Vivo STAND-TV65B User manual

Black Easel Studio TV Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-tv65b
SKU: STAND-TV65B
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
88lbs
(40kg)
A (x2)
Leg
B(x1)
Center Leg
C(x1)
Lower VESA
Bracket
E (x1)
Pole
D(x1)
Upper VESA
Bracket
H (x1)
Steel Cable
G (x2)
Security Clip
F (x2)
Cable Clamp
S-A (x2)
M5x12mm Screw
T-A (x1)
2mm Allen Wrench
T-B (x1)
4mm Allen Wrench
S-B (x4)
ST4.8x38mm
Screw
S-C (x4)
Concrete Anchor
M-A (x4)
M5x14mm Screw
M-B (x4)
M6x14mm Screw
M-C (x4)
M6x30mm Screw
M-D (x4)
M8x30mm Screw
M-E (x4)
M8x50mm Screw
M-F (x4)
Square Washer
M-G (x8)
Small Spacer
M-H (x8)
Large Spacer
S-D (x2)
M5 Washer

3
E
ASSEMBLY STEPS
STEP 1
Remove the cable management cover from Center Leg (B). Assemble Center Leg (B) to Pole (E) using
M5x12mm Screws (S-A) and a Phillips screwdriver. Screw Legs (A) into base of Pole (E).
TOOLS NEEDED
Phillips
Screwdriver
STEP 2
Adjust collar height on Pole (E) using 4mm
Allen Wrench (T-B).
Drill Tape Measure Level Pencil
B
E
A
S-A
T-B
Recommended spacing:
50-150mm (2”-5.9”)

4
STEP 3
Remove the screw from the center clamp of Lower VESA Bracket (C) and open the clamp.
STEP 4
OPTION A: Flat Back Monitor
Position Lower VESA Bracket (C) and Upper VESA Bracket (D) horizontally on the back of
the TV, making sure Upper VESA Bracket (D) is on top and Lower VESA Bracket (C) is below.
Secure using Screws (M-A or M-B) with Square Washers (M-F) and M5 Washers (S-D), with
Security Clips (G) installed to top holes.
Ma ke s ure th e ca ble cl ips (P -B ) ar e at tach ed t o th e
upper br ac ket fo r th e fo llow ing se cu rity i nsta llation .
Too Shor t
Too long
M- F
M- A
M- F
M- B
M- F
M- A
M- F
M- B C2
C
S-D
GGD
C

5
STEP 4 (Continued)
OPTION B: Large or Curved Back Monitor
Position Lower VESA Bracket (C) and Upper VESA Bracket (D) horizontally on the back of the TV,
making sure Upper VESA Bracket (D) is on top and Lower VESA Bracket (C) is below. Secure using
Screws (M-C, M-D or M-E) with Square Washers (M-F) and Spacers (M-G, M-H) with Security Clips (G)
installed to top holes.
Too long Too Shor t
Ma ke s ure th e ca ble cl ips ( P-B ) ar e at tach ed t o th e
uppe r br ac ket fo th e fo llowi s ec urity i nsta llation.
M- E
M- C
M- D
M- G
M- H
M- G
M- H
M- FM- F M- FM- F
M- C
M- D
M- G
M- H
M- FM- F
M- E
M- G
M- H
M- FM- F
C2
STEP 5
Slide the TV with VESA brackets (C, D)
onto Pole (E). Close the clamp on Lower
VESA Bracket (C) over Pole (E) and
secure with previously removed screw.
STEP 6
Remove the cable management cover from Pole
(E) and route cables through the pole and Center
Leg (B). Reinstall cable management covers.
GG
D
C
E
C
D
E
B

6
STEP 7
OPTION A: Wood Stud Installation
Use a stud finder and a level to locate two adjacent studs. Using Cable Clamps (F) as guides, mark
drilling locations on the wall. Drill a 1.6” (40mm) deep hole using a 1/8” (3.5mm) drill bit. Mount
Cable Clamps (F) to wall using ST4.8x38mm Screws (S-B). Thread Steel Cable (H) through Security
Clips (G), then through the center holes in the Cable Clamps (F) as shown, then tighten using 2mm
Allen wrench (T-A).
P-B
P-A
P-D
P-A
P-C
mJ
mJ_
mJa
mJ^
F
1100-1350mm
400-650mm
= F
QM
NK
40mm
(1.6”)
S-B
F
ø 3.5mm
(ø 1/8”)
G
H
T-A
H
F

7
`
STEP 7 (Continued)
OPTION B: Concrete/ Brick Installation
Using Cable Clamps (F) as guides, mark drilling locations on wall. Drill holes at least 1.6” (40mm)
deep using a 9/32” (7mm) drill bit. Insert Concrete Anchors (S-C) in holes and mount Cable Clamps
(F) to the wall using ST4.8x38mm Screws (S-B). Thread Steel Cable (H) through Security Clips (G) and
through the center holes in the Cable Clamps (F) as shown, then tighten Cable Clamps (F) using 2mm
Allen Wrench (T-A).
S-C
S-B
F
mJ_
G
H
T-A
H
F
F
1100-1350mm
400-650mm
40mm
(1.6”)
ø 7mm
(ø 9/32”)

LAST UPDATED: 01/26/2022
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303