Vivo STAND-V001O User manual

Pneumatic Arm Single Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v001o
SKU: STAND-V001O
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
4.4-19.8lbs
(2-9kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PACKAGE CONTENTS
A (x1)
Lower Arm
B(x1)
Upper Arm
C(x1)
Base
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
S-C (x1)
M8x30mm
Screw
G (x1)
VESA Plate
S-A (x2)
M6x8mm Screw
E (x1)
Upper Clamp
D (x1)
Lower Clamp
F (x1)
Grommet Plate
M-A (x4)
M4x12mm
Screw
M-B (x4)
M5x12mm
Screw
S-B (x2)
M6x10mm Screw
T-B (x1)
4mm Allen Wrench
M-C (x4)
M5 Washer
T-A (x1)
5mm Allen Wrench
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

3
ASSEMBLY STEPS
STEP 1 - Clamp Installation
Remove Plastic Cover (C1) from Base (C). Adjust the hand bolt completely down on Lower Clamp (D).
.”-.” (-mm) DESKTOPS .”-.” (-mm) DESKTOPS
Install Upper Clamp (E) to Base (C) using
M6x8mm Screws (S-A) and 5mm Allen
Wrench (T-A).
Install Upper Clamp (E) to Base (C) using
M6x8mm Screws (S-A) and 5mm Allen
Wrench (T-A).
Reinstall Plastic Cover (C1) onto Base (C). Reinstall Plastic Cover (C1) onto Base (C).
Attach Lower Clamp (D) to the top two
holes on Upper Clamp (E) using M6x10mm
Screws (S-B) and 4mm Allen Wrench (T-B).
Secure clamp assembly to the desktop.
Attach Lower Clamp (D) to the bottom two
holes on Upper Clamp (E) using M6x10mm
Screws (S-B) and 4mm Allen Wrench (S-B).
Secure clamp assembly to the desktop.
C1 D
C
T-A T-A
CC
EE
C1 C1
C C
S-AS-A S-AS-A
T-B
T-B
D
D
EE
S-B
S-B

4
STEP 1 - Grommet
STEP 2
If desktop does not have a preexisting grommet hole, use a ⅜” (10mm) drill bit to create one by
drilling completely through the desktop.
Place Lower Arm (A) onto Base (C), then place Upper Arm (B) onto Lower Arm (A). Tighten set
screws using the flathead end on 4mm Allen Wrench (T-B).
Disassemble Lower Clamp (D) using the Phillips end on 5mm Allen Wrench (T-A) and separate
Hand Bolt (D1). Place Grommet Plate (F) on Hand Bold (D1) and secure Base (C) to the desktop.
Preexisting
Grommet
T-A
F
C
D
D1
B
A
C
T-B
D
T-B

5
STEP 3
STEP 4
Attach VESA Plate (G) to Upper Arm (B) using M8x30mm Screw (S-C) and 5mm Allen Wrench (T-A).
Install two Screws (M-A or M-B) and M5 Washers (M-C) using the Phillips end of 5mm
Allen Wrench (T-A) to the top VESA holes on the monitor leaving at least 3mm of
clearance between the screw and monitor. Slide the monitor onto VESA Plate (G) making
sure the screws sit within the slots.
Tighten the top two screws and install the remaining Screws (M-A or M-B) and 5mm Washers (M-E)
using the Phillips end of 5mm Allen Wrench (T-A).
G
G
M-A
M-B
M-C
T-A
BS-C
T-A
M-A
M-B
M-C
T-A

6
Cable Management
Adjust as Desired
Remove plastic covers from Arms (A,B)
using Phillips screwdriver end of 5mm
Allen Wrench (T-A). Run cables from
monitor through bottom of Arms (A,B),
then reattach plastic covers.
Use 5mm Allen Wrench (T-A) to adjust tilt.
B
A
T-A
T-A

7
Tension Adjustment
While holding the arm in the horizontal position, adjust the gas spring tension using the
5mm Allen Wrench (T-A).
T-A
WARNING:
Monitor must be installed on mount before making tension adjustments to the gas spring
arm.
CAUTION:
To avoid damage to the monitor or mount,
always ensure the arm is in a horizontal position
before making adjustments. An additional
person may be required to assist in some cases.
CAUTION:
Do not over tighten screws.

LAST UPDATED: 05/16/2023
REV3
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303