Vivo STAND-V200T User manual

Dual Ultrawide Vertical Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v200t
SKU: STAND-V200T
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
TOOLS NEEDED
44lbs
(20kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
A (x1)
Base
F (x2)
Cable Clip
G (x1)
Clamp Plate
H (x1)
Grommet Plate
I (x1)
So Pad
J (x1)
Cover
K (x1)
Clamp Brace
B (x2)
Arm
C (x1)
Lower Pole
D (x1)
Upper Pole
E (x2 )
VESA Plate
S-B (x4)
M6x12mm Screw
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualied technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specied in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly
or inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
M-B (x8)
M5x14mm Screw
M-C (x8)
M5 Washer
M-A (x8)
M4x14mm Screw
T-A (x1)
4mm Allen Wrench
T-B (x1)
6mm Allen Wrench
T-C (x1)
Wrench
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
S-A (x4)
Wing Nut
L (x1)
Lower Clamp
M (x2)
Pole Cable Clip
Per Arm

3
ASSEMBLY STEPS
STEP 1 - Option A - Clamp
Connect Clamp Brace (K) to Base (A) using M6x12mm Screws (S-B) and 4mm Allen Wrench (T-A).
Remove protective lm from So Pad (I) and apply to the underside of Clamp Brace (K). Loosen the
screws on the back of Lower Clamp (L) using 4mm Allen Wrench (T-A), leaving 6mm of thread exposed.
Desk Thickness 0.4” to 2.25” (10mm-58mm)
Hang Lower Clamp (L) into the top 4 slots on
Clamp Brace (K). Tighten rear screws with
4mm Allen Wrench (T-A). Place Clamp Plate (G)
on top of the clamp bolts on Lower Clamp (L).
Desk Thickness 2” to 3.35” (50mm-85mm)
Hang Lower Clamp (L) into the lower 4 slots
on Clamp Brace (K). Tighten rear screws with
4mm Allen Wrench (T-A). Place Clamp Plate (G)
on top of the clamp bolts on Lower Clamp (L).
Install to desk and tighten clamp bolt using 6mm Allen Wrench (T-B). Snap Cover (J) onto the
back of assembled base.
T-A L
I
S-B
K
A
K
T-A
T-B J
K
L
GG
L
T-A

4
STEP 2
Screw Lower Pole (C) into Base (A), and tighten set screws using 4mm Allen Wrench (T-A). Slide Pole
Cable Clip (M) onto Lower Pole (C).
STEP 1 - Option B - Grommet
Attach Grommet Plate (H) to Base (A) using M6x12mm Screws (S-B) and 4mm Allen Wrench (T-A).
Remove protective lm from So Pad (I) and apply to the underside of Grommet Plate (H).
Position Base (A) over grommet hole in desk. If there is no existing grommet hole, drill a 0.375”
(10mm) hole through the desktop in the desired mounting position.
Remove a single clamp bolt from Lower Clamp (L) using 6mm Allen Wrench (T-B). Insert clamp bolt
with Clamp Plate (G) through the underside of the desk and secure to Base (A) using 6mm Allen
Wrench (T-B).
HA
T-A
H
I
T-B T-B
L
G
A
C
M
T-A
A

5
STEP 3
Slide one Arm (B) onto Lower Pole (C) and secure using 6mm Allen Wrench (T-B). Thread Upper
Pole (D) onto Lower Pole (C). Attach Pole Cable Clip (M) to Upper Pole (D).
STEP 4
Slide remaining Arm (B) onto Upper Pole (D) and tighten to the pole using 6mm Allen Wrench (T-B).
Attach Cable Clips (F) to Arms (B).
B
C
M
D
T-B
B
B
FD
T-B

6
STEP 5
STEP 6
Partially install one Wing Nut (S-A) to the top screw on VESA Plate (E) on monitor and hang over the
slot in the top of Arm (B). Install the second Wing Nut (S-A) to the lower screw on VESA Plate (E).
S-A
B
E
S-A
Install VESA Plate (E) to your monitor using appropriate Screws (M-A, M-B), M5 Washer (M-C) and a
Phillips screwdriver.
M-A
M-B
M-C
E

7
Adjust as Desired
Cable Management
Adjust the tilt support screws using 4mm Allen Wrench (T-A) and swivel joints using Wrench (T-C).
Organize cables using Cable Clips (F), Pole Cable Clips (M), and Cover (J).
T-B
T-C
M
J
F

LAST UPDATED: 04/12/2023
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303