Vivo MOUNT-G100B User manual

Premium Aluminum Single Monitor Wall Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-g100b
SKU: MOUNT-G100B
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
TOOLS NEEDED
4.4-15.4lbs
(2-6.99kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
A (x1)
Arm
B(x2)
Screw Cover
C(x1)
5mm Allen
Wrench
W-A (x2)
Screw
W-B (x2)
Anchor
M-A (x4)
M4x12
M-B (x4)
M5x12
M-C (x4)
D5 Washer
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
Drill
W-C (x2)
Washers
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO
MOUNT. We include mounting for brick and concrete walls. If unsure, please contact us at vivo-us.
com, email at [email protected], or call us at 309-278-5303.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
Flat Blade
Screwdriver

3
ASSEMBLY STEPS
STEP 1
OPTION A: Wood Wall
Using the wall plate on the arm (A), mark
drilling locations. Use of a stud finder is highly
recommended. Drill 2.2” (55mm) deep holes using
a 3/16” (4.5mm) drill bit, and mount the arm to
the wall using screws (W-A) and washers (W-C).
OPTION B: Concrete/Brick Wall
Using the wall plate on the arm (A), mark drilling
locations. Drill 2.4” (60mm) deep holes using a
3/8” (10mm) drill bit, press anchors (W-B) into
holes, and mount the arm to the wall using screws
(W-A) and washers (W-C).NOTE: Anchors are
made for use with concrete or brick, and will not
work with drywall.
A
X
W- A
W- C
NP
O
XX
√
O
N
uu
√
A
W- A
W- C
W- B

4
STEP 2
Attach screw covers (B) to wall plate.
STEP 3
Insert bolts (M-A or M-B) with washers (M-C) into top two holes of TV/monitor, leaving 3mm of thread
exposed. Hang TV/monitor over slots in VESA mounting plate, insert bolts with washers into lower two
holes, and tighten.
B
3mm
M- A
M- B
M- C
1
M- A
M- B
M- C
2

5
STEP 4
Adjust gas spring tension using the Allen wrench (C). Turn counter-clockwise to increase li, and
clockwise to decrease. Adjust the tilt joint support using the Allen key. NOTE: use a large flat-blade
screwdriver to tighten the socket set screw if the joint makes a popping noise.
C
C

6
STEP 5
Use built in cable clips to manage cables.

7
Adjust as Desired
±180°
+45°
-45°
±90°
±180°
±90°

LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303