Vivo STAND-V102H User manual

Pneumatic Arm Dual Monitor Desk Mount with Pull Handle
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v102h
SKU: STAND-V102H
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
TOOLS NEEDED
WARNING!
Phillips
Screwdriver
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
A (x1)
Base
B(x1)
Adjustable Arm
C(x1)
Rear Cover
P (x4)
M6x12
L (x2)
Carriage Bolt
M (x2)
Support
Plate
N (x2)
D8 Washer
O (x2)
M8 Nut
M-A (x8)
M4x12
E(x1)
Grommet Base
Plate
G(x1)
Clamp
Bracket
H (x2)
Clamp Bolt
I(x1)
Monitor Arm
J (x1)
Handle
K (x2)
VESA Plate
M-B (x8)
M5x12
M-C (x8)
D5 Washer
D(x1)
Clamp Brace
F (x1)
Clamp Plate
R (x4)
M6x12
Flat Head
Q(x2)
M6x30
22lbs
(10kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM
S (x1)
Wrench
T (x1)
4mm Allen
Wrench
U (x1)
6mm Allen
Wrench

3
ASSEMBLY STEPS
STEP 1
OPTION A: Clamp Installation
Attach clamp brace (D) to base (A) using M6x12 flat head bolts (R), and tighten with 4mm Allen
wrench (T). Insert clamp bolts (H) into clamp bracket (G) as shown, then place clamp plate (F) on
top of assembled clamp. Install clamp (G) to upper holes of clamp brace (D) for a desk thickness
of 3/8” to 1-1/2” (10 - 40mm), or to lower holes for a desk thickness of 1-1/2” to 3-1/4” (40 - 84mm).
Place assembled base on edge of desk and tighten clamp bolts evenly with 6mm Allen wrench (U).
OPTION B: Grommet Installation
Place carriage bolts (L) into square holes in grommet base plate (E). Attach grommet base plate to
base (A) using M6x12 flat head bolts (R), and tighten with 4mm Allen wrench (T). Place assembled
base over cable grommet hole in desktop, and tighten using support plates (M), D8 washers (N)
and M8 nuts (O), and tighten with wrench (S). If a grommet hole isn’t present, drill two 3/8” (10mm)
holes 49mm apart through the desktop.

4
STEP 2
Insert the adjustable arm (B) into the
socket of the base, then secure using
the 4mm Allen wrench (T) or a flat-blade
screwdriver. Install rear cover (C) to clamp
brace if the clamp option was used.
STEP 3
STEP 4
Assemble monitor arm (I) to adjustable arm (B) using M6x12 bolts (P) with the 4mm Allen wrench (T).
Mount handle (J) to back of monitor arm using M6x30 bolts (Q) to one of the positions shown in the
diagram according to the size of your monitors. Tighten with 4mm Allen wrench (T).

5
STEP 5
Install the VESA plates (K) to monitors using M4x12 bolts (M-A) or M5x12 bolts (M-B) with
washers (M-C), making sure the rounded edges of the rear brackets are facing up.
STEP 6
Pull back the latch on each support bracket on monitor arm (I), then place the
monitors with VESA plates onto the support brackets.

6
STEP 7
While holding the arm in the horizontal position, adjust the gas spring tension
using the 6mm Allen wrench (U).
STEP 8
Remove cable covers from base and adjustable arm. Organize cables and
reinstall cable covers to base and adjustable arm.
CAUTION - To avoid damage to the monitor
and mount, always keep the arm in a horizontal
position while making adjustments.

7
STEP 9
Tighten or loosen the tilt joints using the 6mm Allen wrench (U). Slightly loosen the monitor arm for
leveling using the 4mm Allen wrench (T) if needed. Adjust the monitor position as desired.

LAST UPDATED: 07/23/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303