen Wrench (T-B). Attach
Casters (O) and Locking Casters (P) to Legs (E).
STEP 1
T-A
S-A
P
G
E
O
P
O
T-B
S-B
Secure assembled base to Adjustable Pole (A) using M6x20mm Screws (S-A) and 4mm Allen
Wrench (T-A).
Turn assembly over and adjust Caster (P) height using Wrench (T-C). Use side tab on Locking
Casters (P) to lock wheels in place during assembly of stand.
T-C P
A

4
STEP 2
Slide Cable Clip x2 (H), Locking Pole Ring x4 (Q), Lower
Arm x2 (I), and Dual Connector (K) onto Adjustable Pole
(A) following the order shown below.
Tighten set screw of Locking Pole Ring (Q) using 4mm
Allen Wrench (T-A).
Stand can now be customized as desired
with mounting arms and accessories.
The following steps give an example of how
stand arms and accessories can be mounted.
K
I
I
Q
H
A
CAUTION : Properly balance the le and right weight
distribution of the arms to prevent tipping.
Height Adjustment
Twise the Height Adjuster (A1) on Pole (A)
to raise or lower the Pole. Lock into place
by tightening the set screw on Locking Pole
Ring (Q) directly above Height Adjuster
(A1) using 4mm Allen Wrench (T-A).
A
T-A
Q
A1

5
STEP 3
Connect Upper Arm (J) to right side Lower Arm (I), then install VESA
Plate (F) to Upper Arm (J). Secure by tightening set screws using
4mm Allen Wrench (T-A).
Attach Upper Arm (J) to le side Lower Arm (I), and secure by tightening set screws using 4mm Allen
Wrench (T-A). Insert Threaded Connector (S) into Upper Arm (J).
I
J
S
F
J
I
T-A
STEP 4
T-A

6
Screw Ball Head (T) onto Threaded Connector (S), then screw Ring Light (B) onto Connector.
STEP 6
T
S
J
STEP 5
Connect Upper Arm (J) to Dual Connector (K), then connect a second Upper Arm (J), as shown
below. Install Threaded Connector (S) to Upper Arm (J).Secure by tightening set screws using 4mm
Allen Wrench (T-A).
J
J
S
T-A
K
B

7
STEP 7
If needed, install the
5/8” Adapter, as shown.
C
T-A
C
K
M
C
Connect Mic Boom (C) to remaining mounting hole in Dual Connector (K). Twist Mic Mount (N) onto
Mic Boom (C). Optional: Mic Boom (C) can be desk mounted using Mic Boom Clamp (M).
N

8
STEP 8
For VESA Plate (F), choose between Monitor or Laptop Holder.
Monitor: Attach Screws (M-A or M-B) and M5 Washers (M-C) in the top VESA holes on monitor,
using a Phillips screwdriver. Slide onto VESA Plate (F) and attach remaining two Screws (M-A or
M-B) and M5 Washers (M-C).
Laptop: Attach M4x8mm Screws (S-C) and M5 Washer (S-D) into Laptop Tray, partially protruding,
using Phillips screwdriver. Slide onto VESA Plate (F) and attach remaining M4x8mm Screws (S-C)
and M5 Washers (S-D).
S-C
S-D
D
F
S-CS-D

9
STEP 9
T-A
L
T
T
S
S
Twist Ball Head (T) onto Threaded Connector (S), then connect Phone/Tablet Holder (L).
NOTE: Ball Head (T) can also be used to mount cameras, and other multi-media devices.
VESA Plate (F) can be adjusted using 4mm Allen Wrench (T-A) to allow monitor to tilt, turn, and
swivel.
Optional

10
Remove bottom covers from Lower Arms (I) and Upper Arms (J) by sliding o. Organize cables
and slide covers back on.
STEP 10
J
J
J
J
I
I